SAE AS 33703A-2010 INSERT ARRANGEMENTS ELECTRIC CONNECTOR SHELL SIZE 37《壳尺寸为37的电连接器插件布置》.pdf

1、AEROSPACE STANDARD INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 37 AS33703Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, record

2、ing, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2002-02REVISED 2010-06THIRD ANGLE PROJECTI

3、ON CUSTODIAN: SAE AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS33703SHEET 1 OF 4REV. APROCUREMENT SPECIFICATION: MIL-C-81703SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely volunt

4、ary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments a

5、ndsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS33703ARATIONALE REVISED TO PROVIDE LEGIBLE DRAWINGS NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS33703F, AMENDMENT 1, NOTICE 1, A

6、ND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS33703F, AMENDMENT 1, NOTICE 1,. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICAT

7、ION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLIC

8、ATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED

9、QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or network

10、ing permitted without license from IHS-,-,-AEROSPACE STANDARD AS33703SHEET 2 OF 4REV. AINSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 37 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE

11、 STANDARD AS33703SHEET 3 OF 4REV. AINSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 37 RECEPTACLES (REF) PLUGS (REF) MS3130 MS3137 MS3132 MS3138MS3134 MS3147MS3139 MS3148 MS3140 MS3446MS3143 MS3467MS3144 MS3468 MS3145 MS3445MS3149 MS3424MS3463MS3464 MS3466MS3469Copyright SAE International Provide

12、d by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS33703SHEET 4 OF 4REV. AINSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 37 DIMENSIONS IN INCHES. ANGLES IN DEGREES. TOLERANCES: DECIMALS .005. THIS IS A DESIGN ST

13、ANDARD. NOT TO BE USED AS A PART NUMBER. FOR DESIGN FEATURE PURPOSES THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. REFERENCES DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID. NOTES: 1. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONV

14、ENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-