SAE AS 3129B-2014 PLUG EXPANSION - CRES 303 LONG STD AND 010 OVERSIZE DIAMETERS UNS S30300《膨胀插头 长整型303耐腐蚀钢(CRES) STD和 010超大型口径 UNS S30300》.pdf

1、AEROSPACE STANDARD PLUG, EXPANSION - CRES, 303, LONG; STD AND .010 OVERSIZE DIAMETERS, UNS S30300 AS3129Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanica

2、l, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1981-02REAFFIRMED 2

3、006-05 REVISED 2014-01THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS3129SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis re

4、port is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled

5、. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3129BRATIONALE THIS IS A LIMITED SCOPE REVISION. REVISED CLEANING REQUIREMENTS FOR CONFORMANCE TO AMS2700 OR ASTM A967/A967M. FIG

6、URE 1 TABLE 1A - PART NUMBERS AND DIMENSIONS STANDARD DIAMETERS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERSPART NUMBER /8/A APPROX MASSLB/100 AS3129-03 PLGA1567030A .1553-.1562 .069 AS3129-04 PLGA1877030 A .1866-.1875 .095 AS3129-05 PLGA2187030 A .2178-.2187 .139 AS3129-06 PLGA2507030 A .2491-.2

7、500 .207 AS3129-07 PLGA2817030 A .2803-.2812 .246 AS3129-08 PLGA3437030 A .3428-.3437 .430 AS3129-09 PLGA4067030 A .4053-.4062 .619 AS3129-10 PLGA4687030 A .4678-.4687 .828 AS3129-11 PLGA5317030 A .5303-.5312 1.061AS3129-12 PLGA6567030 A .6553-.6562 1.923 AEROSPACE STANDARD AS3129SHEET 2 OF 3REV. BP

8、LUG, EXPANSION - CRES, 303, LONG; STD AND .010 OVERSIZE DIAMETERS, UNS S30300 TABLE 1B - PART NUMBERS AND DIMENSIONS .010 OVERSIZE DIAMETERS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERSPART NUMBER /8/A APPROX MASSLB/100 AS3129-53 PLGA1667030A .1653-.1662 .085 AS3129-54 PLGA1977030A .1966-.1975 .1

9、16 AS3129-55 PLGA2287030A .2278-.2287 .171 AS3129-56 PLGA2607030A .2591-.2600 .250 AS3129-57 PLGA2917030A .2903-.2912 .282 AS3129-58 PLGA3537030A .3528-.3537 .496 AS3129-59 PLGA4167030A .4153-.4162 .711 AS3129-60 PLGA4787030A .4778-.4787 .949 AS3129-61 PLGA5417030A .5403-.5412 1.185AS3129-62 PLGA666

10、7030A .6653-.6662 2.171 TABLE 1C - PART NUMBERS AND DIMENSIONS AEROSPACE STANDARD PART NUMBER B NOM CNOM DE NOM FGNOM HAS3129-03 STD AND .010 OVERSIZE DIAMETERS, UNS S30300 9. USE WITH AS3130 PINS. SEE AIR3276 HOLE PREPARATION AND AIR3277 INSTALLATION PROCEDURES. 10. DIMENSIONING AND TOLERANCING: AS

11、ME Y14.5M-1994. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. SEE AS3586 FOR PLUG AND PIN SET OF PARTS. 13. AS, AIR, AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF TH

12、E USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL

13、 PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYI

14、NG THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.