SAE AS 3535B-2014 NUT SELF-LOCKING SHANK UNS N07001 SILVER PLATE UNJ THREAD.pdf

1、AEROSPACE STANDARD NUT, SELF-LOCKING, SHANK, UNS N07001 SILVER PLATE, UNJ THREAD AS3535Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

2、recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1994-11REAFFIRMED 2012-11REVISED2014-

3、09THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5310 AS3535SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: AS7253SAE Technical Standards Board Rules provide that: “This report is publishedbySAEtoadvance thestateoftechnical and engineeringsciences. The useofthis reportisentirely volun

4、tary, and its applicabilityand suitability for any particularuse, includingany patent infringement arising therefrom, isthe soleresponsibility of the user.”SAE reviews each technical report at least every five years at whichtime it mayberevised, reaffirmed, stabilized, or cancelled. SAE invites your

5、 writtencomments and suggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3535BRATIONALE THIS LIMITED SCOPE REVISION DELETES DIAMETER SYMBOLS () FOR DIMENSIONS B AND C FROM TABLE 1A HEADING.FIGURE 1 AEROSPACE STANDARD A

6、S3535SHEET 2 OF 2REV. BNUT, SELF-LOCKING, SHANK, UNS N07001 SILVER PLATE, UNJ THREAD TABLE 1 DIMENSIONS TABLE 1A - DIMENSIONS A-W PARTNO. THREADTA+.005-.010 B+.005C+.004D +.003-.002 F +.002W +.010AS3535-02 .1640-36UNJF-3B .233 .368 .259 .171 .211 .442 AS3535-03 .1900-32UNJF-3B .257 .394 .285 .197 .2

7、37 .468 AS3535-04 .2500-28UNJF-3B .406 .450 .371 .266 .331 .625 AS3535-05 .3125-24UNJF-3B .468 .480 .401 .328 .394 .625 AS3535-06 .3750-24UNJF-3B .500 .600 .475 .401 .468 .750 TABLE 1B - DIMENSIONS K-J NOTES: 1. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY, AMS5706 OR AMS5708 (UNS N07001). 2.

8、 HEAT TREATMENT: SOLUTION, STABILIZATION, AND PRECIPITATION HEAT TREATED; SEE AMS5706 OR AMS5708. 3. HARDNESS: 32 TO 42 HRC 4. ANNEALING OF SHANK (F) PERMISSIBLE AT 1800 F MAXIMUM. IF ANNEALED, HARDNESS OF ADJACENT THREAD SHALL BE 32 HRC MINIMUM. 5. FINISH: SILVER PLATE THREADS PER AMS2411. PLATING

9、ON OTHER SURFACES OPTIONAL AND MAY BE INCOMPLETE. SEE PROCUREMENT SPECIFICATION FOR THICKNESS REQUIREMENTS. DIMENSIONS ARE AFTER PLATING. PARTIAL COVERAGE ON THREAD COUNTERSINKS PERMISSIBLE. 6. FLUORESCENT PENETRANT INSPECTION: PER ASTM E1417 BEFORE PLATING. ACCEPTANCE CRITERIA PER AS3071. 7. PROCUR

10、EMENT SPECIFICATION: AS7253. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 9. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 10. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION). 11. DI

11、MENSIONS ARE IN INCHES. 12. FOR PARTICULARS OF ATTACHMENT FLANGE HOLE AND ABUTMENT SHOULDER, REFER TO AS4847. FOR INSTALLATION OR REMOVAL OF SHANK NUTS, REFER TO ARP4848. 13. DO NOT USE UNASSIGNED PART NUMBERS. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOC

12、ATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.