SAE AS 5368D-2014 FITTING ASSEMBLY ADAPTER C RING LOCKED PORT CONNECTION TO FLARED TUBE END 3000 PSI.pdf

1、 AEROSPACE STANDARD FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO FLARED TUBE END, 3000 PSI AS5368Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mech

2、anical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-07REAFFIR

3、MED 2007-07 REVISED 2014-12THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.DFEDERAL SUPPLY CLASS 4730 AS5368SHEET 1 OF 3 REV. DPROCUREMENT SPECIFICATION: /4/ AS4841SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences.

4、Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized,

5、 orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5368DRATIONALE TO CORRECT MAX WEIGHT AND GENERAL UPDATE OF STANDARD REFERENCES. FIGURE 1 - ADAPTER ASSEMBLY TABLE 1A

6、- DIMENSIONS BASIC NO. AS5368 /16/ SIZE CODE (NOMINAL TUBE SIZE) A THREAD AS8879 B THREAD AS8879 C D E +.005 .002 F MIN G 04 05 06 08 10 12 16 .250 .312 .375 .500 .625 .750 1.000 .4375-20UNJF-3A .5000-20UNJF-3A .5625-18UNJF-3A .7500-16UNJF-3A .8750-14UNJF-3A 1.0625-12UNJ-3A 1.3125-12UNJ-3A .3125-24U

7、NJF-3A .3750-24UNJF-3A .4375-20UNJF-3A .5625-18UNJF-3A .6875-24UNJEF-3A .8125-20UNJEF-3A 1.1250-18UNJEF-3A .514 .624 .700 .814 1.040 1.170 1.456 .168 - .175 .230 - .237 .293 - .301 .387 - .395 .480 - .488 .604 - .614 .839 - .851 .239 .301 .364 .482 .625 .737 1.000 .331 .393 .456 .574 .717 .891 1.154

8、 .400 .491 .544 .670 .824 .981 1.251 AEROSPACE STANDARD AS5368SHEET 2 OF 3 REV. DFITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO FLARED TUBE END, 3000 PSI TABLE 1B - DIMENSIONS AND WEIGHTS BASIC NO. AS5368 /16/ SIZE CODE H +.010 .005 J +.000 .015 K +.010 .005 L .007 M (P) STAND-OFF AFTER IN

9、STL /9/ .020 WEIGHT LB/EA MAX 04 05 06 08 10 12 16 .856 .856 .931 1.091 1.191 1.301 1.341 .355 .381 .395 .430 .465 .527 .564 .125 .125 .125 .125 .125 .157 .157 .192 .192 .210 .210 .210 .220 .220 30 36 36 40 38 40 36 .690 .690 .750 .910 1.010 1.120 1.160 .040 .050 .065 .110 .175 .265 .360 NOTES 1. MA

10、TERIAL: a. FITTING: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, OR AMS5737. b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, AMS5737, OR AMS5853. 2. HEAT TREATMENT: IF THE RAW MATERIAL IS PROCURED IN THE SOLUTION TREATED CONDITION, AGE PER AMS2759/3 TO: a.

11、 FITTING: 130 KSI UTS MINIMUM. b. LOCKRING: 34 TO 40 HRC. /3/ FINISH a. FITTING: PASSIVATE PER AMS2700, TYPE 2 OR 8 FOLLOWED BY SOLID FILM LUBE PER AS5272, TYPE I ON NOTED SURFACES EXCEPT NONE IN FLOW HOLE, OVERSPRAY PERMISSIBLE ON ADJACENT GROOVE. b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2 OR 8. /4

12、/ PROCUREMENT SPECIFICATION: AS4841 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE NADCAP QUALIFIED MANUFACTURER LIST (QML) FOR THIS TYPE OF PRODUCT.THE QML IS AVAILABLE AT www.eAuditN. /5/ SEALING SURFAC

13、E: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT. /6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. /7/ IDENTIFICATION: a. MARK AT LOCATION SHOWN PER AS478 METHOD 2 OR 15, MANUFACTURERS NAME, TRADEMARK, OR CAGE CODE. b. BAG AND TAG PER AS478, METHOD 35D, MANUFACTURERS NAME, TRADEMA

14、RK, OR CAGE CODE AND PART NUMBER. 8. WORKING PRESSURE: THIS PART IS DESIGNED FOR USE IN 3000 PSI WORKING PRESSURE SYSTEMS COMPATIBLE WITH CRES A286. /9/ ADAPTERS TO BE INSTALLED PER AS1301 INTO BOSS CAVITIES PER AS1300. FOR DESIGN PURPOSES ONLY. INSTALLED STAND-OFF (P) .020 AND INSTALLED LOCKRING HE

15、IGHT, SEE AS1301, “R” MAXIMUM. AEROSPACE STANDARD AS5368SHEET 3 OF 3 REV. DFITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO FLARED TUBE END, 3000 PSI 10. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” OF THIS STANDARD MAY BE USED TO DEPLETION. 11. INTERPRETATION OF DRAWING PER

16、AS4296. 12. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra AND SEALING SURFACE TO BE 63 MICROINCHES Ra. 13. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 14. DIMENSIONING AND TOLERANCING: ASME Y14.

17、5M-1994. 15. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 0 DEGREES 30 MINUTES. /16/ EXAMPLE OF PART NUMBER: AS5368-06 BASIC PART NUMBER SIZE CODE, TUBE SIZE IN .062 INCREMENTS 17. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONV

18、ENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.