SAE AS 34801-2004 TOOL CONNECTOR ASSEMBLY FOR MIL-C-5015 CONNECTORS《MIL-C-5015标准连接器用接插件工具》.pdf

1、 AEROSPACE STANDARD TOOL, CONNECTOR ASSEMBLY, FOR MIL-C-5015 CONNECTORS AS34801Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recordin

2、g, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-06REAFFIRMED 2012-01THIRD ANGLE PROJECT

3、ION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5120 AS34801 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applica

4、bility and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsugge

5、stions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS34801 RATIONALE AS34801 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION M

6、S3480(NAVY) AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS3480(NAVY). ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REM

7、AIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION O

8、F PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFI

9、ED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT. AEROSPACE STANDARD AS34801 SHEET 2 OF 3 TOOL, CONNECTOR ASSEMBLY, FOR MIL-C-5015 CONNECTORS AEROSPACE STANDARD AS34801

10、SHEET 3 OF 3 TOOL, CONNECTOR ASSEMBLY, FOR MIL-C-5015 CONNECTORS DASH NUMBER CONNECTOR SHELL SIZE A THREAD CLASS 2A B .060 C APPROX D APPROX E DIA -.000 +.015 F DIA MIN G DIA -.015 +.000 H -.015 +.000 J MIN -08 8S 1/2-28 UNEF .365 .252 .370 .130 -10 10S,10SL 5/8-24 .718 .687 .440 .323 .448 .165 .375

11、 -12 12,12S 3/4-20 .555 .450 .557 .224 -14 14,14S 7/8-20 1.250 .675 .526 .682 .263 -16 16,16S 1 -20 .805 .651 .807 .325 -18 18 1 1/8-18 .930 .776 .932 .385 -20 20 1 1/4-18 1.050 .932 1.058 .463 -22 22 1 3/8-18 1.175 1.026 1.182 .510 -24 24 1 1/2-18 UNEF 2.000 1.300 1.151 1.307 .573 -28 28 1 3/4-18 U

12、NS 1.520 1.370 1.526 .683 -32 32 2 -18 UNS 1.770 1.620 1.776 .808 -36 37 2 1/4-16 UN 1.980 1.838 1.995 .915 -40 40 2 1/2-16 UN 2.750 .921 .750 2.220 2.058 2.245 1.023 .625 REQUIREMENTS: 1. TOOLS ARE FOR USE WITH CONNECTORS CONFORMING TO MIL-C-5015. 2. PART NUMBER SHALL INCLUDE: MS PART NUMBER AND DA

13、SH NUMBER AS SHOWN IN THE EXAMPLE BELOW. MS3480 - 28 MS NUMBER _ _ DASH NUMBER NOTES: 1. MATERIAL: a. SHELL; STEEL STANDARD QUALITY. b. HANDLE; DIE CAST ALUMINUM ALLOY PER QQ-A-591. 2. FINISH: NICKEL PLATE PER QQ-N-290. 3. REMOVE ALL BURRS AND SHARP EDGES. 4. ALL DIMENSIONS ARE INCHES. UNLESS OTHERW

14、ISE SPECIFIED, TOLERANCES: FRACTIONS 1/16, DECIMALS .016. 5. THREADS SHALL BE IN ACCORDANCE WITH HANDBOOK H28. FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID.