SAE AS 34411A-2011 CONNECTOR PLUG ELECTRIC UTILITY《公用设施电插头连接器》.pdf

1、 AEROSPACE STANDARD CONNECTOR, PLUG, ELECTRIC, UTILITY AS34411Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

2、without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-06REVISED 2011-09REAFFIRMED 2017-03THIRD ANGLE PROJECTION

3、 CUSTODIAN: AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS34411 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: AS50151 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportisentirely voluntary, and its ap

4、plicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written comments a

5、nd suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS34411A RATIONALE AS34411A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS

6、SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS50151. FIGURE 1 - CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS34411 SHEET 2 OF 2 REV. A CONNECTOR, PLUG, ELECTRIC, UTILITY REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS50151. 1. DESIGN C

7、ONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1. DIMENSIONS ARE IN INCHES AND BASED ON FULLY TIGHTENED ACCESSORIES. TOLERANCES IN ACCORDANCE WITH ASME-Y14.5 -DIMENSIONING AND TOLERANCING. THE GROUNDING LUG SHALL BE INSTALLED ADJACENT TO PIN “D”. THE CABLE CLAMP SHALL COMFORM TO AS85049/41-12

8、A. 2. FINISH SHELL AND ACCESSORIES-OLIVE DRAB CHROMATE COATING OVER CADMIUM PLATE. 3. THE PART NUMBER SHALL BE AS SHOWN IN THE EXAMPLE BELOW: CONNECTOR PART NUMBER MS3441 A 20 - 4 P BASIC PART NUMBER CLASS SIZE INSERT ARRANGEMENT CONTACT STYLE (P ONLY) 4. MATING CONNECTOR THIS CONNECTOR SHALL MATE W

9、ITH MS3436-20-4S. NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. APPLICATION NOTES AS34411 IS NOT RECOMMENDED FOR NEW DESIGN AND IS NO LONGER RECOMMEDED FOR USE, EXCEPT FOR REPLACEMENT

10、PURPOSES. SPECIFICATION NOTES A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.