SAE AS 3132B-2014 PIN EXPANSION - CRES 303 SHORT UNS S30300《膨胀销 UNS S30300短型303 CRES》.pdf

1、AEROSPACE STANDARD PIN, EXPANSION - CRES, 303, SHORT, UNS S30300AS3132Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or oth

2、erwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1981-02REAFFIRMED 2006-05 REVISED 2014-01THIRD ANGLE

3、PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS3132SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits

4、 applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments

5、andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3132BRATIONALE THIS IS A LIMITED SCOPE REVISION. REVISED CLEANING REQUIREMENTS (NOTE 3) FOR CONFORMANCE TO AMS2700 OR ASTM A967/A967M. FIGURE 1 TABLE 1 - PART NUMB

6、ERS AND DIMENSIONS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERS PART NUMBER /8/ANOM B NOM CMAXD NOM ENOM F NOM APPROX MASSLB/100 AS3132-01 PLGA0934030A .062 .069 .020 .0417 30 .056 .006 AS3132-02 PLGA1254030A .086 .095 .020 .0417 10 .087 .015AS3132-03 PLGA1564030A .078 .116 .032 .0417 13 .104 .02

7、0 AS3132-04 PLGA1874030A .114 .154 .040 .0417 10 .139 .054 AS3132-05 PLGA2184030A .145 .179 .040 .0417 (a) (a) .094 AS3132-06 PLGA2504030A .160 .212 .040 .0417 10 .196 .146AS3132-07 PLGA2814030A .193 .245 .040 .0313 10 .233 .241 AS3132-08 PLGA3434030A .216 .305 .060 .0156 10 .289 .415 AS3132-09 PLGA

8、4064030A .255 .363 .060 .0208 10 .350 .699AS3132-10 PLGA4684030A .285 .436 .060 .0208 10 .420 1.141 AS3132-11 PLGA5314030A .375 .494 .060 .0156 10 .479 1.937AS3132-12 PLGA6564030A .390 .598 .060 .0182 10 .581 2.967 (a) AS3132-05 HAS A .01 TO .02 RADIUS INSTEAD OF A CHAMFER. AEROSPACE STANDARD AS3132

9、SHEET 2 OF 2REV. BPIN, EXPANSION - CRES, 303, SHORT, UNS S30300 NOTES: 1. MATERIAL: 303 CRES BAR PER AMS5640, TYPE 1 (UNS S303000). 2. HEAT TREAT: PER AMS5640. 3. CLEANING: FINISHED PARTS SHALL BE DEGREASED AND PASSIVATED PER ASTM A967/A967M OR AMS2700. A SOLUTION CONTAINING SODIUM DICHROMATE AND NO

10、T LESS THAN 20% BY VOLUME OF NITRIC ACID MUST BE USED. A CITRIC ACID METHOD MAY BE USED AS AN ALTERNATIVE IF REQUESTED BY THE PROCURING ACTIVITY AND THE SUPPLIER AGREES. 4. PINS ARE PREWAXED TO AID DRIVING. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE S

11、PECIFIED, SURFACES TO BE 250 MICROINCHES Ra. 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 2 DEGREES. DIMENSIONS APPLY AFTER FINISH. /8/ MARK AS3132-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE

12、IN ACCORDANCE WITH AS478, METHOD 37. 9. USE WITH AS3131 PLUGS. SEE AIR3277 INSTALLATION PROCEDURES. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 11. DO NOT USE UNASSIGNED PART NUMBERS. 12. SEE AS3587 FOR PLUG AND PIN SET OF PARTS. 13. AS, AIR, AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME

13、IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE D

14、OCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92

15、555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.