SAE AS 3119A-2013 Bolt Machine-Hexagon Head Drilled 6 Holes PD Shank CRES AMS 5731 500-20 UNJF-3A《机制螺栓 5000-20 UNJF-3A AMS5731耐蚀钢PD柄6钻孔的六角头》.pdf

1、AEROSPACE STANDARD (R) BOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, CRES AMS5731, .5000-20 UNJF-3A AS3119Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electron

2、ic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1979-0

3、7REAFFIRMED 2004-02 REVISED 2013-09THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS3119SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS7477SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. T

4、heuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabiliz

5、ed, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3119ARATIONALE DOCUMENT COMPLETELY REVISED THREAD SPEC CALLOUT CORRECTED AND DOCUMENT BROUGHT UP TO DATE. .846 MIN

6、.752.741KL.00332250.462.47232CHAMFER 30 TO .750A.5000-20 UNJF-3APER AS8879 MAXIMUM 2 INCOMPLETETHREADS (SEE NOTE 3) .760 MAX .710 MINBEARING SURFACEVIEW A ENLARGEDSECTION THRUTHREAD PROFILE32MARK PART NUMBERAND MANUFACTURERSIDENTIFICATION PERAS478 CLASS AR.020.030.023 BBAB.002 x L.006 AOPPOSITE SIDE

7、 OPTIONAL.020 C D6 HOLES .070 CSK TO 90 - .100C.264.344DEQUALLY SPACED.160 TO POINT .188 TODEPTH SHOWN45 10-+ .428G.016SHAPE IN THISAREA OPTIONALFIGURE 1 AEROSPACE STANDARD AS3119SHEET 2 OF 3REV. A(R) BOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, CRES AMS5731, .5000-20 UNJF-3A TABLE 1 - D

8、IMENSIONS PART NUMBER L G MIN K MAX APPROX MASS LB/100 AS3119 -14 1.438 .030 .188 11.39 AS3119 -15 1.500 .090 .250 11.70 AS3119 -16 1.562 .152 .312 12.01 AS3119 -17 1.625 .215 .375 12.32 AS3119 -18 1.688 .278 .438 12.62 AS3119 -19 1.750 .340 .500 12.93 AS3119 -20 1.812 .402 .562 13.24 AS3119 -21 1.8

9、75 .465 .625 13.55 AS3119 -22 1.938 .528 .688 13.85 AS3119 -23 2.000 .590 .750 14.16 AS3119 -24 2.125 .715 .875 14.77 AS3119 -25 2.250 .840 1.000 15.39 AS3119 -26 2.375 .965 1.125 16.00 AS3119 -27 2.500 1.090 1.250 16.62 AS3119 -28 2.625 1.215 1.375 17.23 AS3119 -29 2.750 1.340 1.500 17.85 AS3119 -3

10、0 2.875 1.465 1.625 18.46 AS3119 -31 3.000 1.590 1.750 19.08 AS3119 -32 3.125 1.715 1.875 19.69 AS3119 -33 3.250 1.840 2.000 20.30 AS3119 -34 3.375 1.965 2.125 20.92 AS3119 -35 3.500 2.090 2.250 21.53 AS3119 -36 3.625 2.215 2.375 22.15 AS3119 -37 3.750 2.340 2.500 22.76 AS3119 -38 3.875 2.465 2.625

11、23.38 AS3119 -39 4.000 2.590 2.750 23.90 AS3119 -40 4.125 2.715 2.875 24.61 AS3119 -41 4.250 2.840 3.000 25.22 AS3119 -42 4.375 2.965 3.125 25.83 AS3119 -43 4.500 3.090 3.250 26.45 AS3119 -44 4.625 3.125 3.375 27.06 AS3119 -45 4.750 3.340 3.500 27.68 AS3119 -46 4.875 3.465 3.625 28.29 AS3119 -47 5.0

12、00 3.590 3.750 26.91 AS3119 -48 5.125 3.715 3.875 29.52 AS3119 -49 5.250 3.840 4.000 30.14 AS3119 -50 5.375 3.965 4.125 30.75 AS3119 -51 5.500 4.090 4.250 31.37 AS3119 -52 5.625 4.215 4.375 31.98 AS3119 -53 5.750 4.340 4.500 32.60 AS3119 -54 5.785 4.465 4.625 33.21 AS3119 -55 6.000 4.590 4.750 33.83

13、 FOR SHORT BOLTS THREADED TO HEAD SEE AS9588. AEROSPACE STANDARD AS3119SHEET 3 OF 3REV. A(R) BOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, CRES AMS5731, .5000-20 UNJF-3A NOTES: 1. FOR PART NUMBERS AS3119-14 THRU AS3119-17 THE THREAD PD SHALL REPLACE DATUM B. 2. MATERIAL: CORROSION RESISTA

14、NT STEEL AMS5731. 3. MANUFACTURING SPECIFICATION: AS7477. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE

15、SPECIFIED. 7. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 8. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENI

16、ENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.