SAE AS 22759 187B-2017 WIRE ELECTRICAL POLYTETRAFLUOROETHYLENE POLYIMIDE INSULATED SMOOTH SURFACE NORMAL WEIGHT NICKEL-COATED COPPER CONDUCTOR 260 600 VOLTS ROHS.pdf

1、 AEROSPACE STANDARD WIRE, ELECTRICAL, POLYTETRAFLUOROETHYLENE/ POLYIMIDE INSULATED, SMOOTH SURFACE, NORMAL WEIGHT, NICKEL-COATED COPPER CONDUCTOR, 260 C, 600 VOLTS ROHS AS22759/187Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retriev

2、al system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Customer

3、Servicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2010-02REVISED2017-09THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8D REV.BFEDERAL SUPPLY CLASS 6145 AS22759/187 SHEET 1 OF 6 REV. B PROCUREMENT SPECIFICATION: NONE SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance

4、the state oftechnicaland engineering sciences.The use ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfive yearsatwhich time itmaybe revis

5、ed,reaffirmed,stabilized,orcancelled.SAEinvitesyourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS22759/187B RATIONALE SPECIFICATION UPDATED TO INCLUDE AS29606 CONDUCTOR REQUIREMENTS, ROHS RESTRICTIONS, AND A

6、S22759 MODIFICATIONS. THIS CHANGE ALSO INCREASES THE MAXIMUM WEIGHT REQUIREMENTS FOR WIRE SIZES 8 THROUGH 02 TO ACCOUNT FOR INCREASED CIRCULAR MIL AREA (CMA) ADOPTED IN AS29606. AS22759 IS A CONVERTED MILITARY SPECIFICATION ORIGINALLY NOTED AS MIL-W-22759 CREATED IN 1971. CONDUCTOR REQUIREMENTS WERE

7、 ORIGINALLY DEFINED BY ASTM B3, B298, AND B355 FOR TIN, SILVER, AND NICKEL PLATE RESPECTIVELY. THESE SPECIFICATIONS CONTROLLED THE CONDUCTOR BY ESTABLISHING STRAND SIZE, CONDUCTOR SIZE AND MAXIMUM DCR (DIRECT CURRENT RESISTANCE). BY THE LATE 1980S CONDUCTOR PRODUCERS WERE PRODUCING TIGHT TOLERANCE C

8、ONDUCTORS WHICH WERE MADE AT THE MINIMUM DIMENSIONAL AND MAXIMUM DCR LIMITS OF THE SPECIFICATION TO REDUCE THE WEIGHT (MASS) OF THE FINALLY INSULATED WIRE. BY THE EARLY 1990S THE TIGHT TOLERANCE CONDUCTORS WERE PREVALENT THROUGHOUT AEROSPACE. ABOUT THE SAME TIME, LARGE GAUGE SIZE CONDUCTORS (SIZE 8

9、THROUGH 4/0) STARTED EXHIBITING CRIMP FAILURES IN TERMINAL LUGS MOUNTED ON AIRCRAFT GENERATORS. SINCE THESE CIRCUITS ROUTED PRIMARY ELECTRICAL POWER FROM THE GENERATOR TO THE MAIN POWER DISTRIBUTION CENTERS, CRIMP DEGRADATION RESULTING IN DISRUPTION OF ELECTRICAL POWER CAUSED SIGNIFICANT CONCERN. SE

10、VERAL OEMS AS WELL AS NAVY AND AIR FORCE LABORATORIES INVESTIGATED THE FAILURES AND DETERMINED THAT THE FAILED CRIMPS WERE DUE TO A COMBINATION OF LOW CMA, HIGH VIBRATION AND THERMAL CYCLING. ADDITIONAL TESTING ESTABLISHED MINIMUM CMA LEVELS WHICH WOULD PREVENT THE CRIMP FAILURES. THESE NEW LIMITS W

11、ERE OFFERED TO ASTM BUT REJECTED. NAVAIR THEN PRODUCED AN ENGINEERING POSITION LETTER (EPL) TO MANDATE THE INCREASED CMAS ON STRANDING USED IN AS22759 CONSTRUCTIONS. NAVAIR THEN CREATED MIL-W-29606 WHICH WAS INTENDED TO REPLACE THE ASTM SPECIFICATIONS AS THE REQUIRED CONDUCTOR SPECIFICATION. BEFORE

12、THE MIL-W-29606 COULD BE ADDED TO MIL-W-22759, THE SPECIFICATION TRANSITION AND ADOPTION TOOK PLACE CONVERTING THE DOCUMENTS FROM MILITARY SPECIFICATIONS TO AS DOCUMENTS IN THE 1999 TO 2000 TIME FRAME. SINCE THE EPL NO LONGER HAD LEGAL STANDING AFTER THE CONVERSION, WIRE PRODUCERS DID NOT HAVE TO AB

13、IDE BY THE RESTRICTIONS WHICH ALLOWED THIS ISSUE TO CREEP BACK INTO THE PRODUCTS FROM TIME TO TIME. IN 2011, THE SAE AE-8D COMMITTEE OPENED A PROJECT TO UPDATE THE AS22759 AND ITS ASSOCIATED DETAILED SPECIFICATION SHEETS. WHEN LOOKING AT THIS ISSUE, THE COMMITTEE DECIDED TO ADOPT MIL-W-29606 (NOW AS

14、29606) AND REPLACE THE ASTM REQUIREMENTS WITH THE AS29606 REQUIREMENTS. SINCE THE DIAMETER RANGE OF THE CONDUCTOR STRANDS NEEDED TO SHIFT SLIGHTLY TO THE RIGHT TO MEET THE NEW MINIMUM CMA REQUIREMENTS, OVERALL PRODUCT WEIGHT MAXIMUMS SHIFTED ABOUT 3 TO 5%. THE COMMITTEE EVALUATED SEVERAL METHODS OF

15、INCORPORATING THIS CHANGE INCLUDING CANCELING AND SUPERSESSION, BUT THE END USERS DID NOT WANT TO CHANGE PART NUMBERS FOR PRODUCTS WHICH HAVE BEEN USED IN AEROSPACE AND INDUSTRY FOR OVER 40 YEARS AND IS CURRENTLY ON THOUSANDS OF DRAWINGS. SINCE THESE PRODUCTS ARE PRIMARILY USED FOR PRIMARY POWER DIS

16、TRIBUTION FROM THE GENERATORS TO THE MAIN DISTRIBUTION PANELS, THE WEIGHT INCREASE TO THE ELECTRICAL INTERCONNECT SYSTEM IS CONSIDERED INSIGNIFICANT. SINCE THIS CHANGE DOES AFFECT THE MAXIMUM WEIGHT LIMITS FOR SIZES 8 THROUGH 4/0, END USERS SHOULD VERIFY THAT THE NEW WEIGHT RANGES MEET THE DESIGN RE

17、QUIREMENTS OF LEGACY APPLICATIONS. CORRECTED STATE OF SINTER REQUIREMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS22759. AEROSPACE STANDARD AS22759/187 SHEET 2 OF 6 REV. B WIRE, ELECTRICAL, POLYTETRAFLUOROET

18、HYLENE/POLYIMIDE INSULATED, SMOOTH SURFACE, NORMAL WEIGHT, NICKEL-COATED COPPER CONDUCTOR, 260 C, 600 VOLTS ROHS FP / POLYIMIDE / FP TAPE FP TAPE SIZE 26 THROUGH 10 FP / POLYIMIDE / FP TAPE FP TAPE FP TAPE SIZE 8 THROUGH 6 FP / POLYIMIDE / FP TAPE FP TAPE FP TAPE FP TAPE SIZE 4 THROUGH 04 FP - FLUOR

19、OCARBON POLYMER MODIFIED POLYTETRAFLUOROETHYLENE (PTFE) CONDUCTOR - STRANDED NICKEL COATED COPPER FIGURE 1 - AS22759/187 CONFIGURATION AEROSPACE STANDARD AS22759/187 SHEET 3 OF 6 REV. B WIRE, ELECTRICAL, POLYTETRAFLUOROETHYLENE/POLYIMIDE INSULATED, SMOOTH SURFACE, NORMAL WEIGHT, NICKEL-COATED COPPER

20、 CONDUCTOR, 260 C, 600 VOLTS ROHS TABLE 1 - CONSTRUCTION DETAILS PART NO. 1/ WIRE SIZE CONDUCTOR 4/ FINISHED WIRE 3/ STRANDING (NUMBER OF STRANDS X SIZE GAUGE OF STRANDS) DIAMETER (IN) RESISTANCE AT 20 C (68 F) (OHMS/1000 FEET MAX) DIAMETER (IN) WEIGHT (LB/1000 FEET) 2/ MIN MAX MIN MAX MIN TARGET MA

21、X M22759/187-26-* M22759/187-24-* M22759/187-22-* M22759/187-20-* M22759/187-18-* M22759/187-16-* M22759/187-14-* M22759/187-12-* M22759/187-10-* M22759/187-8-* M22759/187-6-* M22759/187-4-* M22759/187-2-* M22759/187-1-* M22759/187-01-* M22759/187-02-* M22759/187-03-* M22759/187-04-* 26 24 22 20 18

22、16 14 12 10 8 6 4 2 1 0 00 000 0000 19 X 38 19 X 36 19 X 34 19 X 32 19 X 30 19 X 29 19 X 27 37 X 28 37 X 26 133 X 29 133 X 27 133 X 25 665 X 30 817 X 30 1045 X 30 1330 X 30 1665 X 30 2109 X 30 .0175 .0225 .0285 .0365 .0455 .0515 .0645 .0835 .106 .158 .198 .250 .320 .360 .395 .440 .500 .565 .0204 .02

23、44 .0314 .0394 .0494 .0554 .0694 .0894 .112 .169 .212 .268 .340 .380 .425 .475 .540 .605 42.2 25.9 16.0 9.77 6.10 4.76 3.00 1.98 1.24 .694 .436 .275 .177 .144 .113 .089 .071 .056 .033 .038 .043 .051 .061 .068 .081 .100 .122 .180 .219 .276 .344 .388 .420 .475 .530 .590 .037 .042 .047 .055 .065 .073 .

24、086 .105 .127 .188 .229 .288 .364 .408 .450 .505 .560 .630 1.29 1.87 2.70 4.25 6.35 8.10 12.3 19.0 30.0 57.5 89.7 141 217 265 335 419 533 646 1.42 2.04 2.90 4.45 6.60 8.40 12.8 19.7 30.8 59.4 92.2 145 225 274 349 438 548 667 1.55 2.20 3.10 4.65 6.85 8.70 13.3 20.2 31.6 61.3 94.7 149 233 283 363 457

25、563 688 1/ PART NUMBER: THE ASTERISKS IN THE PART NUMBER COLUMN OF TABLE 1 SHALL BE REPLACED BY THE COLOR CODE DESIGNATORS IN ACCORDANCE WITH MIL-STD-681. M22759/187-20-93 IS A 20 AWG WHITE WITH ORANGE STRIPE. 2/ THE ACCEPTABLE VALUE FOR THE CPK FOR THE FINISHED WIRE WEIGHT LISTED SHALL BE 1.3, USIN

26、G A NORMAL (GAUSSIAN) DISTRIBUTION TO OBTAIN THOSE CPK VALUES. 3/ THE WIRE CONSTRUCTION SHALL HAVE A SMOOTH POLYTETRAFLUOROETHYLENE (PTFE) OUTER LAYER WITH COMPLETE BONDING BETWEEN THE HOMOGENEOUS LAYERS. 4/ CONDUCTOR SHALL CONFORM TO AS29606 TYPE NCC SMALL DIAMETER NICKEL COATED COPPER CONDUCTOR FO

27、R WIRE SIZES 26 THROUGH 4 AND GENERAL PURPOSE FOR WIRE SIZES 2 THROUGH 0000. REQUIREMENT: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS22759. 1. WIRE CONSTRUCTION WIRE CONSTRUCTION SHALL BE IN ACCORDANCE WITH FIGURE 1 AND TABLES 1, 2, 3, AND 4. TABLE 2 - WIRE INSULATION

28、MATERIAL TAPE CODE THICKNESS (NOM) MATERIAL 1 .0020 .0005 (FP)/.0010 (POLYIMIDE)/.0005 (FP) 2 .0010 FP (SKIVED) 3 .0020 FP (SKIVED) 4 .0020 FP (UNSINTERED) 5 .0025 FP (UNSINTERED) 6 .0030 FP (UNSINTERED) AEROSPACE STANDARD AS22759/187 SHEET 4 OF 6 REV. B WIRE, ELECTRICAL, POLYTETRAFLUOROETHYLENE/POL

29、YIMIDE INSULATED, SMOOTH SURFACE, NORMAL WEIGHT, NICKEL-COATED COPPER CONDUCTOR, 260 C, 600 VOLTS ROHS TABLE 3 - TAPE OVERLAP REQUIREMENTS 1/ WIRE SIZE WRAP 1 WRAP 2 WRAP 3 WRAP 4 NOMINAL WALL THICKNESS (MILS) TAPE CODE PERCENT OVERLAP TAPE CODE PERCENT OVERLAP TAPE CODE PERCENT OVERLAP TAPE CODE PE

30、RCENT OVERLAP MIN MAX MIN MAX MIN MAX MIN MAX 26 1 50.5 54.0 4 50.5 54.0 7.4 24 1 50.5 54.0 4 50.5 54.0 7.4 22 1 50.5 54.0 4 50.5 54.0 7.4 20 1 50.5 54.0 4 50.5 54.0 7.4 18 1 50.5 54.0 4 50.5 54.0 7.4 16 1 50.5 54.0 5 50.5 54.0 8.3 14 1 50.5 54.0 5 50.5 54.0 8.3 12 1 50.5 54.0 6 50.5 54.0 9.1 10 1 5

31、0.5 54.0 6 50.5 54.0 9.1 8 2 20.5 35.0 1 50.5 55.0 6 67.0 71.0 13.2 6 2 20.5 35.0 1 50.5 55.0 6 67.0 71.0 13.2 4 3 20.5 35.0 1 50.5 55.0 6 50.5 54.0 6 50.5 54.0 16.2 2 3 20.5 35.0 1 50.5 55.9 6 50.5 54.0 6 50.5 54.0 16.2 1 3 20.5 35.0 1 50.5 55.0 6 50.5 54.0 6 50.5 54.0 16.2 1/0 3 20.5 35.0 1 50.5 5

32、5.0 6 50.5 54.0 6 50.5 54.0 16.2 2/0 3 20.5 35.0 1 50.5 55.0 6 50.5 54.0 6 50.5 54.0 16.2 3/0 3 20.5 35.0 1 50.5 55.0 6 50.5 54.0 6 50.5 54.0 16.2 4/0 3 20.5 35.0 1 50.5 55.0 6 50.5 54.0 6 50.5 54.0 16.2 1/ WRAP 1 IS THE INNERMOST TAPE WHICH IS IN CONTACT WITH THE CONDUCTOR. WRAPS 2, 3, AND 4 ARE PR

33、OGRESSIVELY FURTHER AWAY FROM THE CONDUCTOR CORE. 2. WIRE PERFORMANCE RATING: TEMPERATURE RATING: 260 C (500 F) MAXIMUM CONDUCTOR CONTINUOUS TEMPERATURE. VOLTAGE RATING: 600 VOLTS (RMS) AT SEA LEVEL. THIS INSULATION SYSTEM HAS BEEN USED IN AEROSPACE APPLICATIONS USING 115 VOLTS (PHASE TO NEUTRAL), 4

34、00 HERTZ AC AND 28 VOLTS DC. VERIFICATION OF THE SUITABILITY OF THIS PRODUCT FOR USE IN OTHER ELECTRICAL SYSTEM CONFIGURATIONS IS THE RESPONSIBILITY OF THE USER. 3. MATERIALS AND PHYSICAL PROPERTIES: SEE AS22759 FOR MATERIAL REQUIREMENT. MATERIALS USED IN THE MANUFACTURE OF THESE PRODUCTS SHALL COMP

35、LY WITH THE RESTRICTION OF HAZARDOUS SUBSTANCES DIRECTIVE 2002/95/EC. 4. FINISH WIRE INSULATION PROPERTIES: FINISH WIRE INSULATION PROPERTIES SHALL BE IN ACCORDANCE WITH TABLE 4. TABLE 4 - FINISHED WIRE INSULATION PROPERTIES REQUIREMENTS INSULATION PROPERTIES IMPULSE TEST VOLTAGE 8.0 KILOVOLTS (PEAK

36、) HIGH FREQUENCY TEST VOLTAGE 5.7 KILOVOLTS (RMS) INSULATION STATE OF SINTER 3.0 JOULES PER GRAM MAXIMUM WIRE SIZES 26 10 NOT REQUIRED FOR WIRE SIZES 8 AND LARGER TAPE OVERLAP TABLE 3 LAMINATION SEALING 260 C 2 C (500 F 3.6 F), 6 HOURS INSULATION BLOCKING 260 C 2 C (500 F 3.6 F) SHRINKAGE 290 C 2 C

37、(554 F 3.6 F) MAXIMUM CHANGE .091 INCHES WIRE SIZES 26 - 10 MAXIMUM CHANGE .125 INCHES WIRE SIZE 8 - 0000 ELECTRICAL RESISTANCE (IR) 5000 MEGOHMS (MIN)-1000 FEET WIRE SIZES 26 - 10 3000 MEGOHMS (MIN)-1000 FEET WIRE SIZES 8 - 0000 WET DIELECTRIC VOLTAGE 2500 VOLTS (RMS), 60 HERTZ INSULATION STRIP FOR

38、CE .25 - 6.0 POUNDS: WIRE SIZES 26 - 20 .50 - 7.0 POUNDS: WIRE SIZES 18 - 14 UV LASER MARKING 62% MINIMUM AVERAGE CONTINUOUS LENGTH SCHEDULE B AEROSPACE STANDARD AS22759/187 SHEET 5 OF 6 REV. B WIRE, ELECTRICAL, POLYTETRAFLUOROETHYLENE/POLYIMIDE INSULATED, SMOOTH SURFACE, NORMAL WEIGHT, NICKEL-COATE

39、D COPPER CONDUCTOR, 260 C, 600 VOLTS ROHS 5. FINISH WIRE IDENTIFICATION: WIRE IDENTIFICATION EXCEPTIONS: NONE WIRE IDENTIFICATION DURABILITY: 125 CYCLES (250 STROKES) WITH 250 GRAMS WEIGHT STRIPE AND BAND DURABILITY: 125 CYCLES (250 STROKES) WITH 250 GRAMS WEIGHT 6. FINISH WIRE PERFORMANCE: FINISH W

40、IRE FIXTURES APPLICABLE TO EACH WIRE SIZE SHALL BE IN ACCORDANCE WITH TABLE 5. TABLE 5 - TEST MANDREL AND TEST LOAD REQUIREMENTS WIRE SIZE (AWG) TEST MANDREL DIAMETER 1/ (INCHES) TEST LOAD (LB) COLD BEND LIFE CYCLE/ BEND TEST WRAP COLD BEND LIFE CYCLE/ BEND TEST 26 24 22 20 18 16 14 12 10 8 6 4 2 1

41、0 00 000 0000 1.00 1.00 1.00 1.00 1.50 1.50 2.00 2.00 3.00 4.00 5.00 6.00 8.00 10.00 10.00 12.00 18.00 18.00 .375 .500 .500 .500 .750 1.00 1.00 1.50 2.00 3.00 4.00 5.00 6.00 8.00 8.00 10.00 10.00 10.00 .125 .125 .125 .125 .250 .250 .375 .375 .375 .750 1.00 1.25 2.00 2.50 3.00 4.00 5.00 6.00 3.00 3.0

42、0 4.00 4.00 5.00 5.00 5.00 5.00 6.00 10.00 10.00 15.00 15.00 15.00 15.00 20.00 30.00 30.00 .50 .75 1.00 1.50 2.00 2.00 3.00 3.00 3.00 4.00 4.00 4.50 6.00 6.00 6.00 8.00 10.00 10.00 1/ TOLERANCE SHALL BE 3% OF THE GIVEN VALUES. AEROSPACE STANDARD AS22759/187 SHEET 6 OF 6 REV. B WIRE, ELECTRICAL, POLY

43、TETRAFLUOROETHYLENE/POLYIMIDE INSULATED, SMOOTH SURFACE, NORMAL WEIGHT, NICKEL-COATED COPPER CONDUCTOR, 260 C, 600 VOLTS ROHS FINISH WIRE PERFORMANCE CHARACTERISTICS SHALL BE IN ACCORDANCE WITH TABLE 6. TABLE 6 - FINISH WIRE PERFORMANCE CHARACTERISTICS PERFORMANCE CHARACTERISTIC REQUIREMENT MANDREL

44、BEND RESISTANCE (TAPES/BRAIDS) REQUIRED THERMAL SHOCK MECHANICAL RESISTANCE TEMPERATURE EXPOSURE 260 C 2 C (500 F 3.6 F) MAXIMUM CHANGE .091 INCHES WIRE SIZES 26 -10 MAXIMUM CHANGE .125 INCHES WIRE SIZE 8 - 0000 THERMAL MECHANICAL RESISTANCE (LIFE CYCLE) EXPOSURE 500 HOURS, 290 C 2 C (554 F 3.6 F) U

45、V LASER CONTRAST MARKING RESISTANCE AFTER THERMAL AGING: 168 HOURS HUMIDITY RESISTANCE (IR) 5000 MEGOHMS (MIN)-1000 FEET WIRE SIZES 26 - 10 3000 MEGOHMS (MIN)-1000 FEET WIRE SIZES 8 - 0000 FLUID RESISTANCE DIAMETER INCREASE 5% (MAX) SMOKE RESISTANCE 260 C 5 C (500 F 9 F) FLAME RESISTANCE SELF-EXTING

46、UISH TIME: 3 SECONDS BURN LENGTH 3 INCHES WET ARC RESISTANCE MINIMUM 70 WIRES PASS WET DIELECTRIC TEST 2 OR LESS WIRES FAIL IN ONE BUNDLE DAMAGE LENGTH: 1.0 INCHES OF LESS DRY ARC RESISTANCE MINIMUM 70 WIRES PASS WET DIELECTRIC TEST 2 OR LESS WIRES FAIL IN ONE BUNDLE DAMAGE LENGTH: 1.0 INCHES OF LES

47、S DYNAMIC CUT-THROUGH WIRE SIZE 26 10 POUNDS AT 23 C, 8 POUNDS AT 150 C, 6 POUNDS AT 200 C, 4 POUNDS AT 260 C WIRE SIZE 20 25 POUNDS AT 23 C, 20 POUNDS AT 150 C, 15 POUNDS AT 200 C, 10 POUNDS AT 260 C WIRE SIZE 16 25 POUNDS AT 23 C, 20 POUNDS AT 150 C, 15 POUNDS AT 200 C, 10 POUNDS AT 260 C FORCED H

48、YDROLYSIS INSULATION RESISTANCE WIRE SIZE 20 70 C 2 C (158 F 3.6 F), 5000 HOURS LONGEVITY RESISTANCE (THERMAL INDEX) 260 C 2 C (500 F 3.6 F), 10 000 HOURS ABRASION RESISTANCE (NEEDLE) WIRE SIZE 20 SAMPLE SIZE 8 READINGS 5000 MIN CYCLES, 23 C 2 C (73 F 3.6 F) 3000 MIN CYCLES, 70 C 2 C (158 F 3.6 F) 1

49、000 MIN CYCLES, 150 C 2 C (302 F 3.6 F) 7. REQUIREMENT EXCEPTION TO THE AS22759: NONE APPLICATION NOTES 1. PRODUCTS MANUFACTURED TO THIS SPECIFICATION ARE ROHS COMPLIANT. SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOC