SAE AS 31571-2012 Insert Arrangements for AS81659 Series 1 and 2 Electrical Connectors《AS81659 系列1和2 电气连接器用嵌件部署》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS31571 AEROSPACE STANDARD AS31571 Issued 2012-08 Reaffirmed 2017-10 Supersedes MS3157 Insert A

5、rrangements for AS81659 Series 1 and 2 Electrical Connectors FSC 5935 RATIONALE AS31571 has been reaffirmed to comply with the SAE Five-Year Review policy. NOTICE The initial SAE publication of this document was taken directly from U.S. Military Standard MS3157D. This SAE Standard may retain the sam

6、e part numbers established by the original military document. Any requirements associated with Qualified Products Lists (QPL) may continue to be mandatory for DoD contracts. Requirements relating to QPLs have not been adopted by the SAE for this Standard and are not part of this SAE document. 1. SCO

7、PE 1.1 Scope This standard gives the dimensional requirements for insert arrangements used in AS81569 Series 1 and 2 electrical connectors. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this document to the extent specified herein. The latest issue of SAE publicati

8、ons shall apply. The applicable issue of the other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, super

9、sedes applicable laws and regulations unless a specific exemption has been obtained. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AS81659 Connectors, E

10、lectrical, Rectangular, Crimp Contacts, General Specification For 2.2 Order of Precedence In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regula

11、tions unless a specific exemption has been obtained. 2.3 Definitions The terms used in this standard are generally accepted by the electrical and electronics industries and commonly used in electrical connector engineering practice. 3. GENERAL REQUIREMENTS Not applicable. 4. DETAIL REQUIREMENTS 4.1

12、Dimensions Dimensions shall be in accordance with this standard and the following dimensional data: a. Dimensions are basic and are in inches. See AS81659 intermateability control dimensions for tolerance. b. Metric equivalents (to the nearest 0.01 mm) are given for general information only and are

13、based upon 1 in = 25.4 mm. c. Dimensions and markings shown are for engaging face of pin insert. Socket insert is opposite. 5. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 5.1 Intended Use This standard contains requirements

14、for insert arrangements to be used in AS815659 Series 1 and 2 Electrical Connectors. 5.2 Data Requirements No data is required by this standard. 5.3 Issue of DODISS When this standard is used in acquisition, the applicable issue of the DODISS must be cited in the solicitation. SAE INTERNATIONAL AS31

15、571 Page 2 of 14_ INSERTS FIGURE 1 - 26 POSITION INSERT ARRANGEMENT 26 SIZE 16 CONTACTS SHELL DESIGNATOR A SERVICE RATING B FIGURE 2 - 40 POSITION INSERT ARRANGEMENT 40 SIZE 20 CONTACTS SHELL DESIGNATOR A SERVICE RATING B SAE INTERNATIONAL AS31571 Page 3 of 14_ FIGURE 3 - 45 POSITION INSERT ARRANGEM

16、ENT 45 SIZE 20 CONTACTS SHELL DESIGNATOR A SERVICE RATING B FIGURE 4 - 57 POSITION INSERT ARRANGEMENT 57 SIZE 20 CONTACTS SHELL DESIGNATOR A SERVICE RATING B SAE INTERNATIONAL AS31571 Page 4 of 14_ FIGURE 5 - 67 POSITION INSERT ARRANGEMENT 64 SIZE 20 CONTACTS 3 SIZE 16 CONTACTS (POSTIONS 3, 4 AND 5)

17、 SHELL DESIGNATOR A SERVICE RATING A FIGURE 6 - 124 POSITION INSERT ARRANGEMENT 124 SIZE 20 CONTACTS SHELL DESIGNATOR B SERVICE RATING A SAE INTERNATIONAL AS31571 Page 5 of 14_ FIGURE 7 - 106 POSITION INSERT ARRANGEMENT 106 SIZE 22 CONTACTS SHELL DESIGNATOR A SERVICE RATING A FIGURE 8 - C2 POSITION

18、INSERT ARRANGEMENT 2 SIZE 1 COAX CONTACTS SHELL DESIGNATOR A SERVICE RATING A SAE INTERNATIONAL AS31571 Page 6 of 14_ FIGURE 9 - C3 POSITION INSERT ARRANGEMENT 2 SIZE 7 COAX CONTACTS (POSITIONS 1 AND 3) 1 SIZE 3 COAX CONTACT (POSITION 2) SHELL DESIGNATOR A SERVICE RATING A FIGURE 10 - C8 POSITION IN

19、SERT ARRANGEMENT 8 SIZE 9 COAX CONTACTS SHELL DESIGNATOR A SERVICE RATING A SAE INTERNATIONAL AS31571 Page 7 of 14_ FIGURE 11 - D8 POSITION INSERT ARRANGEMENT 4 SIZE 16 CONTACTS (POSITIONS 1, 2, 3 AND 4) 4 SIZE 12 CONTACTS (POSITIONS 5, 6, 7 AND 8) SHELL DESIGNATOR A SERVICE RATING B FIGURE 12 - 10C

20、3 POSITION INSERT ARRANGEMENT 7 SIZE 20 CONTACTS 3 SIZE 11 COAX CONTACTS (POSITIONS 5, 6, AND 7) SHELL DESIGNATOR A SERVICE RATING A SAE INTERNATIONAL AS31571 Page 8 of 14_ FIGURE 13 - 32C2 POSITION INSERT ARRANGEMENT 30 SIZE 20 CONTACTS 2 SIZE 5 COAX CONTACTS (POSITIONS A1 AND A2) SHELL DESIGNATOR

21、A SERVICE RATING A FIGURE 14 - 32C4 POSITION INSERT ARRANGEMENT 24 SIZE 20 CONTACTS, 4 SIZE 16 CONTACTS (POSITIONS 8, 9, 23 AND 24) 4 SIZE 9 COAX CONTACTS (POSITIONS 29, 30, 31 AND 32) SHELL DESIGNATOR A SERVICE RATING B SAE INTERNATIONAL AS31571 Page 9 of 14_ FIGURE 15 - 40C1 POSITION INSERT ARRANG

22、EMENT 39 SIZE 20 CONTACTS 1 SIZE 5 COAX CONTACTS (POSITION A1) SHELL DESIGNATOR A SERVICE RATING B FIGURE 16 - 33C4 POSITION INSERT ARRANGEMENT 25 SIZE 20 CONTACTS, 4 SIZE 16 CONTACTS (POSITIONS 1, 2, 3 AND 4) 4 SIZE 5 COAX CONTACTS (POSITIONS A1, A2, A3 AND A4) SHELL DESIGNATOR A SERVICE RATING A S

23、AE INTERNATIONAL AS31571 Page 10 of 14_ TABLE 1 - INSERT DESIGNATIONS INSERT DESIGNATION NUMBER SHELL INSERT PLACEMENT A B C D 0001 26P 0002 26S 0003 26P 26P 0004 26S 26S 0005 26P 26P 26P 0006 26S 26S 26S 0007 26P 26P 26P 26P 0008 26S 26S 26S 26S 0009 40P 0010 40S 0011 40P 40P 0012 40S 40S 0013 40P

24、40P 40P 0014 40S 40S 40S 0015 40P 40P 40P 40P 0016 40S 40S 40S 40S 0017 45P 0018 45S 0019 45P 45P 0020 45S 45S 0021 45P 45P 45P 0022 45S 45S 45S 0023 45P 45P 45P 45P 0024 45S 45S 45S 45S 0025 57P 0026 57S 0027 57P 57P 0028 57S 57S 0029 57P 57P 57P 0030 57S 57S 57S 0031 57P 57P 57P 57P 0032 57S 57S 5

25、7S 57S 0033 67P 0034 67S 0035 67P 67P 0036 67S 67S 0037 67P 67P 67P 0038 67S 67S 67S 0039 67P 67P 67P 67P 0040 67S 67S 67S 67S SAE INTERNATIONAL AS31571 Page 11 of 14_ TABLE 1 - INSERT DESIGNATIONS (CONTINUED) INSERT DESIGNATION NUMBER SHELL INSERT PLACEMENT A B C D 0041 106P 0042 106S 0043 106P 106

26、P 0044 106S 106S 0045 106P 106P 106P 0046 106S 106S 106S 0047 106P 106P 106P 106P 0048 106S 106S 106S 106S 0049 124P 0050 124S 0051 124P 124P 0052 124S 124S 0053 124P 124P 124P 0054 124S 124S 124S 0055 124P 124P 124P 124P 0056 124S 124S 124S 124S 0057 106S 26P 0058 106P 26S 0059 26P 106S 0060 26S 10

27、6P 0061 26P 26P 26P 26S 0062 26S 26S 26S 67P 0063 10C3P 10C3P C8P 67P 0064 10C3S 10C3S C8S 67S 0065 C8P C8P C8P 0066 C8S C8S C8S 0067 C8P C8P 106S 0068 C8S C8S 106P 0069 C8P 33C4P 0070 C8S 33C4S 0071 67P 106S 0072 67S 106P 0073 67P 67P C8P 0074 67S 67S C8S 0075 67P 67P 106S 0076 67S 67S 106P 0077 67

28、P 106S 33C4P 0078 67S 106P 33C4S 0079 67P 106S 67P 0080 67S 106P 67S SAE INTERNATIONAL AS31571 Page 12 of 14_ TABLE 1 - INSERT DESIGNATIONS (CONTINUED) INSERT DESIGNATION NUMBER SHELL INSERT PLACEMENT A B C D 0081 67P 67P 33C4P 33C4P 0082 67S 67S 33C4S 33C4S 0083 D8P 0084 D8S 0085 C8P C8P 67P 67P 00

29、86 C8S C8S 67S 67S 0087 106S C8P 0088 106P C8S 0089 106S 67P 0090 106P 67S 0091 106S 106S 67P 0092 106P 106P 67S 0093 106S 106S 33C4P 0094 106P 106P 33C4S 0095 106S C8P 106S 106S 0096 106P C8S 106P 106P 0097 106S 67P 106S C8P 0098 106P 67S 106P C8S 0099 106S 67P C8P C8P 0100 106P 67S C8S C8S 0101 10

30、6S 106S 67P 67P 0102 106P 106P 67S 67S 0103 33C4P 0104 33C4S 0105 33C4P 106S 0106 33C4S 106P 0107 33C4P C8P 0108 33C4S C8S 0109 C2P 40C1P 0110 C2S 40C1S 0111 C2P 57P 0112 C2S 57S 0113 C3P 67P 0114 C3S 67S 0115 C3P 106S 0116 C3S 106P 0117 C8P 106S 0118 C8S 106P 0119 10C3P 32C2P 0120 10C3S 32C2S 0121

31、32C2P 40C1P 0122 32C2S 40C1S SAE INTERNATIONAL AS31571 Page 13 of 14_ TABLE 1 - INSERT DESIGNATIONS (CONTINUED) INSERT DESIGNATION NUMBER SHELL INSERT PLACEMENT A B C D 0123 32C2P 45P 0124 32C2S 45S 0125 32C2P 57P 0126 32C2S 57S 0127 32C2P 67P 0128 32C2S 67S 0129 32C2P 106S 0130 32C2S 106P 0131 40C1

32、P 40C1P 0132 40C1S 40C1S 0133 57P 106S 0134 57S 106P 0135 C8P 0136 C8S 0137 10C3P 0138 10C3S 0139 32C2P 0140 32C2S 0141 40C1P 0142 40C1S 0143 67C3P 0144 67C3S 0145 C8P 57P 0146 C8S 57S 0147 57P 26P 0148 57S 26S 0149 32C4P 0150 32C4S 0151 32C4P 106S 0152 32C4S 106P 0153 67C3P 67C3P 32C4P 32C4P 0154 6

33、7C3S 67C3S 32C4S 32C4S 0155 C8P 32C4P 0156 C8S 32C4S 0157 106S 106S 32C4P 0158 106P 106P 32C4S 0159 32C4P C8P 0160 32C4S C8S 0161 67C3P 106S 32C4P 0162 67C3S 106P 32C4S 5.4 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not

34、 editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY SAE SUBCOMMITTEE AE-8C1, CONNECTORS OF COMMITTEE AE-8, AEROSPACE ELECTRICAL/ELECTRONIC DISTRIBUTION SYSTEMS STEERING GROUP SAE INTERNATIONAL AS31571 Page 14 of 14_