SAE AS 39029 9B-2010 CONTACTS ELECTRICAL CONNECTOR PIN CRIMP REMOVABLE THERMOCOUPLE (FOR MIL-DTL-26482 SERIES 2 AS81703 SERIES 3 MIL-DTL-83723 SERIES I AND III AND MIL-DTL-83733 CO.pdf

1、AEROSPACE STANDARD CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, THERMOCOUPLE, (FOR MIL-DTL-26482 SERIES 2, AS81703 SERIES 3, MIL-DTL-83723 SERIES I AND III, AND MIL-DTL-83733 CONNECTORS)AS39029/9Copyright 2010 SAE International All rights reserved. No part of this publication may be reprodu

2、ced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-

3、776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-03REVISED 2010-09THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C REV.BFEDERAL SUPPLY CLASS 5999 AS39029/9SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION: AS39029SAE Technical Standards Board Rules provide that: “This repo

4、rt ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport

5、 at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS39029/9BRATIONALE REVISION IS REQUIRED TO CORREC

6、T DIMENSION “MM” RIGHT SIDE LEADER LINE POSITION IN FIGURE 1, IT IS CURRENTLY DEPICTED ON THE WRONG SIDE OF THE CONTACT SHOULDER. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF: SAE AS39029. FIGURE 1- AS39029/9 PIN

7、 CONTACT (SIZE 16 AND 20) TABLE 1 - CONTACT DIMENSIONS BINCODE ADIABDIACDIADDIAEDIAGDIAHDIALMAX(REF) N P S X MM 132THROUGH 1360.078 0.050 0.103 0.078 0.041 0.066 0.0320.7200.186 0.171 0.549 0.033 0.1300.076 0.048 0.100 0.076 0.039 0.062 0.026 0.157 0.160 0.543 0.029 0.125514THROUGH 5180.103 0.068 0.

8、133 0.103 0.0635 0.089 0.0420.8210.284 0.257 0.564 0.048 0.1300.101 0.066 0.130 0.101 0.0615 0.083 0.036 0.250 0.246 0.558 0.044 0.125Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDAR

9、D AS39029/9SHEET 2 OF 3REV. BCONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, THERMOCOUPLE, (FOR MIL-DTL-26482 SERIES 2, AS81703 SERIES 3, MIL-DTL-83723 SERIES I AND III, AND MIL-DTL-83733 CONNECTORS)TABLE 2 - MARKING AND DESIGN CHARACTERISTICS BINCODES COLOR BANDS MATING ENDSIZEWIREBARREL SIZE

10、 TYPE CLASS 1ST 2ND 3RD 132 BROWN ORANGE RED 20 20 C-COPPER WITH GOLD FLASH B 133 BROWN ORANGE ORANGE 20 20 C-COPPER-NICKEL ALLOY B 134 BROWN ORANGE YELLOW 20 20 C-NICKEL-ALUMINUM/SILICON B 135 BROWN ORANGE GREEN 20 20 C-NICKEL-CHROMIUM B 136 BROWN ORANGE BLUE 20 20 C-IRON WITH CADMIUM PLATING B 514

11、 GREEN BROWN YELLOW 16 16 C-COPPER WITH GOLD FLASH B 515 GREEN BROWN GREEN 16 16 C-COPPER-NICKEL ALLOY B 516 GREEN BROWN BLUE 16 16 C-NICKEL-ALUMINUM/SILICON B 517 GREEN BROWN VIOLET 16 16 C-NICKEL-CHROMIUM B 518 GREEN BROWN GRAY 16 16 C-IRON WITH CADMIUM PLATING B TABLE 3 -TOOL REQUIREMENTS BINCODE

12、 BASICCRIMPING TOOL POSITIONER INSTALLINGTOOL REMOVAL TOOL WIREDCONTACT UNWIRED CONTACT 132, 133, 134, 135, & 136 M22520/1-01OR M22520/2-01 M22520/1-02 RED OR M22520/2-02M81969/14-11 M81969/14-11 M81969/30-05 RED514, 515, 516, 517, & 518 M22520/1-01 OR M22520/7-01 M22520/1-02 BLUE OR M22520/7-03 M81

13、969/14-03 M81969/14-03 M81969/30-06 BLUETABLE 4 - PART NUMBERS AS39029 PART NUMBER BINCODE SUPERSEDESPART NUMBER(S) M39029/9-132 132 M39029/9-20-20 C1 M39029/9-133 133 M39029/9-20-20 C2 M39029/9-134 134 M39029/9-20-20 C3 M39029/9-135 135 M39029/9-20-20 C4 M39029/9-136 136 M39029/9-20-20 C5 M39029/9-

14、514 514 5000-070-516 1/M39029/9-515 515 5000-070-416 1/M39029/9-516 516 5000-070-116 1/M39029/9-517 517 5500-070-216 1/M39029/9-518 518 5000-070-316 1/REQUIREMENTS: ALL REQUIREMENTS SHALL BE HEREIN AND AS39029. 1. DESIGN: CONTACT SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1, TABLES 1 AND 2. DIMENSI

15、ONS ARE IN INCHES AND SHOWN AFTER PLATING. ALL DIMENSIONS PROVIDED IN PARENTHESES ARE METRIC EQUIVALENTS AND ARE GIVEN FOR GENERAL INFORMATION ONLY (SEE AS39029 SECTION 6). SPHERICAL END DIMENSIONS SHALL CONFORM TO AS39029. 2. TOOLS: TOOLS REQUIRED FOR CRIMPING CONTACTS TO WIRE/CABLE AND THE INSTALL

16、ING/REMOVAL FROM THE CONNECTOR SHALL BE IN ACCORDANCE WITH TABLE 3. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/9SHEET 3 OF 3REV. BCONTACTS, ELECTRICAL CONNECTOR, PIN,

17、CRIMP REMOVABLE, THERMOCOUPLE, (FOR MIL-DTL-26482 SERIES 2, AS81703 SERIES 3, MIL-DTL-83723 SERIES I AND III, AND MIL-DTL-83733 CONNECTORS)3. PART NUMBERS: CONTACT PART NUMBERS SHALL BE IN ACCORDANCE WITH TABLE 4. SUPERSEDING PART NUMBERS ARE AS SPECIFIED. 4. MATERIALS: MATERIALS SHALL BE IN ACCORDA

18、NCE WITH AS39029. 5. MECHANICAL: MECHANICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. TENSILE STRENGTH SHALL BE AS SHOWN IN TABLE 5. TABLE - 5 CONTACT TENSILE STRENGTH BIN CODE TENSILE STRENGTH (LB) WIRE SIZE AXIAL LOAD 132, 133, 134, 135, & 136 24 6 20 12 514, 515, 516, 517, & 518 20 14 16 45

19、 6. ELECTRICAL: NOT REQUIRED. 7. ENVIRONMENTAL: ENVIRONMENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. 8. APPLICATION NOTES: CONTACT MATES DIRECTLY INTO AN AS39029/10 SOCKET AS SHOWN TABLE 6. TABLE - 6 CONTACT MATING PART NUMBERS AS39029/9 BIN CODE MATING AS39029/10 BIN CODE 132 138 133 139 1

20、34 140 135 141 136 142 514 519 515 520 516 521 517 522 518 523 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE

21、USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-