SAE AS 34661A-2010 CONNECTOR RECEPTACLE ELECTRIC HERMETIC SOLDER TYPE BOX MOUNTING PUSH-PULL COUPLING SERIES 3 (CLASS H)《系列3(H级)推拉耦合盒装式焊接型密封电气插座连接器》.pdf

1、AEROSPACE STANDARD CONNECTOR, RECEPTACLE, ELECTRIC, HERMETIC,SOLDER TYPE, BOX MOUNTING, PUSH-PULL COUPLING, SERIES 3 (CLASS H) AS34661Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by an

2、y means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.

3、org ISSUED 2004-06REVISED 2010-12THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS34661SHEET 1 OF 4REV. APROCUREMENT SPECIFICATION: AS81703SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering scie

4、nces. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, o

5、rcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS34661ARATIONALE REVISION REQUIRED TO INCORPORATE AS34661-1A, CLARFY A DRAWING, AND UPDATE REFERENCES NOTICE THE REQUIRE

6、MENTS FOR ACQUIRING THE COMPONENTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS81703 FIGURE 1 AS34661 CONFIGURATION Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

7、AEROSPACE STANDARD AS34661SHEET 2 OF 4REV. ACONNECTOR, RECEPTACLE, ELECTRIC, HERMETIC, SOLDER TYPE, BOX MOUNTING, PUSH-PULL COUPLING, SERIES 3 (CLASS H) FIGURE 1 (CONTINUED) AS34661 CONFIGURATION Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or netwo

8、rking permitted without license from IHS-,-,-AEROSPACE STANDARD AS34661SHEET 3 OF 4REV. ACONNECTOR, RECEPTACLE, ELECTRIC, HERMETIC, SOLDER TYPE, BOX MOUNTING, PUSH-PULL COUPLING, SERIES 3 (CLASS H) TABLE 1 CONNECTOR DIMENSIONS AND WEIGHTS SHELLSIZE B C D F G J K L3 .392 .385.367.356.330 .441 .431.54

9、9.529.399.391.625 .891 7 .527 .520.483.473.451 .576 .566.682.662.534.526.719 1.016 12 .661 .654.624.614.553 .710 .700.822.802.669.661.813 1.109 19 .800 .793.763.753.738 .849 .839.947.927.807.799.906 1.203 27 .955 .948.918.908.854 1.004 .9941.130 1.110 .962.954.968 1.297 37 1.077 1.070 1.040 1.030 .9

10、78 1.126 1.116 1.228 1.208 1.084 1.076 1.187 1.453 61 1.365 1.358 1.316 1.306 1.271 1.414 1.404 1.510 1.490 1.367 1.360 1.436 1.797 TABLE 1 (CONTINUED) CONNECTOR DIMENSIONS AND WEIGHTS SHELLSIZEM WEIGHT (LBS) SEE NOTE 7 PIN INSERT 3 .583 (WEIGHT WILL BE 7 .760 SUPPLIED IN LATER 12 .885 REVISION) 19

11、1.010 27 1.141 37 1.271 61 1.583 TABLE 2 KEYWAY POSITIONS SIZE AA BB CC DD 3 23 97 187 - 7 23 97 187 27712 30 105 195 27019 30 105 195 27027 30 105 195 27037 30 105 195 27061 30 105 195 270Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking p

12、ermitted without license from IHS-,-,-AEROSPACE STANDARD AS34661SHEET 4 OF 4REV. ACONNECTOR, RECEPTACLE, ELECTRIC, HERMETIC, SOLDER TYPE, BOX MOUNTING, PUSH-PULL COUPLING, SERIES 3 (CLASS H) TABLE 3 CONTACT DIMENSIONS CONT SIZEEE GG HH JJ KK 20 .041 .039.088.061.058.052.188.109.110.06816 .0635 .0615

13、 .116.096.078.072.251.172.141.10912 .095 .093.150.130.122.110.251.172.143.109NOTES: (NOTES 1 THRU 6 APPLICABLE TO CONTACTS ONLY). 1. CONTACT FINISH: GOLD PLATE .000050 INCH MIN IN ACCORDANCE WITH ASTM B 488. A SUITABLE UNDERPLATING MAY BE USED. SILVER UNDERPLATING SHALL NOT BE USED. FINISH IS APPLIE

14、D AFTER SEALING. 2. DIMENSIONS IN INCHES, DIMENSIONS APPLY AFTER PLATING. 3. 63 ALL OVER PER ASME-B46.1-1962 UNLESS OTHERWISE SPECIFIED. 4. REMOVE ALL BURRS AND SHARP EDGES .003 TO .005 R. 5. DIAMETERS TO BE CONCENTRIC WITHIN .004 TIR. 6. DIAMETERS IN THE SAME CROSS-SECTIONAL PLANE TO BE CONCENTRIC

15、WITH EACH OTHER WITHIN .003 TIR. 7. WEIGHT LISTED IS CONNECTOR MAXIMUM WEIGHT PER SHELL SIZE 8. SHELL MATERIAL: COLD ROLLED STEEL, PER QQ-S-637. 9. SHELL FINISH: .0001 MIN. TIN PER ASTM B545, OVER NICKEL PER AMS-QQ-N-290. 10. EACH CONNECTOR SHALL BE PACKAGED WITH A PLASTIC DUST CAP OVER EACH END OF

16、SHELL. 11. FOUR KEYWAYS (MMC) AND INSERT SHALL BE LOCATED WITHIN .004 EITHER SIDE OF (TP) RELATIVE TO MASTER KEYWAY (MMC) AND SHELL O.D. (MMC). 12. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES SHALL BE .XX .010 AND .XXX .005; ANGULAR TOLERNACE, X DEGREES 1 DEGREES, 0 AND X DEGREE

17、S X 30. 13. DIAMETERS SHOWN ARE AT BASE OF BARRIERS. 14. PART NUMBER EXAMPLE MS34666 H 7 Y 50 P BI I I I I I I I I I I I I I_ ALTERNATE INSERTION POSITIION I I I I I I_ CONTACT STYLE (P-PIN) I I I I I_ INSERT ARRANGEMENT I I I I_ TERMINATION TYPE AND SHELL MATERIAL I I I_ _ SHELL SIZE I I_ CLASS I_

18、AS34661 BASIC PART NUMBER 15. APPLICATION NOTES AS34661 IS INACTIVE FOR NEW DESIGN AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. AS34461 SUPERSEDE MS3466 A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIA

19、L CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-