SAE AS 5008B-2015 FITTING UNION EXTERNAL SWAGE HYDRAULIC.pdf

1、 AEROSPACE STANDARD FITTING, UNION, EXTERNAL SWAGE, HYDRAULIC AS5008Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or other

2、wise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1997-11 REAFFIRMED2007-11 REVISED2015-12 THIRD ANGLE PRO

3、JECTION CUSTODIAN: G-3/G-3B REV.B FEDERAL SUPPLY CLASS 4730 AS5008 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS4459 /5/ SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits

4、 applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled. SAEinvites yourwritten comments andsuggestion

5、s.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS5008B RATIONALE REMOVED QPL EFFECTIVITY DATE FROM NOTE 5 SINCE THE QPL WAS PUBLISHED. REVISED NOTE 2 TO CLARIFY DIMENSIONS B AND C. NON-REDUCER VIEW REDUCER VIEW FIGURE 1 - FIT

6、TING, UNION, EXTERNAL SWAGE AEROSPACE STANDARD AS5008 SHEET 2 OF 3 REV. B FITTING, UNION, EXTERNAL SWAGE, HYDRAULIC TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS5008 /14/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 A B1 +.000 -.003 /2/ B2 +.000 -.003 /2/ C1 /2/ C2 /2/ V1 /2/ V2 /2/ WEI

7、GHT APPROX LB/EA CRES WEIGHT APPROX LB/EA TI WEIGHT APPROX LB/EA AL 0303 .188 .188 1.245-1.255 .275 .275 .195- .198 .195- .198 .170-.220 .170-.220 .010 .006 .004 0403 .250 .188 1.640-1.670 .338 .275 .257- .260 .195- .198 .190-.240 .170-.220 .015 .008 .005 0404 .250 .250 1.530-1.540 .338 .338 .257- .

8、260 .257- .260 .190-.240 .190-.240 .016 .009 .006 0503 .312 .188 1.688-1.718 .413 .275 .319- .322 .195- .198 .200-.250 .170-.220 .018 .010 .006 0504 .312 .250 1.765-1.795 .413 .338 .319- .322 .257- .260 .200-.250 .190-.240 .021 .012 .007 0505 .312 .312 1.610-1.620 .413 .413 .319- .322 .319- .322 .20

9、0-.250 .200-.250 .024 .014 .008 0603 .375 .188 1.790-1.820 .480 .275 .382- .385 .195- .198 .220-.270 .170-.220 .023 ,013 .008 0604 .375 .250 1.850-1.880 .480 .338 .382- .385 .257- .260 .220-.270 .190-.240 .025 .014 .009 0605 .375 .312 1.875-1.905 .480 .413 .382- .385 .319- .322 .220-.270 .200-.250 .

10、028 .016 .010 0606 .375 .375 1.680-1.690 .480 .480 .382- .385 .382- .385 .220-.270 .220-.270 .031 .018 .010 0803 .500 .188 2.375-2.405 .655 .275 .508- .511 .195- .198 .410-.435 .170-.220 .054 .029 .015 0804 .500 .250 2.415-2.445 .655 .338 .508- .511 .257- .260 .410-.435 .190-.240 .055 .030 .017 0805

11、 .500 .312 2.425-2.455 .655 .413 .508- .511 .319- .322 .410-.435 .200-.250 .058 .032 .019 0806 .500 .375 2.425-2.455 .655 .480 .508- .511 .382- .385 .410-.435 .220-.270 .061 .035 .021 0808 .500 .500 2.686-2.700 .655 .655 .508- .511 .508- .511 .410-.435 .410-.435 .100 .060 .035 1004 .625 .250 2.550-2

12、.580 .787 .338 .633- .636 .257- .260 .410-.435 .190-.240 .079 .045 .027 1005 .625 .312 2.560-2.590 .787 .413 .633- .636 .319- .322 .410-.435 .200-.250 .084 .048 .029 1006 .625 .375 2.590-2.620 .787 .480 .633- .636 .382- .385 .410-.435 .220-.270 .087 .050 .030 1008 .625 .500 2.953-2.983 .787 .655 .63

13、3- .636 .508- .511 .410-.435 .410-.435 .103 .059 .035 1010 .625 .625 2.766-2.780 .787 .787 .633- .636 .633- .636 .410-.435 .410-.435 .132 .080 .046 1204 .750 .250 2.620-2.650 .929 .338 .758- .761 .257- .260 .365-.390 .190-.240 .104 .060 .036 1206 .750 .375 2.640-2.670 .929 .480 .758- .761 .382- .385

14、 .365-.390 .220-.270 .108 .062 .037 1208 .750 .500 3.030-3.060 .929 .655 .758- .761 .508- .511 .365-.390 .410-.435 .125 .072 .043 1210 .750 .625 3.030-3.060 .929 .787 .758- .761 .633- .636 .365-.390 .410-.435 .134 .077 .046 1212 .750 .750 2.906-2.920 .929 .929 .758- .761 .758- .761 .365-.390 .365-.3

15、90 .183 .110 .063 1604 1.000 .250 3.070-3.100 1.257 .338 1.008-1.011 .257- .260 .325-.350 .190-.240 .161 .092 .055 1606 1.000 .375 3.340-3.370 1.257 .480 1.008-1.011 .382- .385 .325-.350 .220-.270 .241 .138 .083 1608 1.000 .500 3.420-3.450 1.257 .655 1.008-1.011 .508- .511 .325-.350 .410-.435 .247 .

16、142 .085 1610 1.000 .625 3.375-3.405 1.257 .787 1.008-1.011 .633- .636 .325-.350 .410-.435 .251 .144 .087 1612 1.000 .750 3.375-3.405 1.257 .929 1.008-1.011 .758- .761 .325-.350 .365-.390 .254 .146 .088 1616 1.000 1.000 3.195-3.209 1.257 1.257 1.008-1.011 1.008-1.011 .325-.350 .325-.350 .396 .238 .1

17、37 2016 1.250 1.000 3.850-3.880 1.489 1.257 1.258-1.262 1.008-1.011 .325-.350 .325-.350 .380 .218 .135 2020 1.250 1.250 3.400-3.414 1.489 1.489 1.258-1.262 1.258-1.262 .325-.350 .325-.350 .329 .187 .113 2412 1.500 .750 3.955-3.985 1.786 .929 1.513-1.517 .758- .761 .325-.350 .365-.390 .522 .301 .181

18、2416 1.500 1.000 4.040-4.070 1.786 1.257 1.513-1.517 1.008-1.011 .325-.350 .325-.350 .558 .321 .193 2420 1.500 1.250 4.140-4.170 1.786 1.489 1.513-1.517 1.258-1.262 .325-.350 .325-.350 .570 .329 .198 2424 1.500 1.500 3.650-3.664 1.786 1.786 1.513-1.517 1.513-1.517 .325-.350 .325-.350 .455 .259 .155

19、NOTES: /1/ MATERIAL: a. CODE LETTER “-“: 21-6-9 CORROSION RESISTANT STEEL (CRES) BAR PER AMS5656. b. CODE LETTER “E”: COMMERCIALLY PURE TITANIUM BAR PER AMS4921. c. CODE LETTER “D”: 6061-T6 ALUMINUM ALLOY PER AMS4117. /2/ FINISH AND COATING: a. MATERIAL CODE “-“: PASSIVATE THE WHOLE PART PER AMS2700

20、. POLYTETRAFLUOROETHYLENE (PTFE) COAT (GREEN) SHALL BE APPLIED TO FITTING BORE DIAMETER TO “V” DEPTH. OVERSPRAY ON /Y/ PERMISSIBLE. OVERSPRAY IN GROOVE IS NOT PERMITTED. DIMENSIONS “B” AND “C” APPLY BEFORE PTFE COATING. b. MATERIAL CODE “E”: POLYTETRAFLUOROETHYLENE (PTFE) COAT (BLACK) SHALL BE APPLI

21、ED TO EXTERIOR SURFACES AND BORE DIAMETER TO “V” DEPTH. OVERSPRAY IN GROOVE IS NOT PERMITTED. DIMENSIONS “B” AND “C” APPLY BEFORE PTFE COATING. AEROSPACE STANDARD AS5008 SHEET 3 OF 3 REV. B FITTING, UNION, EXTERNAL SWAGE, HYDRAULIC c. MATERIAL CODE “D”: CHEMICAL CONVERSION COAT ENTIRE PART (INCLUDIN

22、G INTERNAL DIAMETERS) PER MIL-DTL-5541, CLASS 1A. POLYTETRAFLUOROETHYLENE (PTFE) COAT (GREEN) SHALL BE APPLIED TO EXTERIOR SURFACES AND BORE DIAMETER TO “V” DEPTH. OVERSPRAY IN GROOVE IS NOT PERMITTED. DIMENSIONS “B” AND “C” APPLY BEFORE PTFE COATING. 3. LIQUID PENETRANT INSPECT PER ASTM E1417 TYPE

23、1 SENSITIVITY LEVEL 2. LINEAR INDICATIONS PROHIBITED, ROUNDED INDICATIONS ACCEPTABLE. /4/ A MINIMUM OF ONE GROOVE FOR STAINLESS AND TITANIUM FITTINGS AND BOTH GROOVES FOR ALUMINUM FITTINGS SHALL BE FILLED WITH ELASTOMERIC DIMETHYL SILOXANE COMPOUND. /5/ PROCUREMENT SPECIFICATION: AS4459 EXCEPT AS SP

24、ECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS4459 FOR THIS STANDARD. SEE www.eAuditN FOR THE CURRENT QPL ON-LINE. 6. DIMENSIONS AND TOLERAN

25、CES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. 7. FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5902. /8/ IDENTIFICATION: PARTS SHALL BE IDENTIFIED IN THE AREA SHOWN P

26、ER AS4459. 9. INTERPRETATION OF DRAWING PER AS4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENT PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 11. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ASME Y14.5

27、M-1994. 13. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 2q. /14/ EXAMPLE OF PART NUMBER: AS5008 - 08 06 A OPTIONAL OXYGEN CLEANING /15/ BASIC PART NUMBER END 2 SIZE CODE IN .062 INCH INCREMENTS(06 = .375 INCH) MATERIAL CODE LETTER /1/ END

28、1 SIZE CODE IN .062 INCH INCREMENTS (08 = .500 INCH) /15/ PARTS FOR OXYGEN SYSTEMS SHALL BE IDENTIFIED IN THE PART NUMBER AS SUFFIX CODE “A” AND SHALL BE FURNISHED CLEANED, PACKAGED, AND LABELED IN ACCORDANCE WITH ARP1176 CATEGORY 1A. 16. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARG

29、IN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.