SAE AS 3078C-2014 FITTING INSERT FLUID CONNECTION MS33649 BOSS TO RING LOCKED BOSS《AS5202凸起到锁紧环凸台、液压连接插件》.pdf

1、AEROSPACE STANDARD FITTING, INSERT, FLUID CONNECTION, AS5202 BOSS TO RING LOCKED BOSS AS3078Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopy

2、ing, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1973-11REAFFIRMED2013-01REVISED

3、 2014-06THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B /8/ REV.CFEDERAL SUPPLY CLASS 4730 AS3078SHEET 1 OF 3REV. CPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis report

4、isentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE in

5、vites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3078CRATIONALE CORRECT WEIGHT VALUES AND UPDATE STANDARD. FIGURE 1 - INSERT TABLE 1A - DIMENSIONS BASIC NO. AS3078/16/SIZE CODE ATHREAD-3

6、BAS8879BTHREAD-3AAS8879 C D E+.005/-.002 F.003 G+.005/-.004 H+.005/-.004 02030405060810121620.3125-24UNJF .3750-24UNJF .4375-20UNJF .5000-20UNJF .5625-18UNJF .7500-16UNJF .8750-14UNJF 1.0625-12UNJ 1.3125-12UNJ 1.6250-12UNJ .4375-28UNJEF .5000-28UNJEF .5625-24UNJEF .6250-24UNJEF .6875-24UNJEF .9375-2

7、0UNJEF 1.0625-18UNJEF 1.2500-18UNJEF 1.5000-18UNJEF 1.8750-16UNJ .622 .685 .748 .810 .867 1.060 1.185 1.435 1.685 2.020 .602 .665 .728 .790 .852 1.040 1.165 1.415 1.665 1.978 .375 .440 .503 .566 .628 .858 .983 1.171 1.421 1.760 .469 .536 .599 .662 .724 .954 1.079 1.267 1.517 1.918 .544 .611 .672 .73

8、7 .801 1.029 1.172 1.362 1.612 2.012 .502 .569 .632 .695 .758 .988 1.122 1.310 1.560 1.961 AEROSPACE STANDARD AS3078SHEET 2 OF 3REV. CFITTING, INSERT, FLUID CONNECTION, AS5202 BOSS TO RING LOCKED BOSS TABLE 1B - DIMENSIONS AND WEIGHTS BASIC NO. AS3078/16/SIZE CODE J1.5 K L+.010/-.004 M+.010/-.005 N.

9、015 P LB/EAAPPROX LOCKRING BASIC NO. AS3077/7/SIZE CODE 0203040506081012162096.595.595.094.594.593.593.593.092.592.024283134364846546480.047.047.047.047.047.047.057.072.072.072.082.082.082.082.082.082.082.082.082.122.364.364.364.364.364.364.374.389.389.389.761 .729 .777 .802 .830 .955 1.051 1.185 1.

10、185 1.237 .025.033.034.041.045.087.113.155.211.32202030405060810121620NOTES: 1. MATERIAL: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, OR AMS5737 (UNS S66286). 2. HEAT TREATMENT: AMS5731 AND AMS5734 PARTS SHALL BE AGED IN ACCORDANCE WITH AMS-H-6875. HARDNESS 29 HRC MIN.3. FINISH: PA

11、SSIVATE AMS2700, TYPE 2 OR TYPE 8. /4/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT. 5. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417. 6. IDENTIFICATION PER AS478, CLASS 35D. NAME, TRADEMARK OR CAGE CODE AND PART NUMBER. /7/ INSERTS TO BE USED IN CONJUNCTION WITH AS3077 LOCKRI

12、NG AND TO BE INSTALLED PER AS1959 INTO BOSS CAVITIES PER AS1958. /8/ INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE“ MAY BE USED TO DEPLETION. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CH

13、ANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.

14、 11. INTERPRETATION OF DRAWING PER AS4296. 12. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra EXCEPT SEALING SURFACE TO BE 63 MICROINCHES Ra AND SERRATIONS TO BE 250 MICROINCHES Ra. 13. BREAK EDGES .003 T

15、O .015 UNLESS OTHERWISE SPECIFIED. 14. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 AEROSPACE STANDARD AS3078SHEET 3 OF 3REV. CFITTING, INSERT, FLUID CONNECTION, AS5202 BOSS TO RING LOCKED BOSS 15. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010. /16/ EXAMPLE OF PART NUMBER: