SAE AS 5828A-2015 FITTING END BULKHEAD FLARELESS EXTRA FINE THREAD DESIGN STANDARD.pdf

1、 AEROSPACE STANDARD FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD AS5828Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photoc

2、opying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2005-12 REVISED2015-12THIRD A

3、NGLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730 AS5828 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: NONE /1/ SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary,

4、andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled. SAEinvites yourwritten comments andsugg

5、estions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS5828A RATIONALE MAIN GRAPHIC MODIFIED TO CLARIFY LOCATION OF DIM J. FIGURE 1 - FITTING END DESIGN, STYLE G ACHTOL WFFA A2 X 45 5SEALINGSURFACE( C ) Y24 CC47 .002 AATAR .0

6、05 - .020R .005 - .020.005 A G ABB MAXL /2/RSTYLE G JALTERNATE VIEW A ENLARGED TUBE STOP, TYPE F VIEW A ENLARGED TUBE STOP, TYPE NO CODE AEROSPACE STANDARD AS5828 SHEET 2 OF 4 REV. A FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD FIGURE 2 - FITTING END DESIGN, STYLE H SAME AS S

7、TYLE G, EXCEPT AS SHOWN FIGURE 3 - FITTING END DESIGN, STYLE J SAME AS STYLE H, EXCEPT AS SHOWN AEROSPACE STANDARD AS5828 SHEET 3 OF 4 REV. A FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD TABLE 1A - DIMENSIONS A-E BASIC NO. AS5828 /9/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER

8、 ISO 3161 CLASS 3A A .003 B GAGE (C) D +.004/-.000 E 04 .250 .4375-28 UNJEF .187 .2930 .319 .261 .678 - .691 06 .375 .5625-24 UNJEF .297 .4160 .441 .386 .802 - .816 08 .500 .7500-20 UNJEF .422 .5600 .601 .514 .990 - 1.003 10 .625 .8750-20 UNJEF .500 .6860 .727 .641 1.113 - 1.128 12 .750 1.0625-18 UN

9、JEF .656 .8100 .852 .766 1.363 - 1.380 16 1.000 1.3125-16 UNJ .875 1.0620 1.102 1.016 1.613 - 1.630 20 1.250 1.6250-16 UNJ 1.093 1.3160 1.355 1.270 1.863 - 1.880 TABLE 1B - DIMENSIONS G-M BASIC NO. AS5828 /9/ SIZE CODE G +.000/-.005 H .003 J K .005 L M MAX 04 .359 .234 .4294 - .4375 .969 .094 .005 0

10、6 .476 .250 .5538 - .5625 1.015 .094 .010 08 .654 .305 .7406 - .7500 1.156 .125 .010 10 .767 .350 .8647 - .8750 1.297 .125 .010 12 .938 .350 1.0511 - 1.0625 1.406 .125 .010 16 1.188 .415 1.3011 - 1.3125 1.406 .125 .010 20 1.501 .415 1.6136 - 1.6250 1.406 .125 .015 TABLE 1C - DIMENSIONS R-FF BASIC NO

11、. AS5828 /9/ SIZE CODE R .030 V W Y AA .003 BB CC .031 EE FF .005 04 .120 .005 - .020 .005 .365 .060 .090 .562 .668 1.032 06 .140 .005 - .020 .005 .480 .057 .098 .688 .792 1.078 08 .160 .005 - .020 .005 .660 .095 .109 .875 .980 1.250 10 .170 .005 - .020 .005 .775 .095 .122 1.000 1.103 1.391 12 .190

12、.005 - .020 .005 .945 .097 .140 1.187 1.353 1.500 16 .190 .005 - .020 .008 1.195 .093 .140 1.438 1.603 1.500 20 .190 .020 - .030 .008 1.505 .090 .140 1.750 1.853 1.500 AEROSPACE STANDARD AS5828 SHEET 4 OF 4 REV. A FITTING END, BULKHEAD, FLARELESS, EXTRA FINE THREAD, DESIGN STANDARD TABLE 1D - DIMENS

13、IONS GG-MM BASIC NO. AS5828 /9/ SIZE CODE AS568 O-RING /3/ GG .010 JJ MIN KK .001 LL .002 MM .005 HH 04 .855 .865 - .878 .247 .050 .100 .737 -15 06 .980 .990 - 1.003 .267 .050 .100 .861 -17 08 1.166 1.176 - 1.191 .282 .050 .100 1.049 -20 10 1.291 1. 301 - 1.318 .297 .050 .100 1.174 -22 12 1.478 1.48

14、8 - 1.505 .317 .050 .100 1.361 -25 16 1.853 1.863 - 1.880 .337 .050 .100 1.737 -30 20 2.162 2.172 - 2.198 .392 .050 .100 2.014 -32 NOTES: /1/ THIS FITTING END IS DESIGNED FOR USE WITH FITTINGS PER AS4444 OR AS5000. THIS FITTING END CAN BE USED ON UNIONS, ELBOWS, CROSSES AND TEES AT PRESSURES UP TO 5

15、080 PSI. /2/ ON THE STYLE G FITTING END, THE L DIMENSION PROVIDES FOR A WASHER TO FORM A BACKING FACE AGAINST THE BULKHEAD PLUS .031 ADDITIONAL FOR POSITIONING IN THE BULKHEAD. ON THE STYLE H FITTING END, NO WASHER IS REQUIRED. /3/ SIZE ONLY. SELECTION OF O-RING MATERIAL DETERMINED BY FLUID APPLICAT

16、ION. 4. INTERPRETATION OF DRAWING PER AS4296. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.

17、8. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 030. /9/ EXAMPLE OF DRAWING CALLOUT: a. TABULATED PART DRAWING: FITTING END PER AS5828, STYLES G, H, OR J AND TYPE NO CODE OR F. b. INDIVIDUAL PART DRAWING: AS5828 G 08 F 10. REVISION INDICATO

18、R: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. BASIC NUMBER STYLE DESIGNATION (G, H, OR J) SIZE CODE, NOMINAL TUBE SIZE IN .062 INCREMENTS TUBE STOP TYPE (NO CODE OR F)