SAE AS 22520 35-2011 CRIMPING TOOLS TERMINAL HAND WIRE TERMINATION IN-SERVICE INSPECTION GAGES FOR AS22520 34 CRIMP TOOLS《线端手动压接工具端子 AS22520 34压接工具工作中检查量规》.pdf

1、 AEROSPACE STANDARD CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGES FOR AS22520/34 CRIMP TOOLS AS22520/35Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by a

2、ny means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae

3、.org ISSUED2011-09 REAFFIRMED2016-11 THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5220 AS22520/35 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS22520 SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateoftechnicaland engineering sciences. The us

4、e of this report isentirely voluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancel

5、led. SAE invites yourwrittencomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/35 RATIONALE AS22520/35 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR

6、PROCURING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF: SAE AS22520 CHART 1- SURFACE MARKING (SURFACE SEQUENCE OPTIONAL) UNDESIGNATED SURFACES HANDLE MARKING FIRST SURFACE TOOL PART NUMBER (SEE TABLE 1) SECOND SURFACE MFG.NAME AND TOOL PART NO. THIRD SURF

7、ACE DO NOT CRIMP GAGE AEROSPACE STANDARD AS22520/35 SHEET 2 OF 2 CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGES FOR AS22520/34 CRIMP TOOLS TABLE 1 GAGE DIMENSIONS AND MARKINGS PART NO. A .0001 DIA B .0001 DIA STAMPING SURFACES MARKING USE FOR INSPECTION OF TOOL C D E F

8、 M22520/34-01 M22520/35 .0300 .0350 USE SEL. 6 FOR M22520/34-01 - .0300 .0350 REQUIREMENTS: AS SPECIFIED IN AS22520. 1. DIMENSIONS: UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES AS SPECIFIED IN FIGURE 1 AND TABLE 1. CONFIGURATION IS OPTIONAL WITHIN DEFINED DIMENSIONS. TOLERANCES ARE DECIMALS

9、.010 INCHES. DIMENSIONS A AND B APPLY AFTER PROTECTIVE COATING (SEE REQUIREMENT 3). 2. MATERIAL: GAGE PINS: ALLOY TOOL STEEL PER ASTM A681, ASTM-A295, OR EQUIVALENT (CLASS OPTIONAL). HARDEN TO ROCKWELL C58-64. GAGE HANDLE: ALUMINUM ALLOY, ASTM B211 ALUMINUM AND ALUMINUM-ALLOY BAR, ROD, AND WIRE 3. F

10、INISH: GAGE PINS; CHROME PLATE WITH ADEQUATE COVERAGE FOR CORROSION AND WEAR RESISTANCE PER AMS-QQ-C-320 PLATING CHROMIUM, CLASS I, TYPE II WITH A THICKNESS OF .00003 INCHES MINIMUM. GAGE HANDLE: ANODIZED IN ACCORDANCE WITH MIL-A-8625. 4. MARKING: UNLESS OTHERWISE SPECIFIED, STAMPING SHALL BE INDENTED. LASER ETCHING IS ALSO ACCEPTABLE. 5. STORAGE CONTAINER: EACH GAGE SHALL BE FURNISHED WITH A SUITABLE CONTAINER. APPLICATION NOTES: 1. TOOL USED AS A GO/NO-GO VERIFICATION INSPECTION GAGE FOR AS22520/34 TOOLS SPECIFIED IN TABLE 1.