SAE AS 3588A-2009 Pin and Plug Expansion Set of Parts AL Alloy 2024-T4 and 2024-T351 Short STD and 010 Oversize Diameters UNS A92024《2024-T4和2024-T351铝合金短型成套部件膨胀插针和插头 UNS A92024型标准.pdf

1、AEROSPACE STANDARD (R) PIN AND PLUG, EXPANSION, SET OF PARTS AL ALLOY 2024-T4 AND 2024-T351, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS A92024 AS3588Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in a

2、ny form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: h

3、ttp:/www.sae.org ISSUED 1996-06REAFFIRMED 2006-05 REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN:E-25 REV.AFEDERAL SUPPLY CLASS 5340 AS3588SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technic

4、al andengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may b

5、e reaffirmed, revised, orcancelled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3588ARATIONALE ADD MANUFACTURERS PART NUMBERS, CLARIFY PART MARKING REQUIREMENTS AND GENERAL SA

6、E UPDATING REQUIREMENTS FOR FORMATING. FIGURE 1 - AS3124 PIN FIGURE 2 - AS3123 PLUG TABLE 1 PART NUMBERS AEROSPACE STANDARDPARTNUMBER /3/MANUFACTURERSPART NUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3588-01 PLGA0930010A AS3124-01 AS3123-01 .006 AS3588-02 PLGA1250010A AS3124-02 AS3123-02 .014 AS

7、3588-03 PLGA1560010A AS3124-03 AS3123-03 .022 AS3588-04 PLGA1870010A AS3124-04 AS3123-04 .040 AS3588-05 PLGA2180010A AS3124-05 AS3123-05 .065 AS3588-06 PLGA2500010A AS3124-06 AS3123-06 .102 AS3588-07 PLGA2810010A AS3124-07 AS3123-07 .151 AS3588-08 PLGA3430010A AS3124-08 AS3123-08 .258 AS3588-09 PLGA

8、4060010A AS3124-09 AS3123-09 .423 AS3588-10 PLGA4680010A AS3124-10 AS3123-10 .624 AS3588-11 PLGA5310010A AS3124-11 AS3123-11 1.062 AS3588-12 PLGA6560010A AS3124-12 AS3123-12 1.692 AS3588-51 PLGA1030010A AS3124-01 AS3123-51(a) .008 AS3588-52 PLGA1350010A AS3124-02 AS3123-52(a) .016 AS3588-53 PLGA1660

9、010A AS3124-03 AS3123-53(a) .025 AS3588-54 PLGA1970010A AS3124-04 AS3123-54(a) .045 AS3588-55 PLGA2280010A AS3124-05 AS3123-55(a) .072 AS3588-56 PLGA2600010A AS3124-06 AS3123-56(a) .111 (a) DESIGNATES .010 OVERSIZED PLUG. Copyright SAE International Provided by IHS under license with SAENot for Resa

10、leNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3588SHEET 2 OF 2REV. A(R) PIN AND PLUG, EXPANSION, SET OF PARTS AL ALLOY 2024-T4 AND 2024-T351, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS A92024 TABLE 1 PART NUMBERS (CONTINUED) AEROSPACE STANDARDPARTNUMBER

11、 /3/MANUFACTURERSPART NUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3588-57 PLGA2910010A AS3124-07 AS3123-57(a) .161 AS3588-58 PLGA3530010A AS3124-08 AS3123-58(a) .277 AS3588-59 PLGA4160010A AS3124-09 AS3123-59(a) .448 AS3588-60 PLGA4780010A AS3124-10 AS3123-60(a) .650 AS3588-61 PLGA5410010A AS31

12、24-11 AS3123-61(a) 1.105 AS3588-62 PLGA6660010A AS3124-12 AS3123-62(a) 1.753 (a) DESIGNATES .010 OVERSIZED PLUG. NOTES: 1. MATERIAL: DASH NUMBERS 01 THROUGH 08 AND 51 THROUGH 58 - AL ALLOY 2024 - T4 PER AMS4120. DASH NUMBERS 09 THROUGH 12 AND 59 THROUGH 62 - AL ALLOY 2024 - T3521 PER AMS4120 REF. 2.

13、 FINISH: a. PLUG: ANODIZE PER MIL-A-8625, SEE AS3123 REF. b. PIN: CHEMICAL CONVERSION COATING MIL-DTL-5541, SEE AS3124 REF. /3/ MARK PART NUMBER AND MANUFACTURERS IDENTIFICATION ON PACKAGE. MARK AS3588-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. 4. S

14、EE AIR3276 FOR HOLE PREPARATION AND AIR3277 FOR INSTALLATION PROCEDURE. 5. PIN AND PLUG EXPANSION SET OF PARTS SHALL CONTAIN A PIN SIZE FROM AS3124 AND A PLUG SIZE FROM AS3123 AS SPECIFIED WITH CORRESPONDING DASH NUMBER IN TABLE 1. 6. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. MIL IS AN US

15、GOVERNMENT PUBLICATION. 7. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE

16、REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THI

17、S DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE

18、 APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-