SAE AS 3554B-2015 NUT SELF-LOCKING DOUBLE HEXAGON SILVER PLATED REDUCED HEIGHT 180 KSI 1400 UNS N07001.pdf

1、AEROSPACE STANDARDNUT, SELF-LOCKING, DOUBLE HEXAGON,SILVER PLATED, REDUCED HEIGHT180 KSI, 1400 F, UNS N07001AS3554Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic,

2、mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED1995-10REAFFIR

3、MED 2012-11REVISED2015-09THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV. BFEDERAL SUPPLY CLASS5310AS3554SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: AS7253SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis repo

4、rtis entirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. S

5、AEinvites your written comments and suggestions.SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3554BRATIONALETHIS IS A LIMITED SCOPE REVISION. IN DRAWING NOTE 6, UPDATE FPI REFERENCE AND REVISE SENSITIVITY LEVEL REQUIREMENT TO

6、 A MINIMUM LEVEL.FIGURE 1AEROSPACE STANDARD AS3554SHEET 2 OF 3REV.BNUT, SELF-LOCKING, DOUBLE HEXAGON,SILVER PLATED, REDUCED HEIGHT180 KSI, 1400 F, UNS N07001TABLE 1APARTNUMBERDTHREADBNOMDASHNO.EMAXFMIN ABHMINKMAXAS3554-09AS3554-10AS3554-11AS3554-12AS3554-13AS3554-14AS3554-15AS3554-16AS3554-17.190-32

7、 UNJF-3B.250-28 UNJF-3B.3125-24 UNJF-3B.375-24 UNJF-3B.4375-20 UNJF-3B.500-20 UNJF-3B.5625-18 UNJF-3B.625-18 UNJF-3B.750-16 UNJF-3B.2500.3125.3750.4375.5625.6250.6875.7812.9375081012141820222530.340.450.525.600.690.780.880.9701.230.325.410.495.560.650.740.840.9251.180.190-.220.250-.280.312-.342.375-

8、.405.438-.468.500-.532.562-.597.625-.660.750-.785.045.045.060.070.080.100.110.120.130.250.322.360.458.535.610.680.790.935TABLE 1BPARTNUMBER LTMIN P R AHAPPROXMASSLB/100AS3554-09AS3554-10AS3554-11AS3554-12AS3554-13AS3554-14AS3554-15AS3554-16AS3554-17.190-.210.250-.270.312-.332.375-.395.438-.458.500-.

9、520.562-.582.625-.645.750-.770.082.130.170.210.230.260.320.370.500.004.005.005.005.005.006.006.007.007.006.007.008.009.010.012.014.015.016.0014.0014.0016.0016.0020.0020.0020.0020.0020.25.46.711.262.563.114.636.8112.30NOTES:1. MATERIAL: HEAT RESISTING NICKEL ALLOY AMS5708.2. HARDNESS: 32 TO 44 HRC.3.

10、 FINISH: SILVER PLATE PER AMS2411; SILVER PLATE ONLY ON THREADS WITH OPTIONAL COVERAGE ON COUNTERSINKS. NO SILVER SHALL ENCROACH ON THE SEATING SURFACE. DIMENSIONS APPLY AFTER PLATING.4. PROCUREMENT SPECIFICATION: AS72535. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.6. FLUORESCENT PENETRANT

11、INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN, PRIOR TO PLATING.7. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra.8. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 (ASME PUBLICATION)9. DIMENSIO

12、NS ARE IN INCHES.10. DO NOT USE UNASSIGNED PART NUMBERS.AEROSPACE STANDARD AS3554SHEET 3 OF 3REV.BNUT, SELF-LOCKING, DOUBLE HEXAGON,SILVER PLATED, REDUCED HEIGHT180 KSI, 1400 F, UNS N0700111. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.12. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLIC

13、ATION.13. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.