SAE AS 5975C-2015 FITTING ASSEMBLY STRAIGHT MALE FLARELESS AXIALLY SWAGED HYDRAULIC 5080 PSI.pdf

1、AEROSPACE STANDARDFITTING ASSEMBLY, STRAIGHT, MALEFLARELESS, AXIALLY SWAGED,HYDRAULIC, 5080 PSIAS5975Copyright 2015 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p

2、hotocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2006-01REVISED2015-08THIRD

3、ANGLE PROJECTIONCUSTODIAN: G-3/G-3BREV.CFEDERAL SUPPLY CLASS4730AS5975SHEET 1 OF 4REV.CPROCUREMENT SPECIFICATION: AS5958 /4/SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isentirelyvoluntary, andits

4、applicability andsuitability foranyparticularuse,includingany patent infringementarisingtherefrom,is thesole responsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled.SAE invitesyourwrittencommentsandsuggestions.SAE val

5、ues your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5975CRATIONALECORRECTED “2016” AND “W4” FOR 2016 AND 1620, ADDED NOTE 15, AND UPDATED NOTE 14 AND FIGURE.FIGURE 1 - STRAIGHT, MALE FLARELESS, AXIAL SWAGE(SEE TABLES 1A AND 1B FOR DIMENSI

6、ONAL INFORMATION)AEROSPACE STANDARDAS5975SHEET 2 OF 4REV.CFITTING ASSEMBLY, STRAIGHT, MALEFLARELESS, AXIALLY SWAGED,HYDRAULIC, 5080 PSITABLE 1A - DIMENSIONS A THROUGH JBASIC NO.AS5975 /13/SIZE CODENOMINALTUBE SIZEEND 1NOMINALTUBE SIZEEND 2AMAXA1MAXEMAXFMIN (H)J /10/TUBE DEDUCT0404 .2500 .2500 1.247

7、1.160 .466 .253 .438 .665 .1500604 .3750 .2500 1.278 1.191 .466 .253 .563 .696 .1500406 .2500 .3750 1.477 1.361 .609 .378 .563 .678 .1500606 .3750 .3750 1.493 1.377 .609 .378 .563 .694 .1500806 .5000 .3750 1.566 1.450 .609 .378 .750 .767 .1500608 .3750 .5000 1.717 1.571 .783 .504 .750 .718 .1750808

8、5000 .5000 1.810 1.664 .783 .504 .750 .811 .1751008 .6250 .5000 1.877 1.731 .783 .504 .875 .878 .1750810 .5000 .6250 2.112 1.908 .939 .629 .875 .819 .1751010 .6250 .6250 2.171 1.967 .939 .629 .875 .878 .1751210 .7500 .6250 2.258 2.054 .939 .629 1.063 .965 .1751012 .6250 .7500 2.346 2.141 1.122 .754

9、 1.063 .909 .1751212 .7500 .7500 2.391 2.186 1.122 .754 1.063 .954 .1751612 1.0000 .7500 2.435 2.230 1.122 .754 1.313 .998 .1751216 .7500 1.0000 2.733 2.519 1.495 1.004 1.313 1.005 .2001616 1.0000 1.0000 2.697 2.483 1.495 1.004 1.313 .969 .2002016 1.2500 1.0000 2.733 2.519 1.495 1.004 1.625 1.005 .2

10、001620 1.0000 1.2500 3.025 2.801 1.758 1.255 1.625 1.014 .2002020 1.2500 1.2500 2.999 2.775 1.758 1.255 1.625 .988 .200TABLE 1B - DIMENSIONS W THROUGH W4 AND WEIGHTSBASIC NO.AS5975 /13/SIZE CODENOMINALTUBE SIZEEND 1NOMINALTUBE SIZEEND 2T THREADPER AS8879WMINW1MAXW2.0015W3MAXW4MAXWEIGHTLB/EAAPPROX RE

11、F0404 .2500 .2500 .4375-28 UNJEF-3A .123 .488 .3005 .018 .065 .0170604 .3750 .2500 .5625-24 UNJEF-3A .123 .488 .3005 .018 .065 .0240406 .2500 .3750 .4375-28 UNJEF-3A .153 .675 .4475 .033 .065 .0260606 .3750 .3750 .5625-24 UNJEF-3A .153 .675 .4475 .033 .065 .0290806 .5000 .3750 .7500-20 UNJEF-3A .153

12、 .675 .4475 .033 .065 .0470608 .3750 .5000 .5625-24 UNJEF-3A .165 .871 .5945 .033 .065 .0450808 .5000 .5000 .7500-20 UNJEF-3A .165 .871 .5945 .033 .129 .0631008 .6250 .5000 .8750-20 UNJEF-3A .165 .871 .5945 .033 .129 .0720810 .5000 .6250 .7500-20 UNJEF-3A .140 1.190 .7365 .021 .078 .0821010 .6250 .6

13、250 .8750-20 UNJEF-3A .140 1.190 .7365 .021 .078 .1001210 .7500 .6250 1.0625-18 UNJEF-3A .140 1.190 .7365 .021 .078 .1201012 .6250 .7500 .8750-20 UNJEF-3A .154 1.327 .8805 .024 .089 .1321212 .7500 .7500 1.0625-18 UNJEF-3A .154 1.327 .8805 .024 .089 .1401612 1.0000 .7500 1.3125-16 UNJ-3A .154 1.327 .

14、8805 .024 .089 .1801216 .7500 1.0000 1.0625-18 UNJEF-3A .167 1.612 1.1725 .027 .099 .2601616 1.0000 1.0000 1.3125-16 UNJ-3A .167 1.612 1.1725 .027 .099 .2602016 1.2500 1.0000 1.6250-16 UNJ- 3A .167 1.612 1.1725 .027 .099 .3251620 1.0000 1.2500 1.3125-16 UNJ-3A .185 1.886 1.4345 .030 .113 .3552020 1.

15、2500 1.2500 1.6250-16 UNJ- 3A .185 1.886 1.4345 .030 .113 .375AEROSPACE STANDARDAS5975SHEET 3 OF 4REV.CFITTING ASSEMBLY, STRAIGHT, MALEFLARELESS, AXIALLY SWAGED,HYDRAULIC, 5080 PSINOTES:/1/ MATERIAL:CODE LETTER “T“RING - AMS4965 TITANIUM ALLOY, 6.0Al - 4.0V SOLUTION HEAT TREATED AND AGED OR AMS4928

16、TITANIUM ALLOY 6.0Al - 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT.BODY - AMS4928 TITANIUM ALLOY, 6.0Al - 4.0V ANNEALED.2. FINISH:TITANIUM - NONE REQUIRED./3/ COATINGS/LUBRICANTS /14/:a. NO SUFFIX CODE LETTER(1) RING: THE OUTER SURFACE SHALL HAVE A .125 INCH MIN

17、IMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. BLUE PTFE COATING OR PAINT SHALL BE RESISTANT TO AS1241 FLUID WHEN USED. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958.(2) BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR P

18、ER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT SHALL BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID.b. SUFFIX CODE LETTER “B”(1) RINGS - THE OUTER SURFACE SHALL HAVE A .125 INCH MINIMUM WIDTH BLUE ANODIZED RING OR COM

19、PLETELY ANODIZED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATING PRESSURE. MARKING METHODS SHALL BE IN ACCORDANCE WITH AS5958.(2) BODY - LEAD FREE SOLID FILM LUBRICANT PER AS5272 TYPE I OR II, OR PER AS6449 TYPE III OR IV, PTFE OR PETROLEUM-BASED LUBRICANT SHALL BE APPLIED TO PORTIONS OF THE ID AND OD.

20、THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID./4/ PROCUREMENT SPECIFICATION: AS5958 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED AND ASSEMBLED BY AN ACCREDITED MANUFACTURER OR ASSEMBLED BY AN ACCREDITED DISTRIBUTOR L

21、ISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI QPL-AS5958 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ON-LINE.5. DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO

22、ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION./6/ IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON THE RING.7. FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959. THE AFTER SWAGE ACCEPTABILITY LIMIT DIMENSION “Z“ FOR EACH PORT SIZE IS DEFINED IN AS5959.8. SURFAC

23、E TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PERASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES SHALL BE 125 MICROINCHES Ra.9. DIMENSIONS AND TOLERANCES: ASME Y14.5M.-1994.a. DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED.b. DIMENSIONAL TOLERANCES SHALL BE .005 INCH UNLESS OTHERW

24、ISE SPECIFIED.c. ANGULAR TOLERANCES SHALL BE .50q UNLESS OTHERWISE SPECIFIED.d. BREAK ALL EDGES .003 TO .010 INCH UNLESS OTHERWISE SPECIFIED.AEROSPACE STANDARDAS5975SHEET 4 OF 4REV.CFITTING ASSEMBLY, STRAIGHT, MALEFLARELESS, AXIALLY SWAGED,HYDRAULIC, 5080 PSI/10/ THIS DIMENSION IS THE ALLOWABLE TUBE

25、 END POSITIONING FOR SYSTEM LAYOUT DESIGN./11/ DIMENSION “A” IS THE FITTING ASSEMBLY LENGTH AND “A1” IS THE FITTING BODY LENGTH BEFORE SWAGE.12. INTERPRETATION OF DRAWING PER AS4296./13/ EXAMPLE OF PART NUMBER:AS5975 T 0806 BRING COATING CODE /3/ /14/BASIC PART NUMBER NO CODE LETTER /3a/1/ MATERIAL

26、CODE BLUE PTFE COATINGTUBE SIZE IN .0625 INCH OR PAINT ON RINGINCREMENTS (08 = .500 INCH) CODE LETTER “B” /3b/(END 1 - FLARELESS & END 2 - SWAGE) BLUE ANODIZED RING14/ NO CODE LETTER PARTS ARE NOT RECOMMENDED FOR PROCUREMENT AFTER 2015/9/30 AND SHOULD BE REPLACED BY ANODIZED PARTS WITH CODE LETTER “

27、B”. BLUE ANODIZED RING CODE “B” PARTS MAY BE ORDERED IN LIEU OF NO CODE PARTS.15. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION.16. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNIC

28、AL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.