SAE AS 4099D-2012 ADAPTER ASSEMBLY - PORT CONNECTION RING LOCKED TO FLARELESS TUBE END《非扩口式管端用适配器、组件、油口接头、环锁》.pdf

1、AEROSPACE STANDARD ADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO FLARELESS TUBE END AS4099Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoc

2、opying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1988-02REAFFIRMED 2000-06 RE

3、VISED 2012-03THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.DFEDERAL SUPPLY CLASS 4730 AS4099SHEET 1 OF 3REV. DPROCUREMENT SPECIFICATION: /4/ AS18280SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis

4、report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, stabilized or cancell

5、ed.SAEinvites yourwrittencommentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4099DRATIONALE ADD AMS5853 OPTION FOR A286 LOCKRING MATERIAL. FIGURE 1 - ADAPTER, ASSEMBLY TABLE 1A - DIMENSIONS A-G BASIC NO. AS4

6、099/17/SIZE CODE (NOMINAL TUBE SIZE)ATHREADAS8879BTHREADAS8879 C D/7/E+.005-.002 FMIN G 020304050608101216202432.125 .188 .250 .312 .375 .500 .625 .750 1.000 1.250 1.500 2.000 .3125-24UNJF-3A .3750-24UNJF-3A .4375-20UNJF-3A .5000-20UNJF-3A .5625-18UNJF-3A .7500-16UNJF-3A .8750-14UNJF-3A 1.0625-12UNJ

7、-3A 1.3125-12UNJ-3A 1.6250-12UNJ-3A 1.8750-12UNJ-3A 2.5000-12UNJ-3A .2160-28UNJF-3A .2500-28UNJF-3A .3125-24UNJF-3A .3750-24UNJF-3A .4375-20UNJF-3A .5625-18UNJF-3A .6875-24UNJEF-3A .8125-20UNJEF-3A 1.1250-18UNJEF-3A 1.3125-18UNJEF-3A 1.6250-18UNJEF-3A 2.1250-16UNJ-3A .400 .468 .514 .624 .700 .814 1.

8、040 1.170 1.456 1.782 2.031 2.548 .090- .096 .122- .128 .169- .175 .231- .237 .294- .300 .419- .425 .497- .503 .653- .659 .872- .878 1.090-1.096 1.341-1.347 1.810-1.816 .154 .186 .239 .301 .364 .482 .625 .737 1.000 1.225 1.502 2.040 .246 .278 .331 .393 .456 .574 .717 .891 1.154 1.379 1.656 2.194 .31

9、7 .349 .400 .491 .544 .670 .824 .981 1.251 1.466 1.768 2.311 AEROSPACE STANDARD AS4099SHEET 2 OF 3REV. DADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO FLARELESS TUBE END TABLE 1B - DIMENSIONS H-M AND WEIGHTS BASIC NO. AS4099/17/SIZE CODE H+.010-.005 J+.000-.015 K+.010-.005 L.007 MLB/EAMAX0203040

10、50608101216202432.674 .721 .752 .752 .789 .882 .945 1.018 1.018 1.045 1.045 1.086 .300.355.355.381.395.430.465.527.564.569.608.730.125.125.125.125.125.125.125.157.157.157.157.157.192.192.192.192.210.210.210.220.220.240.240.24024 26 30 36 36 40 38 40 36 56 81 102.012.017.022.027.033.052.083.111.165.2

11、36.285.535NOTES: 1. MATERIAL: a. FITTING: 6AL-4V TITANIUM ALLOY PER AMS4928, AMS4965, OR AMS4967. b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, AMS5737 OR AMS5853. 2. HEAT TREATMENT: a. FITTING: 130 ksi UTS MIN b. LOCKRING: 34 TO 40 HRC 3. FINISH: a. FITTING: ANODIC TREA

12、TMENT PER AMS2488, TYPE 2. b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2 or 8. /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON THIS STANDARD. COMPONENTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) Q

13、UALIFIED PRODUCTS LIST FOR PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/www.pri.sae.org/QPL/as18280.pdf FOR CURRENT QPL ONLINE. /5/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT. /6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. /7/ “D” DIAMETER FOR DASH -04 IS .18

14、4-.190 ON AS33514 OR AS4375 ENDS AND REDUCED TO “D” DIAMETER PER THIS STANDARD ON OPPOSITE END. /8/ IDENTIFICATION: a. MARK AT LOCATION(S) SHOWN PER AS478 METHOD 2 OR 15, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE. b. MARK PER AS478, METHOD 35D, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE AND PART

15、NUMBER. AEROSPACE STANDARD AS4099SHEET 3 OF 3REV. DADAPTER, ASSEMBLY - PORT CONNECTION RING LOCKED TO FLARELESS TUBE END 9. WORKING PRESSURE: THIS PART IS DESIGNED FOR USE IN 4000 psi WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM. 10. ADAPTERS TO BE INSTALLED PER AS1301 INTO BOSS CAVITIES PER AS

16、1300. 11. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCU

17、MENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 12. INTERPRETATION OF DRAWING PER ARP4296. 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACH

18、INED SURFACES TO BE 125 in Ra AND SEALING SURFACE TO BE 63 in Ra. 14. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 15. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 16. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 0 DEGREES 30. /17/ EXAMPLE OF PART NUMBER: 18. INVENTORIED PARTS CONFORMING TO REVISION B, DATED 2005-05 ARE ACCEPTABLE UNTIL SUPPLIES TO DEPLETION. 19. TITANIUM NOT RECOMMENDED FOR USE IN OXYGEN SYSTEMS.