SAE AS 4500D-2015 HOSE ASSEMBLY CONVOLUTED POLYTETRAFLUOROETHYLENE METALLIC REINFORCED CONDUCTIVE FLARED STRAIGHT TO 45 .pdf

1、 AEROSPACE STANDARD HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCEDCONDUCTIVE, FLARED, STRAIGHT TO 45 AS4500Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any

2、means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.or

3、g ISSUED 1991-12REVISED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3D REV.D FEDERAL SUPPLY CLASS AS4500 SHEET 1 OF 5 REV. D PROCUREMENT SPECIFICATION: AS620 /2/SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences

4、. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilize

5、d, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4500D RATIONALE CORRECTED NOTE NUMBERS AND CLARIFIED COVER CODES SHOWN IN TABLE 3. UPDATED NOTE 2 TO CURRENT STANDA

6、RD QPL WORDING. FIGURE 1 - HOSE ASSEMBLY FIGURE 2 - SPIRAL AND POLYESTER ABRASION COVER /6/, /7/ AEROSPACE STANDARD AS4500 SHEET 2 OF 5 REV. D HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARED, STRAIGHT TO 45 TABLE 1 - ASSEMBLY DIMENSIONS HOSE ASSEMBLY AS4500

7、 SIZE CODE HOSE ASSEMBLY SIZE REF THREAD T PER AS8879 REF A1MAX A2MAX C /8/MIN D MIN D MAX E /9/ MAX WITHOUT SLEEVING F HEX REF 04 .250 .4375-20UNJF-3B 1.20 1.62 .132 .312 .382 .55 .56 06 .375 .5625-18UNJF-3B 1.28 1.86 .256 .436 .506 .68 .69 08 .500 .7500-16UNJF-3B 1.44 2.18 .345 .537 .607 .86 .88 1

8、0 .625 .8750-14UNJF-3B 1.58 2.42 .430 .608 .678 .95 1.00 12 .750 1.0625-12UNJ-3B 1.74 2.77 .635 .644 .714 1.28 1.25 16 1.000 1.3125-12UNJ-3B 1.79 3.05 .835 .755 .825 1.47 1.50 20 1.250 1.6250-12UNJ-3B 2.29 3.68 1.085 .894 .964 1.70 1.81 24 1.500 1.8750-12UNJ-3B 2.38 3.95 1.310 1.016 1.086 2.00 2.12

9、32 2.000 2.5000-12UNJ-3B 3.00 5.38 1.780 1.300 1.370 2.56 2.75 TABLE 2 - ASSEMBLY LENGTH TOLERANCE +.250/-.125 INCH FOR LENGTHS UNDER 18 INCHES +.500/-.250 INCH FOR LENGTHS FROM 18 TO 36 INCHES EXL. +1.000/-.500 INCH FOR LENGTHS FROM 36 TO 50 INCHES EXL. +2%/-1% FOR LENGTHS 50 INCHES AND OVER TABLE

10、3 - HOSE OR COVER OUTSIDE DIAMETER HOSE SIZE COVER CODE HOSE OR TYPE OF PROTECTIVE COVER .250 .375 .500 .625 .750 1.00 1.25 1.50 2.00 UPPERTEMP.LIMIT F HOSE ONLY PER AS620 .413/.477 .523/.587 .723/.787 .818/.882 1.028/1.092 1.266/1.330 1.494/1.558 1.758/1.822 2.293/2.357 B SPIRAL ABRASION /6/ .505 .

11、615 .825 .935 1.140 1.358 1.630 1.890 2.395 275 H INTEGRAL FIRESLEEVE /10/ .710/.760 .798/.862 .978/1.055 1.100/1.202 1.300/1.392 1.478/1.610 1.718/1.840 1.968/2.120 2.480/2.564 400 N FIRESLEEVE SIL/FG (AS1072) /10/ /11/ /12/ .900 1.030 1.150 1.380 1.590 1.800 2.060 2.320 2.740 400 K INTEGRAL ABRASI

12、ON /7/ (BRAIDED) POLYESTER .468/.532 .598/.662 .808/.872 .888/.952 1.103/1.167 1.313/1.405 1.568/1.632 1.838/1.902 2.370/2.452 300 J INTEGRAL FIRESLEEVE /13/ .653/.717 .763/.827 .963/1.027 1.058/1.122 1.268/1.332 1.498/1.562 2.480/2.564 400 TABLE 4 - HOSE ASSEMBLIES PHYSICAL CHARACTERISTICS HOSE SIZ

13、E REF OPERATING PRESSURE MAX PSI PROOF PRESSURE MIN PSI BURST PRESSURES ROOM TEMP MIN PSI BURST PRESSURES HIGH TEMP MIN PSI BEND RADIUS AT INSIDE OF BEND INCHES (HOSE ONLY) 04 1000 2000 4000 2800 1.25 06 1000 2000 4000 2800 2.25 08 1000 2000 4000 2800 2.88 10 1000 1800 3600 2500 3.00 12 1000 1800 36

14、00 2500 3.75 16 1000 1800 3600 2500 5.00 20 1000 1800 3600 2500 6.25 24 750 1500 3000 2100 7.50 32 250 500 1000 700 10.00 AEROSPACE STANDARD AS4500 SHEET 3 OF 5 REV. D HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARED, STRAIGHT TO 45 TABLE 5 - WEIGHTS (NOM) H

15、OSE SIZE REF HOSE ONLY LB/IN HOSE WITH SPIRAL ABRASION COVER CODE B LB/IN HOSE WITH INTEGRAL FIRESLEEVECOVER CODE H & J LB/IN HOSE WITH TUBULAR FIRESLEEVECOVER CODE N LB/IN HOSE WITH POLYESTERABRASION COVER CODE K LB/IN STR END FITTING LB EACH 45 END FITTING LB EACH 04 .010 .011 .018 .009 .06 .06 06

16、 .010 .014 .028 .021 .012 .10 .10 08 .022 .020 .032 .030 .018 .16 .18 10 .020 .025 .042 .035 .022 .25 .28 12 .027 .032 .050 .044 .028 .34 .40 16 .040 .039 .055 .057 .038 .49 .60 20 .055 .060 .070 .077 .045 .90 .96 24 .060 .071 .082 .107 .058 1.28 1.33 32 .090 .105 .129 .142 .100 2.01 2.40 TABLE 6 -

17、SLEEVE LENGTH REF HOSE SIZE LENGTH (IN) 04/06 2.00 .25 08/10 2.50 .25 12/16 3.00 .25 20/24 3.50 .25 32 4.00 .25 TABLE 7 - MINIMUM INSPECTION BALL SIZE FOR VERIFYING HOSE ASSEMBLY ID /8/ HOSE SIZE REF STRAIGHT END FITTING DIA IN ELBOW END FITTING DIA IN 04 .119 .112 06 .230 .218 08 .310 .293 10 .387

18、.366 12 .572 .540 16 .752 .710 20 .976 .922 24 1.179 1.11432 1.602 1.513AEROSPACE STANDARD AS4500 SHEET 4 OF 5 REV. D HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARED, STRAIGHT TO 45 NOTES: 1. MATERIALS: HOSE AND FITTINGS PER AS620, TYPE II, CLASS 1 OR 2, AS

19、 SPECIFIED BY PART NUMBER. CODE B, SPIRAL ABRASION COVER, BLACK NYLON COIL PER AS1294 CODE H AND J, INTEGRAL FIRESLEEVE, RED OR BROWN SILICONE CODE N, TUBULAR FIRESLEEVE, FIBERGLASS SILICONE PER AS1072 CODE K, INTEGRAL ABRASION SLEEVE, BRAIDED POLYESTER /2/ PROCUREMENT SPECIFICATION: AS620 EXCEPT AS

20、 SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED AND ASSEMBLED BY AN ACCREDITED MANUFACTURER OR ASSEMBLED BY AN ACCREDITED DISTRIBUTOR LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI QPL AS620 FOR THIS STANDARD. SEE www.eAud

21、itN FOR CURRENT QPL ON-LINE. 3. MARKING SHALL BE PER AS620 ON A STAINLESS STEEL BAND NOT OVER 1.0 INCH WIDE OR ON THE END FITTING COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 INCH HIGH. THE BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON THE HOSE TO PREVENT RELATIVE MOTION AND CHAFING. IT SHALL

22、BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. 4. CONSTRUCTION AND PERFORMANCE PER AS620. FITTINGS SHALL BE PERMANENTLY ATTACHED TO HOSE. /5/ LENGTH “L” IS A FOUR DIGIT NUMBER OF WHICH THE FIRST THREE DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE FOURTH DIGIT IN FRACTION O

23、F AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM “END” TO “END.” SEE TABLE 2 FOR LENGTH TOLERANCES. /6/ SPIRAL ABRASION COVER WHEN ASSEMBLED IN THE STRAIGHT CONDITION ON THE HOSE SHALL HAVE AN AVERAGE GAP BETWEEN SPIRALS NOT EXCEEDING .05 INCH. DISPLACEMENT OF THE SPIRAL COVER, CAUSING A GREATER GA

24、P, SHALL NOT BE CAUSE FOR REJECTION IF THE SPIRALS CAN BE REPOSITIONED TO MEET THE GAP REQUIREMENT. ENDS OF THE SPIRAL COVER SHALL BE TERMINATED WITH A LENGTH OF AMS-DTL-23053/5 BLACK POLYOLEFIN TUBING PER TABLE 6 AND FIGURE 2. /7/ BRAIDED POLYESTER ABRASION COVER SHALL FORM AN INTEGRAL, PERMANENT P

25、ART OF THE HOSE AND SHALL TERMINATE A MAXIMUM OF .625 INCH FROM THE END OF THE END FITTING COLLAR. ENDS OF POLYESTER ABRASION COVER MAY BE TERMINATED WITH A LENGTH OF AMS-DTL-23053/11 (FEP) CLASS 1 OR 2, COLOR CLEAR, PER TABLE 6 AND FIGURE 2. /8/ HOSE ASSEMBLY INSIDE DIAMETER SHALL BE VERIFIED BY PA

26、SSING THE DESIGNATED, OR LARGER, SPHERICAL BALL PER TABLE 7 THROUGH THE HOSE ASSEMBLY. /9/ DISTANCE ACROSS CORNERS OF COUPLING NUT, NIPPLE HEX OR SOCKET HEX MAY EXCEED THIS DIMENSION. /10/ ADD “AS1055 TYPE IIb CLASS B-S/P” OR “AS150 TYPE IIIbB” TO IDENTIFICATION MARKING TO SHOW LEVEL OF COMPLIANCE,

27、“FIRE-PROOF” (15 MIN), WITH AS1055 OR AS150. /11/ THE CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER, OR EQUIVALENT, PRIOR TO INSTALLATION TO PREVENT WICKING OF FLUID. THE FIRESLEEVE ENDS SHALL BE SECURED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AF

28、TER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE, WHICH EXPOSE THE FIBERGLASS, SHALL BE COATED WITH RTV SILICONE. /12/ THE TABLE 3 SLEEVE DIAMETERS ARE THE AS1072 MAXIMUM FOR THE LARGEST SIZE FIRESLEEVE AS QUALIFIED BY THE VARIOUS HOSE ASSEMBLY MANUFACTURERS. THE SLEEVE MAY STRETCH OVER A FITTING

29、, OR WRINKLE OVER THE HOSE DUE TO SLEEVE LENGTH TO ALLOW HOSE BENDING. THE SLEEVE MAY BE COMPRESSED OVER THE HOSE FOR MEASUREMENT OR CLAMPING. IN THIS CASE A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE. /13/ ADD “AS1055 TYPE IIa CLASS A-S/P” OR “AS150 TYPE IIIaA” TO IDENTIFI

30、CATION MARKING TO SHOW LEVEL OF COMPLIANCE, “FIRE RESISTANT” (5 MIN), WITH AS1055 OR AS150. 14. STANDARD COUPLING NUTS SHALL BE IN ACCORDANCE WITH AN818 OR AS4370 AND MATE WITH AS4395 FLARED FITTING END. NONSTANDARD COUPLING NUTS MAY BE USED PROVIDED THEY ARE DIMENSIONALLY AND FUNCTIONALLY EQUIVALEN

31、T AND PROVIDED THEY CANNOT BE REMOVED FROM THE FITTING AND USE THE SAME MATERIALS. AEROSPACE STANDARD AS4500 SHEET 5 OF 5 REV. D HOSE ASSEMBLY, CONVOLUTED, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED CONDUCTIVE, FLARED, STRAIGHT TO 45 15. DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED. 16. EXA

32、MPLE OF PART NUMBER: 17. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS4500 FRACTIONAL LENGTH IN EIGHTHS OF AN INCH, .250 INCH /5/ LENGTH IN WHOLE INCHES, 24 INCHES /5/