SAE AS 4692E-2009 FITTING ASSEMBLY TEE FLARELESS AND SHORT FLARELESS REDUCER RETAINED NUT ON SIDE《侧面固定螺母减压器非扩口和短非扩口三通配件》.pdf

1、 AEROSPACE STANDARD FITTING ASSEMBLY, TEE, FLARELESS AND SHORTFLARELESS, REDUCER, RETAINED NUT ON SIDE AS4692Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mech

2、anical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1992-07REAFFIRMED

3、 2007-11 REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.E FEDERAL SUPPLY CLASS 4730 AS4692 SHEET 1 OF 6 REV. E PROCUREMENT SPECIFICATION: /4/ AS18280SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering science

4、s. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, or

5、cancelled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4692E RATIONALE PROCUREMENT SPECIFICATION CHANGED FROM AS4444 TO AS18280 AND PROCUREMENT NOTE UPDATED. WARNING NOTICE FO

6、R CADMIUM PLATING HAS BEEN INSERTED. UPDATES: MIL-S-8879 CLASS B TO AS8879 CLASS 3B. MATERIAL AND FINISH SPECIFICATIONS UPDATED. FIGURE 1 - TEE ASSEMBLY FIGURE 2 - INSTALLATION, RETAINED NUT AND RETAINING WIRE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reprodu

7、ction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4692SHEET 2 OF 6REV. EFITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON SIDE TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4692/10/ /19/ SIZE CODE D H J+.005/-.020 LB/EAAPPROX REF ALUMLB/EAAPP

8、ROX REF CRESLB/EAAPPROX REF TI20 .517 .124 1.375 .395 1.146 .666 24 .614 .156 1.688 .570 1.651 .954 TABLE 2 - WIRE INSERTION DEPTH PORT SIZE(NOMINAL TUBE SIZE) C 04 .250 .076 05 .312 .076 06 .375 .084 08 .500 .095 10 .625 .114 12 .750 .150 16 1.000 .176 20 1.250 .247 24 1.500 .287 TABLE 3 - LEG LENG

9、TH A SIZE OF PORT #1 FOR ALL PORTS THE SAME SIZE USE AS4674. /11/ PORT #1 IS LARGER OR EQUAL TO PORT #2. 12. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS

10、 DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 13. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “

11、LETTER CHANGE” MAY BE USED TO DEPLETION /4/. 14. INTERPRETATION OF DRAWING PER ARP4296. 15. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36 M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. 16. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 17. DIMENSIONIN

12、G AND TOLERANCING: ASME Y14.5M-1994 18. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5 DEGREES. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS4692SHEET 6 OF 6REV. EFITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON SIDE /19/Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-