SAE AS 3150A-2013 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD CLOSE TOLERANCE SHANK AMS4967 (UNS R56400) 160 KSI 3750-24 UNJF-3A《机械螺栓 AMS 4967 (UNS R56400) 160 KSI 3750-24 U.pdf

1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI .3750-24 UNJF-3A AS3150Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any

2、 form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS:

3、http:/www.sae.org ISSUED 1976-11REAFFIRMED 2006-05 REVISED 2013-06THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS3150SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS7461 /8/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of

4、technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time it

5、may berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3150ARATIONALE REVISE THREAD SPECIFICATION TO AS8879. REVISE LIGHTENING HOLE CO

6、NFIGURATION (ADD SECTION VIEW) TO ALLOW OPTIONAL SHAPE AT BOTTOM OF HOLE, DELETE .015 MAX RADIUS AT BASE OF WRENCH PAD, UPDATE FPI REQUIREMENTS, ADD SURFACE FINISH REQUIREMENTS TO BOLT HEAD, ADD AS3062 FOR THREAD RUNOUT, UPDATE TO ANSI Y14.5M-1982125, DELETE METRIC DIMENSIONS, UPDATE ANSI Y14.5-1973

7、 TO ANSI Y14.5M- 1982, GENERAL EDITORIAL UPDATE, REFERENCES UDATED AND FIGURE 1 REDRAWN. FIGURE 1 - BOLTAEROSPACE STANDARD AS3150SHEET 2 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI .3750-24 UNJF-3A TABLE 1 - PART NUMBERS AND DIM

8、ENSIONS PART NO. L GMINKMAXAPPROX. MASSLB/100 PART NO. L GMINKMAXAPPROX. MASSLB/100 AS3150-03 .838- .858 .105 .198 2.31 AS3150-45 3.462-3.482 2.729 2.822 7.01 AS3150-04 .900- .920 .167 .260 2.42 AS3150-46 3.525-3.545 2.792 2.885 7.12 AS3150-05 .962- .982 .229 .322 2.53 AS3150-47 3.588-3.608 2.855 2.

9、948 7.24 AS3150-06 1.025-1.045 .292 .385 2.64 AS3150-48 3.650-3.670 2.917 3.010 7.35 AS3150-07 1.088-1.108 .355 .448 2.76 AS3150-49 3.712-3.732 2.979 3.072 7.46 AS3150-08 1.150-1.170 .417 .510 2.87 AS3150-50 3.775-3.795 3.042 3.135 7.57 AS3150-09 1.212-1.232 .479 .572 2.98 AS3150-51 3.838-3.858 3.10

10、5 3.198 7.68 AS3150-10 1.275-1.295 .542 .635 3.09 AS3150-52 3.900-3.920 3.167 3.260 7.79 AS3150-11 1.338-1.358 .605 .698 3.21 AS3150-53 3.962-3.982 3.229 3.322 7.90 AS3150-12 1.400-1.420 .667 .760 3.32 AS3150-54 4.025-4.045 3.292 3.385 8.02 AS3150-13 1.462-1.482 .729 .822 3.43 AS3150-55 4.088-4.108

11、3.355 3.448 8.13 AS3150-14 1.525-1.545 .792 .885 3.54 AS3150-56 4.150-4.170 3.417 3.510 8.24 AS3150-15 1.588-1.608 .855 .948 3.64 AS3150-57 4.212-4.232 3.479 3.572 8.36 AS3150-16 1.650-1.670 .917 1.010 3.75 AS3150-58 4.275-4.295 3.542 3.635 8.47 AS3150-17 1.712-1.732 .979 1.072 3.86 AS3150-59 4.338-

12、4.358 3.605 3.698 8.58 AS3150-18 1.775-1.795 1.042 1.135 3.98 AS3150-60 4.400-4.420 3.667 3.760 8.69 AS3150-19 1.838-1.858 1.105 1.198 4.09 AS3150-61 4.462-4.482 3.729 3.822 8.80 AS3150-20 1.900-1.920 1.167 1.260 4.20 AS3150-62 4.525-4.545 3.792 3.885 8.92 AS3150-21 1.962-1.982 1.229 1.322 4.32 AS31

13、50-63 4.588-4.608 3.855 3.948 9.03 AS3150-22 2.025-2.045 1.292 1.385 4.43 AS3150-64 4.650-4.670 3.917 4.010 9.14 AS3150-23 2.088-2.108 1.355 1.448 4.54 AS3150-65 4.712-4.732 3.979 4.072 9.24 AS3150-24 2.150-2.170 1.417 1.510 4.65 AS3150-66 4.775-4.795 4.042 4.135 9.37 AS3150-25 2.212-2.232 1.479 1.5

14、72 4.76 AS3150-67 4.838-4.858 4.105 4.198 9.48 AS3150-26 2.275-2.295 1.542 1.635 4.88 AS3150-68 4.900-4.920 4.167 4.260 9.58 AS3150-27 2.338-2.358 1.605 1.698 4.99 AS3150-69 4.962-4.982 4.229 4.322 9.69 AS3150-28 2.400-2.420 1.667 1.760 5.10 AS3150-70 5.025-5.045 4.292 4.385 9.80 AS3150-29 2.462-2.4

15、82 1.729 1.822 5.22 AS3150-71 5.088-5.108 4.355 4.448 9.92 AS3150-30 2.525-2.545 1.792 1.885 5.33 AS3150-72 5.150-5.170 4.417 4.510 10.03 AS3150-31 2.588-2.608 1.855 1.948 5.44 AS3150-73 5.212-5.232 4.479 4.572 10.14 AS3150-32 2.650-2.670 1.917 2.010 5.55 AS3150-74 5.275-5.295 4.542 4.635 10.25 AS31

16、50-33 2.712-2.732 1.979 2.072 5.66 AS3150-75 5.338-5.358 4.605 4.698 10.37 AS3150-34 2.775-2.795 2.042 2.135 5.77 AS3150-76 5.400-5.420 4.667 4.760 10.48 AS3150-35 2.838-2.858 2.105 2.198 5.89 AS3150-77 5.462-5.482 4.729 4.822 10.59 AS3150-36 2.900-2.920 2.167 2.260 6.00 AS3150-78 5.525-5.545 4.792

17、4.885 10.70 AS3150-37 2.962-2.982 2.229 2.322 6.11 AS3150-79 5.588-5.608 4.855 4.948 10.81 AS3150-38 3.025-3.045 2.292 2.385 6.22 AS3150-80 5.650-5.670 4.917 5.010 10.92 AS3150-39 3.088-3.108 2.355 2.448 6.34 AS3150-40 3.150-3.170 2.417 2.510 6.45 AS3150-41 3.212-3.232 2.479 2.572 6.56 AS3150-42 3.2

18、75-3.295 2.542 2.635 6.67 AS3150-43 3.238-3.258 2.605 2.698 6.78 AS3150-44 3.400-3.420 2.667 2.760 6.90 AEROSPACE STANDARD AS3150SHEET 3 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, CLOSE TOLERANCE SHANK, AMS4967 (UNS R56400), 160 KSI .3750-24 UNJF-3A NOTES: /1/ FOR PART NUMBERS AS

19、3150-03 THRU AS3150-10 THE THREAD PD SHALL REPLACE DATUM B. 2. MATERIAL: TITANIUM ALLOY AMS4967 (SIMILAR TO UNS R56400) 3. PROCUREMENT SPECIFICATION: AS7461 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUI

20、REMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. /8/ HEAD TO SHANK FILLET SHALL BE COLD ROLLED PER AS7461 AFTER HEAT TREATMENT. THE COLD ROLLING SHALL BE SUFFICIENT TO REMOVE

21、ALL VISUAL EVIDENCE OF GRINDING OR TOOL MARKS EXCEPT THAT DISTORTIONS AT “A” IN FIGURE 2 OF THE SPECIFICATION SHALL NOT BE PERMITTED ON THE HEAD BEARING AREA AND SHALL BE PERMITTED ON THE SHANK DIAMETER ONLY IF THE DISTORTION DOES NOT CAUSE THE SHANK DIAMETER TO EXCEED .3750 DIAMETER. 9. DIMENSIONIN

22、G AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT

23、. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION