SAE AS 34561A-2011 CONNECTORS PLUG ELECTRICAL REAR RELEASE CRIMP CONTACT AN TYPE《AN型压接接触件后释放电缆连接电插头连接器》.pdf

1、 AEROSPACE STANDARD CONNECTORS, PLUG, ELECTRICAL, REAR RELEASE, CRIMP CONTACT, AN TYPE AS34561Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoco

2、pying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1998-07REVISED 2011-12REAFFIRM

3、ED 2017-03THIRD ANGLE PROJECTION CUSTODIAN: AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS34561 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS50151 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis report

4、isentirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SA

5、Einvites your written comments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS34561A RATIONALE AS34561A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIB

6、ED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS50151. FIGURE 1 CONNECTOR CONFIGURATION (CLASSES K, L,U & W EVIRONMENT RESISTANT) AEROSPACE STANDARD AS34561 SHEET 2 OF 3 REV. A CONNECTORS, PLUG, ELECTRICAL, REAR RELEASE, CRIMP CONTACT, AN TYPE TABLE 1 DIMENSIONS REQ

7、UIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS50151. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016. DIMENSIONS AND TOLERANCING SHALL BE IN AC

8、CORDANCE WITH ANSI/ASME Y14.5M-1994. AS50151 FRONT AND REAR RELEASE CRIMP CONTACT CONNECTORS AND SOLDER CONTACT CONNECTORS ARE INTERMATEABLE. UNLESS OTHERWISE SHOWN, CORRESPONDING FEATURES OF PIN AND SOCKET CONTACT CONNECTORS ARE IDENTICAL. EXTRACTION TOOL MIL-I-81969/29-01 SHALL BE USED TO REMOVE S

9、IZE 16 CONTACTS THAT ARE CRIMPED TO MIL-DTL-25038/1 FIRE ZONE WIRE. 2. FOR INSERT ARRANGEMENTS SEE MIL-STD-1651. SIZE L MAX. Q MAX. SIZE 16 & 12 CONTACTS SIZE 8, 4 & 0 CONTACTS 8 S 2.031 N/A .844 10 S .969 10 SL .969 12 S 1.062 12 2.125 1.062 14 S 2.031 1.156 14 2.125 1.156 16 S 2.031 1.250 16 2.125

10、 2.500 1.250 18 1.344 20 1.469 22 1.594 24 1.719 28 1.969 32 2.219 36 2.469 40 2.719 44 2.969 48 3.219 AEROSPACE STANDARD AS34561 SHEET 3 OF 3 REV. A CONNECTORS, PLUG, ELECTRICAL, REAR RELEASE, CRIMP CONTACT, AN TYPE 3. THE PART NUMBERS SHALL BE AS SHOWN IN THE EXAMPLE BELOW: NOTES: NOTICE THIS DOCU

11、MENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. SPECIFICATION NOTES: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL C

12、HANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.

13、APPLICATION NOTES: 1. AS34561 CLASSES K AND U ARE NOT RECOMMENDED FOR NEW DESIGN AND ARE NO LONGER RECOMMENDED FOR USE, EXCEPT FOR REPLACEMENT PURPOSES. CLASSES L AND W ARE RECOMMENDED FOR NEW DESIGN. 2. AS34561 SUPERSEDES MS3456. BASIC PART NO. CLASS K, L, U, W MATERIAL DESIGNATOR S-STAINLESS STEEL

14、. T-FERROUS ALLOY WITH CADMIUM PLATE. LEAVE BLANK FOR ALUMINUM ALLOY, WROUGHT ALUMINUM, AND FERROUS ALLOY WITH ELECTROLESS NICKEL FINISH. (FERROUS ALLOY NOT RECOMMENDED FOR NEW DESIGN) SHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR ALTERNATE INSERT POSITION W, X, Y OR Z. LEAVE BLANK FOR NORMAL POSITION MS3456 L 18 5 S W