SAE AS 3230B-2015 RIVET - TUBULAR COUNTERSUNK CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N06600).pdf

1、 AEROSPACE STANDARD RIVET - TUBULAR, COUNTERSUNK, CORROSION AND HEAT RESISTANT NICKEL ALLOY(UNS N06600) AS3230Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mec

2、hanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1979-06REAFFI

3、RMED2012-11REVISED 2015-03THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.B FEDERAL SUPPLY CLASS 5320 AS3230 SHEET 1 OF 6 REV. B PROCUREMENT SPECIFICATION: AS7232SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theus

4、e ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orca

5、ncelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3230B RATIONALE THIS LIMITED SCOPE CHANGE UPDATES THE MATERIAL DESCRIPTION IN THE TITLE BLOCK AND DRAWING NOTE 1 TO ALIGN

6、WITH THE PROCUREMENT SPECIFICATION. FIGURE 1 AEROSPACE STANDARD AS3230 SHEET 2 OF 6 REV. B RIVET - TUBULAR, COUNTERSUNK, CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N06600) TABLE 1 AEROSPACE STANDARD AS3230 SHEET 3 OF 6 REV. B RIVET - TUBULAR, COUNTERSUNK, CORROSION AND HEAT RESISTANT NICKEL ALLO

7、Y (UNS N06600) TABLE 2 AEROSPACE STANDARD AS3230 SHEET 4 OF 6 REV. B RIVET - TUBULAR, COUNTERSUNK, CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N06600) TABLE 2 (CONTINUED) AEROSPACE STANDARD AS3230 SHEET 5 OF 6 REV. B RIVET - TUBULAR, COUNTERSUNK, CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N06

8、600) TABLE 2 (CONTINUED) AEROSPACE STANDARD AS3230 SHEET 6 OF 6 REV. B RIVET - TUBULAR, COUNTERSUNK, CORROSION AND HEAT RESISTANT NICKEL ALLOY (UNS N06600) NOTES: 1. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY PER AS7232 (UNS N06600). 2. G FOR DISTANCE OF .060 (1.52) FOR LENGTHS .188 (4.78)

9、AND SHORTER AND .100 (2.54) FOR LENGTHS LONGER THAN .188 (4.78). 3. PROCUREMENT SPECIFICATION: AS7232 4. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36. REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 250 MICROINCHES (6.3 MICROMETERS) Ra. 5. DIMENSIONING AND TOLERANCING: ANSI

10、Y14.5M-1982 6. DIMENSIONS IN INCHES (MILLIMETERS). METRIC CONVERSIONS IN PARENTHESES ARE IN INTERNATIONAL SYSTEM OF UNITS (SI). 7. BREAK SHARP EDGES .003 TO .015 (0.08 TO 0.38) UNLESS OTHERWISE SPECIFIED. 8. MARK MATERIAL CODE “EH2“ PER AS478-A-15A FOR 0.125 AND ABOVE. FOR 0.062 AND 0.094, MARK PART

11、 NUMBER AND MANUFACTURERS IDENTIFICATION PER AS478-37. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. AS IS A SAE INTERNATIONAL PUBLICATION 11. ANSI IS AN AMERICAN NATIONAL STANDARDS INSTITUTE PUBLICATION. 12. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING ARE

12、AS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.