SAE AS 3309B-2016 BOLT MACHINE C HEXAGON HEAD PD SHANK AMS5708 3750-24 UNJF-3A.pdf

1、AEROSPACE STANDARDBOLT, MACHINE HEXAGON HEAD,PD SHANK, AMS5708,.3750-24 UNJF-3AAS3309Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, rec

2、ording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED1985-08REAFFIRMED 2006-10REVISED2016-10THIR

3、D ANGLE PROJECTIONCUSTODIAN: E-25REV. BFEDERAL SUPPLY CLASS5306AS3309SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: AS7471SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis entirely voluntary, and

4、its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written commen

5、ts and suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS3309BRATIONALEFIGURE 1, BEARING SURFACE MINIMUM DIMENSION CORRECTED .FIGURE 1.017 A.631 MIN.564.553MARK PART NUMBER ANDMANUFACTURERS IDENTIFICATIONPER AS478 CLASS A.203.026.1

6、88.006R .025.01532KL32.003 ATHREAD RUNOUTPER AS3602250.3750-24 UNJF-3APER AS8879A .0025/1.006 BB.572 MAX .522 MIN BEARING SURFACEVIEW A ENLARGED32SECTION THRUTHREAD PROFILE.552.57210 - 20OR CHAMFERG45 APPROX.301.281.353.343/1/AAEROSPACE STANDARD AS3309 SHEET 2 OF 3 REV. B BOLT, MACHINE HEXAGON HEAD,

7、 PD SHANK, AMS5708, .3750-24 UNJF-3A TABLE 1 PART NUMBER L G MIN K MAX APPROX MASS LB/100 AS3309-03 .552 - .572 .025 .108 3.05 AS3309-04 .615 - .635 .025 .108 3.23 AS3309-05 .678 - .698 .025 .108 3.40 AS3309-06 .740 - .760 .025 .108 3.58 AS3309-07 .802 - .822 .025 .108 3.76 AS3309-08 .865 - .885 .02

8、5 .108 3.93 AS3309-09 .928 - w.948 .025 .108 4.11 AS3309-10 .990 - 1.010 .025 .108 4.28 AS3309-11 1.052 - 1.072 .025 .108 4.46 AS3308-12 1.115 - 1.135 .025 .125 4.64 AS3309-13 1.178 - 1.198 .045 .188 4.81 AS3309-14 1.240 - 1.260 .107 .250 4.99 AS3309-15 1.302 - 1.322 .169 .312 5.17 AS3309-16 1.365 -

9、 1.385 .232 .375 5.35 AS3309-17 1.428 - 1.448 .295 .438 5.53 AS3309-18 1.490 - 1.510 .357 .500 5.70 AS3309-19 1.552 - 1.572 .419 .562 5.88 AS3309-20 1.615 - 1.635 .482 .625 6.05 AS3309-21 1.678 - 1.698 .545 .688 6.23 AS3309-22 1.740 - 1.760 .607 .750 6.41 AS3309-23 1.802 - 1.822 .669 .812 6.58 AS330

10、9-24 1.865 - 1.885 .732 .875 6.76 AS3309-25 1.928 - 1.948 .795 .938 6.93 AS3309-26 1.990 - 2.010 .857 1.000 7.11 AS3309-27 2.115 - 2.135 .982 1.125 7.46 AS3309-28 2.240 - 2.260 1.107 1.250 7.81 AS3309-29 2.365 - 2.385 1.232 1.375 8.18 AS3309-30 2.490 - 2.510 1.357 1.500 8.53 AS3309-31 2.615 - 2.635

11、1.482 1.625 8.88 AS3309-32 2.740 - 2.760 1.607 1.750 9.23 AS3309-33 2.865 - 2.885 1.732 1.875 9.58 AS3309-34 2.990 - 3.010 1.857 2.000 9.94 AS3309-35 3.115 - 3.135 1.982 2.125 10.29 AS3309-36 3.240 - 3.260 2.107 2.250 10.64 AS3309-37 3.365 - 3.385 2.232 2.375 11.00 AS3309-38 3.490 - 3.510 2.357 2.50

12、0 11.35 AS3309-39 3.615 - 3.635 2.482 2.625 11.70 AS3309-40 3.740 - 3.760 2.607 2.750 12.06 AS3309-41 3.865 - 3.885 2.732 2.875 12.41 AS3309-42 3.990 - 4.010 2.857 3.000 12.76 AS3309-43 4.115 - 4.135 2.982 3.125 13.11 AS3309-44 4.240 - 4.260 3.107 3.250 13.46 AS3309-45 4.365 - 4.385 3.232 3.375 13.8

13、3 AS3309-46 4.490 - 4.510 3.357 3.500 14.18 AS3309-47 4.615 - 4.635 3.482 3.625 14.53 AS3309-48 4.740 - 4.760 3.607 3.750 14.88 AS3309-49 4.865 - 4.885 3.732 3.875 15.23 AS3309-50 4.990 - 5.010 3.857 4.000 15.59 AS3309-51 5.115 - 5.135 3.982 4.125 15.94 AS3309-52 5.240 - 5.260 4.107 4.250 16.29 AS33

14、09-53 5.365 - 5.385 4.232 4.375 16.65 AS3309-54 5.490 - 5.510 4.357 4.500 17.00 AS3309-55 5.615 - 5.635 4.482 4.625 17.36 AS3309-56 5.740 - 5.760 4.607 4.750 17.71 AS3309-57 5.865 - 5.885 4.732 4.875 18.06 AS3309-58 5.990 - 6.010 4.857 5.000 18.41 AEROSPACE STANDARD AS3309 SHEET 3 OF 3 REV. B BOLT,

15、MACHINE HEXAGON HEAD, PD SHANK, AMS5708, .3750-24 UNJF-3A NOTES 1. FOR PART NUMBERS AS3309-03 THROUGH AS3309-21 THE THREAD PD SHALL REPLACE DATUM -B-. 2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY AMS5708. 3. MANUFACTURING SPECIFICATION: AS7471. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM

16、E1417/E1417M TYPE 1. SENSITIVITY LEVEL 2 MINIMUM. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIM

17、ENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 5 DEGREES. 8. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DR

18、AWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED. 11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. A

19、N (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.