SAE AS 29606-2014 Wire Electrical Stranded Uninsulated Copper Copper Alloy or Aluminum or Thermocouple Extension General Specification For《未绝缘铜 铜合金或者铝或者热电偶补偿的搓制电线 通用规格》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2014 SAE International All rights reserved. No part of this pub

3、lication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970

4、(outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS29606AEROSPACESTANDARDAS29606Issued 2014-06 Wire, Electrical, Stranded, Uninsulate

5、d Copper, Copper Alloy, or Aluminum, or Thermocouple Extension, General Specification For RATIONALESAE version of MIL-DTL-29606, which includes enhancements for quality assurance provisions and establishes qualification requirements for the coated copper and copper-alloy conductors furnished under t

6、he specification. 1. SCOPE This specification covers concentric lay stranded and rope-lay stranded round electrical conductor fabricated from copper, copper alloy or aluminum. This specification also covers thermocouple extension conductor fabricated from nickel/chromium or nickel/aluminum/manganese

7、. The conductors in this specification are suitable for use in insulated wires used in aerospace and other applications. 1.1 Classification Stranded conductors are classified herein. The classifications are as follows: Conductor Material Conductor Coating Conductor Stranding Conductor Dimensions 1.1

8、.1 Part or Identifying Number (PIN) PINS to be used for the wire acquired to this specification are created as in the following example: M29606 -20 -SCC -GPConductor Diameter Tolerance (See 1.1.1.4)Conductor Material and Coating (See 1.1.1.3)Conductor Size (See 1.1.1.2)Basic Part Number (See 1.1.1.1

9、)The above conductor is a size 20 conductor of silver coated annealed copper conductor with general purpose diameter control.SAE INTERNATIONAL AS29606 Page 2 of 35 1.1.1.1 Basic Part Number The conductor part number consists of the letter “M,” the basic number of the applicable specification and the

10、 applicable alpha-numeric characters formulated in the example (see 1.1.1). 1.1.1.2 Conductor Size A one- or two-digit designator from Table 4 is used to designate the conductor size. 1.1.1.3 Conductor Material and Coating Designator An alphabetic designator from Table 3 is used to designate the con

11、ductor material and conductor coating. 1.1.1.4 Conductor Diameter Tolerance The conductor diameter dimensional tolerance is designated as follows: GP - General Purpose (see Table 4) SD - Small Diameter (see Table 4) NOTE: The GP conductors are inactive for new design for copper and copper alloy cond

12、uctors. All conductors without a distinct diameter tolerance (GP or SD) are designated as general purpose (GP) diameter tolerance conductors. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this document to the extent specified herein. The latest issue of SAE publica

13、tions shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, superse

14、des applicable laws and regulations unless a specific exemption has been obtained. 2.1.1 U.S. Government Publications Available from DLA Document Services, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Tel: 215-697-6396, http:/quicksearch.dla.mil/.2.1.1.1 Federal Standard FED-STD-22

15、8 Cable and Wire, Insulated; Methods of Testing 2.1.1.2 Department of Defense Standards MIL-STD-202 Electronic and Electrical Component Parts MIL-STD-2223 Test Methods for Insulated Electric Wire SD-6 Provisions for Governing Qualification 2.1.1.3 Department of Defense Specifications MIL-C-3993 Copp

16、er and Copper-Base Alloy Mill Products; Packaging of SAE INTERNATIONAL AS29606 Page 3 of 35 2.1.2 Non-Government Publications 2.1.2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outsi

17、de USA), www.sae.org.AIR4487 Investigation of Silver Plated Conductor Corrosion (Red Plague) ARP6400 Recommended Practice for Processing and Handling Wire and Cable with Silver Plated Conductors and ShieldsAS9100 Quality Management Systems - Requirements for Aviation, Space and Defense Organizations

18、 2.1.2.2 ASQ Publications Available from American Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI 53203, Tel: 800-248-1946 (United States or Canada), 001-800-514-1564 (Mexico) or +1-414-272-8575 (all other locations), www.asq.org.ASQ Z1.4 Sampling Procedures and Tables for Inspection

19、 by Attributes 2.1.2.3 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM B230/B230M Aluminum 1350 - H19 Wire for Electrical Purposes (DoD adopted) ASTM B263 Determination of Cross-Sectiona

20、l Area of Stranded Conductors (DoD adopted) ASTM B286 Copper Conductors for Use In Hookup Wire for Electronic Equipment (DoD adopted) ASTM B298 Wire, Copper, Silver-Coated Soft or Annealed (DoD adopted) ASTM B355 Nickel-Coated Soft or Annealed Copper Wire (DoD adopted) ASTM B624 Wire Copper Alloy, H

21、igh Strength, High Conductivity, for Electronic Application (DoD adopted) ASTM B961 Standard Specification for Silver Coated Copper and Copper Alloy Stranded Conductors for Electronic Space Application ASTM B965 Standard Specification for High Performance Tin-Coated Annealed Copper Wire Intended for

22、 Electrical and Electronic Application for Solderability ASTM E230/E203M Standard Specification and Temperature Electromotive Force (EMF) Tables for Standardized Thermocouples2.1.2.4 TechAmerica Publications Available from TechAmerica, 1001 19th St. North, 20th Floor, Arlington, VA 22209, Tel: 202-6

23、82-9110, www.techamerica.org.EIA-557 Statistical Process Control Systems (DoD adopted) SAE INTERNATIONAL AS29606 Page 4 of 35 2.1.2.5 NCSL Publications Available from NCSL International, 2995 Wilderness Place, Suite 107, Boulder, CO 80301, Tel: 303-440-3339, www.ncsli.org.NCSL-Z540 Laboratories, Cal

24、ibration, and Measuring and Test Equipment. (DoD adopted) 2.1.2.6 IPC Publications Available from IPC 3000 Lakeside Drive, Suite 309S, Bannockburn, Illinois 60015-1249, Tel 847-615-7100, www.ipc.orgIPC/JEDEC J-STD-002 Solderability Tests for Component Leads, Terminations, Lugs, Terminals and Wires 2

25、.2 Definitions 2.2.1 CONCENTRIC LAY Concentric lay is defined as a central strand surrounded by one or more layers of helically wound strands. 2.2.2 LOT All the stranded conductors of one part number made under the same essential conditions, produced on a substantially continuous basis, and offered

26、for inspection at one time are considered a lot for purposes of sampling. 2.2.3 SAMPLE The sample is the group of sample units selected from the lot for the purpose of inspection. 2.2.4 SAMPLE UNIT The sample unit consists of a single piece of finished conductor of sufficient length to permit all ap

27、plicable examinations and tests. Not more than one sample unit for each group of tests should be taken from a single unit of product. 2.2.5 UNIT OF PRODUCT A unit is one continuous length of conductor. 2.2.6 QUALIFICATION INSPECTION Qualification inspection is a process that demonstrates that a comp

28、onent is capable of fully conforming to all the requirements defined in a standard. Qualification inspection includes definition of the measurements, tests, analysis, and associated data which provides consistent rationale for acceptance of a particular suppliers design as meeting the standard requi

29、rements typically prior to acquisition by the Purchaser. 2.2.7 QUALIFIED PRODUCTS LIST A Qualified Products List is a list of suppliers whose products have been evaluated to a defined standard using a defined process and who are authorized to provide those products to a purchaser upon request. When

30、a Qualified Products List is specified only approved suppliers are authorized to provide products under the part number defined in the component standard. A Qualified Products List is established and maintained by a Qualifying Activity. 2.2.8 QUALIFYING ACTIVITY A Qualifying Activity is a function e

31、stablished by an SAE specification that has a defined process used to consistently evaluate all suppliers products in accordance with the component standard. SAE INTERNATIONAL AS29606 Page 5 of 35 2.2.9 QUALITY CONFORMANCE INSPECTION Quality Conformance Inspection is a process which includes measure

32、ments, non-destructive test, analysis, and associated data that will provide verification that a particular individual component continually conforms to the requirements defined in the standard. 2.2.10 QUALIFICATION BY SIMILARITY An alternate Qualification Inspection process accomplished without com

33、pleting all of the measurements, test, and analysis requirements defined in the standard. Acceptance and the extent of similarity, is determined by the Qualifying activity. Similarity is established through a rationale that certain designs, materials, and/or processes are identical to those already

34、approved through qualification of the components. Verification testing for the new product is not required or reduced for designs, materials, and/or processes already approved. 2.2.11 PURCHASER A purchaser is an activity that can issue a purchase order or contract.2.2.12 SUPPLIER A supplier is an or

35、iginal component manufacturer or a value added component manufacturer (i.e. distributer, assembly plant, etc.) which has design and production control of the processes used to produce the final component in accordance with the standard. 2.2.13 QPL SOURCE In order to be considered for listing on a Qu

36、alified Products List (QPL), a supplier has to comply with the conditions listed below.1. The potential source has to have control of the engineering drawings for manufacturing the products. 2. The potential source has to do final inspection and shipping from the location to be listed on the QPL. 3.

37、 The potential source had to be responsible for all the initial and periodic qualification requirements identified in the specification.3. REQUIREMENTS 3.1 Qualification (see 4.4) The coated copper and copper-alloy conductors furnished under this specification shall be products, which are authorized

38、 by the qualifying activity for listing on the applicable qualified products list at the time set for opening of contract bids (see4.1 and 7.5.6) or purchase orders. Qualification requirements are in accordance with 4.4 herein. 3.1.1 Conformity to Qualified Sample It is understood that conductors su

39、pplied under contract shall be the same material formulations, material sources, and manufacturing processes as approved by the qualifying activity. Any unapproved changes made after the qualification approval date, unless accepted by the qualifying activity, may constitute cause for rejection. 3.2

40、Detail Specification The individual item requirements shall be as specified herein and in accordance with the ASTM document when applicable. In the event of any conflict between requirements of this specification and the ASTM standards (see 2.1.2), this specification shall govern. SAE INTERNATIONAL

41、AS29606 Page 6 of 35 3.3 Conductor Strand Material All strands used in conductors specified herein shall conform to the applicable ASTM standards for the proper material listed in Table 3. After stranding conductor, strands shall be free from lumps, kinks, splits, scraped or corroded surfaces, and s

42、kin impurities. In addition, the strands shall conform to the following requirements as applicable. 3.3.1 Tin Coated Copper Strands (Type TCC) Tin coating shall be in accordance with ASTM B965, except steam conditioning is not required for solderability testing. 3.3.2 Silver Coated Copper Strands 3.

43、3.2.1 Type SCC The strands shall have a coating thickness of not less than 40 micro-inches of silver when measured in accordance with ASTM B298.3.3.2.2 Type SCC1 The strands shall have a coating thickness of not less than 80 micro-inches of silver when measured in accordance with ASTM B298. After st

44、randing, the coating thickness on each of the individual conductor strands shall nowhere be less than 40 micro-inches of silver when inspected using micro-section analysis in accordance with ASTM B961.3.3.3 Nickel Coated Copper Strands (Type NCC) The strands shall have a coating thickness of not les

45、s than 50 micro-inches of nickel when measured in accordance with ASTM B355. 3.3.4 Heavy Nickel Coated Copper Strands (Type NHC) The copper strands shall have a coating thickness of not less than 27% by weight of nickel when measured in accordance with ASTM B355. 3.3.5 Silver Coated Copper Alloy Str

46、ands 3.3.5.1 Type SCA The copper alloy strand base material shall conform to ASTM B624. The strands shall have a coating thickness of not less than 40 micro-inches of silver when measured in accordance with ASTM B298.3.3.5.2 Type SCA1 The copper alloy strand base material shall conform to ASTM B624.

47、 The strands shall have a coating thickness of not less than 80 micro-inches of silver when measured in accordance with ASTM B298. After stranding, the coating thickness on each of the individual conductor strands shall nowhere be less than 40 micro-inches of silver when inspected using micro-sectio

48、n analysis in accordance with ASTM B961.3.3.6 Nickel Coated Copper Alloy Strands (Type NCA) The copper alloy strand base material shall conform to ASTM B624. The strands shall have a coating thickness of not less than 50 micro-inches of nickel when measured in accordance with ASTM B355. 3.3.7 Heavy

49、Nickel Coated Copper Alloy Strands (Type NHA) The copper alloy strand base material shall conform to ASTM B624. The copper strands shall have a coating thickness of not less than 27% by weight of nickel when measured in accordance with ASTM B355. SAE INTERNATIONAL AS29606 Page 7 of 35 3.3.8 Silver Coated Ultra-High Strength Copper Alloy Strands (Type SCU)The ultra-high strength copper alloy strands shall be made of a copper alloy mate