SAE AS 24122-2004 WIRING HARNESS - EXTERNAL POWER 115 VOLT AC SINGLE PHASE《FSC6150 单相交流115 V外部电源线束 [代替 NAVY MS24122 版本C 中国民航 注意 3 NAVY MS24122 版本C 有效 注意 2 NAVY MS24122 版本 C 有效注意.pdf

1、 AEROSPACE STANDARD WIRING HARNESS - EXTERNAL POWER, 115 VOLT AC, SINGLE PHASE AS24122 ISSUED 2004-04CUSTODIAN: SAE AE-8/AE-8A FEDERAL SUPPLY CLASS6150 AS24122 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: MIL-C-7974NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS24122 (USA

2、F), REVISION C, NOTICE 2 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS24122 (USAF), REVISION C, NOTICE 2. ANY PART NUMBERS ESTABLIS

3、HED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RU

4、LES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATIO

5、N REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. SAE TechnicalStandards Board Rules provide that: “This report is published b

6、y SAE toadvance thestate of technical andengineering sciences.The use of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least ev

7、ery five yearsat which time it may be reaffirmed, revised, orcancelled. SAE invites yourwritten commentsandsuggestions. Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect

8、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org REAFFIRMED 20

9、09-09SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS24122 AEROSPACE STANDARD WIRING HARNESS - EXTERNAL POWER, 115 VOLT AC, SINGLE PHASE AS24122 AS24122SHEET 2 OF 2THIS MILITARY STANDARD IS APPROVED FOR USE BY DIRECTORATE OF EL

10、ECTRONIC SUPPORT 2750 ABW/ESP, DEPARTMENT OF THE AIR FORCE, AND IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE. 1/ JUMPER - SOCKET CONTACT “E“ TO SOCKET CONTACT “N“ WITH AWG NO. 14 WIRE. MATERIAL: PLUG - MOLDED TO CABLE - RUBBER OR SYNTHETIC RUBBER SUITABLE FOR OPE

11、RATION AT TEMPERATURES DOWN TO -65C. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED TOLERANCES ARE: FRACTIONS 1/64, DECIMALS .008. MS PART NO. LENGTH IN. FT 2 IN. AWG WIRE SIZE TERMINAL(2 REQD) MS24122-1 20 2 MS20659-133 MS24122-2 30 2 MS20659-133 MS24122-3 40 2 MS20659-133 MS24122-4 60 2 MS20659-133 MS24122-5 20 1/0 MS20659-135 MS24122-6 30 1/0 MS20659-135 MS24122-7 40 1/0 MS20659-135 MS24122-8 60 1/0 MS20659-135