SAE AS 31481A-2012 CONNECTOR PLUG ELECTRIC CRIMP TYPE LANYARD PUSH-PULL COUPLING SERIES 2 (CLASS E AND J)《系列2 (E和J类)推拉式连接器牵索压接式电插头连接器》.pdf

1、 AEROSPACE STANDARD CONNECTOR, PLUG, ELECTRIC, CRIMP TYPE, LANYARD, PUSH-PULL COUPLING, SERIES 2 (CLASS E AND J) AS31481Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect

2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004

3、-06REVISED 2012-01REAFFIRMED 2017-03THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS31481 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS81703 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering scie

4、nces. The useofthis reportisentirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichtime it may berevised, reaffirmed, st

5、abilized, or cancelled. SAEinvites your written comments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS31481A RATIONALE AS31481A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTIFICATION THE REQUIRE

6、MENTS FOR ACQUIRING THE COMPONENTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS81703 FIGURE 1 - AS31481 CLASS E CONNECTOR AEROSPACE STANDARD AS31481 SHEET 2 OF 3 REV. A CONNECTOR, PLUG, ELECTRIC, CRIMP TYPE, LANYARD, PUSH-PULL COUPLING, SERIES 2 (CLASS E AND J) NOT

7、E 1: COUPLING RING AND BALLS ARE SHOWN IN THE ENGAGED POSITION FOR CLARITY. THIS POSITION SHALL ONLY BE POSSIBLE WHEN ENGAGED TO THE RECEPTACLE. IN THE NORMAL POSITION THE FOLLOWING IS TRUE. A. THE VISUAL LOCK INDICATOR IS NOT IN VIEW. B. THE BALLS ARE RELEASED WHEN “E” EQUAL “C”. FIGURE 1 (CONTINUE

8、D) - AS31481 CLASS E CONNECTOR TABLE 1- FIGURE 1 CONFIGURATION SHELL SIZE (DASH #) A MAX B MAX C MIN D .006 AVG. E MIN F .5 G +.002 -.004 H .010 J MAX N .004 1/ K MAX 2/ INSERT ARRANGE. -3 1.261 .923 .444 .374 .391 30 .202 .344 .114 .310 .138 AS33698 -7 1.411 1.082 .579 .490 .526 22.5 .460 AS33699 -

9、12 1.531 1.172 .713 .630 .661 .600 AS33700 -19 1.681 1.328 .852 .770 .799 .740 AS33701 -27 1.826 1.473 1.007 .925 .954 .895 AS33702 -37 1.914 1.609 1.127 1.047 10.76 1.017 AS33703 1/ DEPTH OF VOID IN DISENGAGE POSITION 2/ MEASURED WITH SQUARE NOSE PIN HAVING BASIC DIAMETER OF MATING CONTACT AEROSPAC

10、E STANDARD AS31481 SHEET 3 OF 3 REV. A CONNECTOR, PLUG, ELECTRIC, CRIMP TYPE, LANYARD, PUSH-PULL COUPLING, SERIES 2 (CLASS E AND J) NOTE 1: FOR ADAPTOR, SEALING NUT, GROMMET, AND SLEEVE SEE AS31301. FIGURE 2 AS31481 CLASS J JACKET CABLE GLAND SEAL-WATERTIGHT FOR CLASS E CONNECTORS TABLE 2 FIGURE 2 C

11、ONFIGURATION SHELL SIZE (DASH #) L MAX X Y MAX MP MAX 2/ MIN MAX -3 3.088 .178 .210 .645 2.0 -7 4.072 .381 .413 .926 2.7 -12 4.538 .412 .444 .988 4.0 -19 4.572 .522 .554 1.113 5.5 -27 4.572 .600 .632 1.113 8.0 -37 4.603 .662 .694 1.176 12.0 1/ FOR ADAPTOR, SEALING NUT, GROMMET, AND SLEEVE SEE AS3130

12、1 2/ MAXIMUM CABLE WEIGHT IN POUNDS THAT CAN BE APPLIED IN THE DIRECTION INDICATED REQUIREMENTS 1. DIMENSIONS ARE IN INCHES IN ACCORDANCE WITH FIGURE 1, FIGURE 2, TABLE 1, AND TABLE 2. DIMENSION LOCATING TRUE POSITIONS ARE BASIC. TRUE POSITION TOLERENCES ARE IN ACCORDANCE WITH ANSI Y14.5. 2. PART NU

13、MBER EXAMPLE APPLICATION 1. AS31481 IS RECOMMENDED FOR REPLACEMENT ONLY AND NOT FOR NEW DESIGN. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.