SAE AS 5962A-2009 HOSE ASSEMBLY POLYTETRAFLUOROETHYLENE CRES BRAID REINFORCED 400 DEGREE F 5080 PSI FLARELESS STRAIGHT TO 45 DEGREES ELBOW《直接连接45弯头的非扩口的400F 5080 psi聚四氟乙烯耐蚀钢编织物增强的软.pdf

1、 AEROSPACE STANDARD HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENECRES BRAID REINFORCED, 400 F, 5080 PSI FLARELESS, STRAIGHT TO 45 ELBOW AS5962Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by a

2、ny means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae

3、.org ISSUED 2004-12REVISED 2009-11THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3D REV.A FEDERAL SUPPLY CLASS 4720 AS5962 SHEET 1 OF 5 REV. A PROCUREMENT SPECIFICATION: AS5960 /2/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineer

4、ing sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, re

5、vised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5962ARATIONALE REVISED PROCUREMENT NOTE /2/, COUPLING NUT NOTE /9/, AND ADDED NOTE /21/ TO CONFORM TO CURRENT R

6、EQUIREMENTS. FIGURE 1 - HOSE ASSEMBLY DIMENSIONS FIGURE 2 - INTEGRAL FIRESLEEVE CUFF /13/ AEROSPACE STANDARD AS5962 SHEET 2 OF 5 REV. A HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE CRES BRAID REINFORCED, 400 F, 5080 PSI FLARELESS, STRAIGHT TO 45 ELBOW TABLE 1 - HOSE ASSEMBLY DIMENSIONS HOSE ASSEMBLY AS596

7、2 SIZE CODE SIZE FITTING TYPE /17/ THREAD T PER AS8879 A1 MAX A2 MAX B GAGE BASIC C HEX (D1) /9/ (D2) /9/ (D3) /9/ (D4) /9/ E .250 - - - - - - - - E .250 S .4375-28UNJ EF-3B 2.64 3.05 .2930 .56 .16 .055 .11 .039 E .250 E .5625-24UNJ EF-3B 2.74 3.09 .4120 .69 .16 .055 .11 .039 G .375 R .4375-28UNJ EF

8、-3B 2.90 3.12 .2930 .56 .16 .055 .11 .039 G .375 S .5625-24UNJ EF-3B 2.94 3.16 .4120 .69 .16 .055 .11 .039 G .375 E .7500-20UNJ EF-3B 3.07 3.46 .5600 .88 .19 .066 .13 .047 H .500 R .5625-24UNJ EF-3B 3.19 3.62 .4120 .69 .16 .055 .11 .039 H .500 S .7500-20UNJ EF-3B 3.32 3.73 .5600 .88 .19 .066 .13 .04

9、7 H .500 E .8750-20UNJ EF-3B 3.39 3.75 .6730 1.00 .20 .066 .14 .047 J .625 R .7500-20UNJ EF-3B 3.55 4.00 .5600 .88 .19 .066 .13 .047 J .625 S .8750-20UNJ EF-3B 3.62 4.06 .6730 1.00 .20 .066 .14 .047 J .625 E 1.0625-18UNJ EF-3B 3.87 4.16 .8100 1.25 .23 .066 .16 .047 K .750 R .8750-20UNJ EF-3B 3.89 4.

10、36 .6730 1.00 .20 .066 .14 .047 K .750 S 1.0625-18UNJ EF-3B 3.95 4.49 .8100 1.25 .23 .066 .16 .047 K .750 E 1.3125-16UNJ-3B 4.06 4.53 1.0620 1.50 .30 .066 .21 .047 M 1.000 R 1.0625-18UNJ EF-3B 4.42 5.35 .8100 1.25 .23 .066 .16 .047 M 1.000 S 1.3125-16UNJ-3B 4.54 5.39 1.0620 1.50 .30 .066 .21 .047 M

11、1.000 E 1.6250-16UNJ-3B 4.64 5.82 1.3160 1.81 .30 .066 .21 .047 N 1.250 - - - - - - - - - N 1.250 S 1.6250-16UNJ-3B 4.72 6.83 1.3160 1.81 .30 - .21 - N 1.250 - - - - - - - - - - TABLE 1 - HOSE ASSEMBLY DIMENSIONS (CONTINUED) HOSE ASSEMBLY AS5962 - SIZE CODE SIZE FITTING TYPE /17/ (D5) /9/ (D6) /9/ E

12、 MIN E MAX F MAX /8/ FITTING BALL SIZE MIN THRU IN /7/ STRAIGHT ELBOW E .250 - - - - - - - - E .250 S .16 .055 .328 .458 .88 .120 .113 E .250 E .16 .055 .368 .498 .88 .120 .113 G .375 R .16 .055 .328 .458 1.00 .120 .113 G .375 S .16 .055 .368 .498 1.00 .203 .192 G .375 E .19 .066 .487 .617 1.00 .203

13、 .192 H .500 R .16 .055 .368 .498 1.20 .203 .192 H .500 S .19 .066 .487 .617 1.20 .297 .281 H .500 E .20 .066 .500 .630 1.20 .297 .281 J .625 R .19 .066 .487 .617 1.41 .297 .281 J .625 S .20 .066 .500 .630 1.41 .369 .349 J .625 E .23 .066 .586 .786 1.41 .369 .349 K .750 R .20 .066 .500 .630 1.69 .36

14、9 .349 K .750 S .23 .066 .586 .786 1.69 .459 .434 K .750 E .30 .066 .631 .831 1.69 .459 .434 M 1.000 R .23 .066 .586 .786 2.00 .459 .434 M 1.000 S .30 .066 .631 .831 2.00 .675 .638 M 1.000 E .30 .066 .750 .950 2.00 .675 .638 N 1.250 - - - - - - - - N 1.250 S .30 - .750 .950 2.25 .833 .786 N 1.250 -

15、- - - - - - - AEROSPACE STANDARD AS5962 SHEET 3 OF 5 REV. A HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE CRES BRAID REINFORCED, 400 F, 5080 PSI FLARELESS, STRAIGHT TO 45 ELBOW TABLE 2 - HOSE AND SLEEVE OUTSIDE DIAMETER /10/ SLEEVE CODE SLEEVE MATERAIL TEMPLIMIT F TOLER-ANCE SIZE.250SIZE.375 SIZE.500 SIZE

16、.625 SIZE .750 SIZE1.000SIZE1.250- (-) INDICATES HOSE ONLY 400 F MAX .510 .620 .760 .960 1.120 1.430 1.685NO SLEEVE (SEE AS5960) REF MIN .450 .560 .700 .835 .995 1.305 1.560C FIRESLEEVE (AS1072 SIL-FG) 400 F MAX .970 1.090 1.220 1.500 1.590 1.950 2.190(15 MIN) /11/ /12/ /14/ MIN .810 1.000 1.060 1.2

17、60 1.470 1.780 1.940F ABRASION SLEEVE SHRINK-ON 275 F MAX .560 .700 .910 1.045 1.205 1.530 1.785(POLYOLEFIN AS1073-CODE B) /16/ MIN .480 .590 .760 .895 1.080 1.370 1.660H FIRESLEEVE, INTEGRAL 400 F MAX .815 .940 1.060 1.200 1.420 1.740 2.000SILICONE (15 MIN) /14/ MIN .755 .880 1.000 1.075 1.295 1.61

18、5 1.875K INTEGRAL ABRASION SLEEVE 300 F MAX .590 .710 .860 1.065 1.205 1.530 1.815(BRAIDED POLYESTER) /15/ MIN .530 .650 .735 .885 1.130 1.405 1.690TABLE 3 - HOSE ASSEMBLY LENGTH TOLERANCE HOSE ASSEMBLY LENGTH TOLERANCE UNDER 18 in .125 in 18 TO 36 in EXCLUSIVE .250 in 36 TO 50 in EXCLUSIVE .500 in

19、50 in AND OVER 1% TABLE 4 - WEIGHT (MAX) HOSE OR SLEEVE CODE HOSE OR TYPE SLEEVE UNITSSIZE.250SIZE.375SIZE.500SIZE .625 SIZE .750 SIZE 1.000 SIZE1.250- HOSE ONLY (REF - SEE AS5960) LB/IN .022 .037 .046 .070 .095 .160 .220 C TUBULAR FIRESLEEVE AS1072 (15 min) LB/IN .017 .020 .022 .030 .035 .040 .042

20、F ABRASION SLEEVE (AS1073-CODE B) LB/IN .003 .004 .005 .006 .008 .010 .015 H FIRESLEEVE INTEGRAL SILICONE LB/IN .040 .060 .070 .095 .140 .220 .265 ON HOSE (15 min) K ABRASION SLEEVE, POLYESTER LB/IN .025 .040 .050 .070 .110 .180 .230 ON HOSE NONE FIRESLEEVE CLAMP LB/EA .020 .025 .025 .025 .032 .032

21、.035 R LB/EA - .082 .137 .221 .270 .520 - NONE FITTING END (STRAIGHT) /17/ /18/ S LB/EA .052 .092 .162 .247 .296 .542 .850 E LB/EA .063 .114 .188 .300 .320 .645 - NONE FITTING END (45 ELBOW) /17/ /18/ R LB/EA - .101 .165 .261 .317 .615 - S LB/EA .063 .111 .189 .266 .342 .637 .955 E LB/EA .084 .140 .

22、230 .406 .425 .800 - AEROSPACE STANDARD AS5962 SHEET 4 OF 5 REV. A HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE CRES BRAID REINFORCED, 400 F, 5080 PSI FLARELESS, STRAIGHT TO 45 ELBOW TABLE 5 - INTEGRAL FIRESLEEVE CUFF DIMENSIONS /13/ HOSE SIZE G MAX H MAX 04 2.56 1.08 06 2.68 1.20 08 2.88 1.40 10 3.32 1.6

23、1 12 3.38 1.89 16 3.38 2.20 20 3.81 2.45 NOTES: 1. MATERIALS: a. HOSE AND FITTINGS - PER AS5960. b. THE COLLARS/SOCKETS MAY BE STAINLESS STEEL. c. SLEEVES - SEE APPLICABLE STANDARDS, TABLE 2. /2/ PROCUREMENT SPECIFICATION: AS5960 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFI

24、CATION SHALL BE MANUFACTURED AND ASSEMBLED BY AN ACCREDITED MANUFACTURER OR ASSEMBLED BY AN ACCREDITED DISTRIBUTOR LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS5960 FOR THIS STANDARD. SEE FOR CURRENT QPL ONLINE. 3. CONSTRUCTION AND PERFORMANCE PER AS5960.

25、 FITTINGS SHALL BE PERMANENTLY ATTACHED TO HOSE. 4. OPERATING CHARACTERISTICS PER AS5960. /5/ MARKING: MARKING SHALL BE PER AS5960 ON A STAINLESS STEEL BAND NOT OVER 1.0 IN WIDE OR ON THE COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 in HIGH. THE BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON TH

26、E HOSE TO PREVENT RELATIVE MOVEMENT AND RESULTANT CHAFING. IT SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. HOSE ASSEMBLY DATE AND “PT” SYMBOL SHALL BE PERMANENTLY MARKED ON THE BAND OR ON AN END FITTING OR A FIRESLEEVE CLAMP. /6/ LENGTH “L” IS A FOUR DIGIT NUMBER OF WHICH THE FIRST TH

27、REE DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE FOURTH DIGIT, THE FRACTION OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM “GAGE POINT” TO “GAGE POINT”. FOR LENGTH TOLERANCES SEE TABLE 3. TO CONVERT “GAGE POINT” TO “GAGE POINT” TO “END TO END” MEASUREMENT, ADD “D1” AND “D3“

28、FOR NAS1760 END STYLE, OR “D2“ AND “D4“ FOR AS4458 GLOBESEAL END STYLE TO LENGTH “L”. /7/ HOSE ASSEMBLY INSIDE DIAMETER SHALL BE VERIFIED BY PASSING THE DESIGNATED, OR LARGER, SPHERICAL BALL PER TABLE 1 THROUGH THE HOSE ASSEMBLY. /8/ DISTANCE ACROSS CORNERS OF COUPLING NUT AND NIPPLE OR SOCKET/COLLA

29、R HEX MAY EXCEED THIS DIMENSION. /9/ FITTING ENDS MUST COMPLY WITH NAS1760, AS4458, OR BE FUNCTIONALLY EQUIVALENT. DIMENSIONS D1, D3, AND D5 APPLY TO NAS1760 AND D2, D4, AND D6 APPLY TO AS4458. FITTINGS SHALL MATE WITH EN6123 OR AS5827. STANDARD COUPLING NUTS SHALL BE FUNCTIONALLY EQUIVALENT TO AS43

30、70 EXCEPT FOR THREAD AND WIRE GROOVE. THREADS AND WIRE GROOVE IN NUT, RETAINER WIRE, AND FITTING END WIRE GROOVE SHALL BE COATED WITH AS5272 TYPE 1 SOLID FILM LUBRICANT. /10/ DIAMETERS ARE LISTED FOR CLAMP SELECTION. /11/ THE TABLE 2 SLEEVE DIAMETERS FOR AS1072 SLEEV ES APPLY WHEN THE SLEEVE IS COMP

31、RESSED, OR CLAMPED TO CONTACT THE HOSE. IN THIS CASE A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE. AEROSPACE STANDARD AS5962 SHEET 5 OF 5 REV. A HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE CRES BRAID REINFORCED, 400 F, 5080 PSI FLARELESS, STRAIGHT TO 45 ELBOW /12/ THE CUT ENDS O

32、F THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER PRIOR TO INSTALLATION TO PREVENT WICKING OF FLUIDS. THE FIRESLEEVE ENDS SHALL BE SECURED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE, WHICH EXPOSE THE FIBERGLAS

33、S, SHALL BE COATED WITH RTV SILICONE RUBBER. /13/ THE ENDS OF THE INTEGRAL FIRESLEEVE AND FITTING SOCKET/COLLAR MAY BE COVERED WITH A SILICONE CUFF OR MOLDED SILICONE AS REQUIRED TO COMPLY WITH /14/ /14/ IDENTIFICATION MARKING: ADD “AS1055 TYPE IIb CLASS B-S/P” TO IDENTIFICATION MARKING TO SHOW LEVE

34、L OF COMPLIANCE, “FIREPROOF“ (15 MIN), WITH AS1055. /15/ INTEGRAL ABRASION SLEEVE SHALL FORM AN INTEGRAL PERMANENT PART OF THE HOSE AND SHALL TERMINATE A MAXIMUM OF .200 in FROM THE END OF THE COLLAR. /16/ THE SHRINK-ON POLYOLEFIN SLEEVE SHA LL COVER THE ENTIRE HOSE AND A MINIMUM OF 50% OF THE COLLA

35、RS ON BOTH ENDS OF THE ASSEMBLY. /17/ JUMP SIZE CODE EXPLANATION: a. R-STEP DOWN 1 STANDARD LETTER SIZE PER TABLE 1 (REDUCED). b. S-HOSE SIZE (NO REDUCTION OR EXPANSION) c. E-STEP UP 1 STANDARD LETTER SIZE PER TABLE 1 (EXPANDED) /18/ FITTING WEIGHTS ARE FOR REFERENCE ONLY. 19. DIMENSIONING AND TOLER

36、ANCING: ASME Y14.5M-1994. /20/ SAFETY WIRE HOLES LOCATION AND DIAMETER PER AS1043: L = TWO HOLES 180 APART UP TO 1.50 in HEX INCLUSIVE. THREE HOLES 120 APART FOR 1.625 in HEX AND LARGER. /21/ IN THE AREAS SHOWN, THE NUT OUTSIDE DIAMETER SHALL BE COLORED BLUE TO INDICATE 5080 PSI OPERATING PRESSURE A

37、ND EXTRA FINE THREAD. A PTFE OR FLUID RESISTANT PAINT SHALL BE USED. 22. EXAMPLE OF PART NUMBER: AS5962 H A 024 2 S E L SAFETY WIRE HOLES /20/ - ADD ONLY IF REQUIRED STRAIGHT FITTING /17/ STRAIGHT FITTING /17/FRACTIONAL LENGTH IN EIGHTS OF AN INCH, .25 in /6/ LENGTH IN WHOLE INCHES, 24 in /6/ HOSE O

38、R SLEEVE CODE. USE DASH (-) FOR BARE HOSE. SEE TABLE 2 BASIC HOSE ASSEMBLY SIZE, .50 in SEE TABLE 1 BASIC PART NUMBER 23. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.