SAE AS 6047C-2018 FITTING UNION STANDARD AND REDUCER BULKHEAD FLARELESS PRECISION TYPE.pdf

1、 AEROSPACE STANDARD FITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS, PRECISION TYPE AS6047Copyright 2018 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p

2、hotocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2009-12REVISED2018-01THI

3、RD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS6047 SHEET 1 OF 4 REV. C PROCUREMENT SPECIFICATION: AS18280 /5/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report i

4、s entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SA

5、E invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS6047C RATIONALE ADDED CONDUCTIVE HIGH PURITY ALUMINUM COATING FOR ALUMINUM ALLOY FITTINGS. FIGURE 1 - FITTING, UNION, STANDARD AND REDUCER, BULK

6、HEAD END, NON-REDUCER SHOWN TABLE 1 - OVERALL LENGTH A /9/ /11/ SIZE OF PORT #2 SIZE OF PORT #1 02 03 04 05 06 08 10 12 14 16 20 24 32 .010 .010 .010 .010 .010 .010 .010 .010 .010 .010 .010 .010 .010 02 1.484 1.516 1.578 1.609 1.703 1.844 2.000 2.156 2.156 2.156 2.156 2.156 2.422 03 1.516 1.563 1.62

7、5 1.656 1.750 1.891 2.047 2.203 2.203 2.203 2.203 2.203 2.469 04 1.547 1.594 1.656 1.688 1.781 1.922 2.078 2.234 2.234 2.234 2.234 2.234 2.500 05 1.578 1.625 1.688 1.688 1.781 1.922 2.078 2.324 2.234 2.234 2.234 2.234 2.500 06 1.641 1.688 1.750 1.750 1.797 1.938 2.094 2.250 2.250 2.250 2.250 2.250 2

8、.516 08 1.734 1.781 1.844 1.844 1.891 2.031 2.188 2.344 2.344 2.344 2.344 2.344 2.609 10 1.813 1.859 1.922 1.922 1.969 2.109 2.250 2.406 2.406 2.406 2.406 2.406 2.672 12 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.484 2.469 2.469 2.469 2.469 2.734 14 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2

9、.469 2.469 2.469 2.469 2.734 16 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469 2.734 20 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469 2.734 24 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469 2.734 32 1.984 2.031 2.094 2.094 2

10、.141 2.281 2.422 2.531 2.531 2.531 2.531 2.531 2.734 AEROSPACE STANDARD AS6047 SHEET 2 OF 4 REV. C FITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS, PRECISION TYPE TABLE 2 - HOLE DEPTH Y /9/ /11/ SIZE OF PORT #2 SIZE OF PORT #1 02 03 04 05 06 08 10 12 14 16 20 24 32 02 - - - - - - - - - - -

11、 - - 03 .469 - - - - - - - - - - - - 04 .484 .484 - - - - - - - - - - - 05 .500 .500 .516 - - - - - - - - - - 06 .547 .531 .562 .562 - - - - - - - - - 08 .594 .594 .625 .625 .641 - - - - - - - - 10 .656 .656 .672 .672 .703 .672 - - - - - - - 12 .719 .719 .734 .750 .766 .750 .750 - - - - - - 14 .688

12、.688 .704 .719 .735 .719 .719 .861 - - - - - 16 .656 .656 .672 .672 .703 .688 .688 .719 .688 - - - - 20 .594 .594 .609 .609 .641 .625 .625 .656 .625 .703 - - - 24 .516 .516 .531 .547 .562 .641 .656 .578 .547 .641 .656 - - 32 .453 .438 .469 .469 .469 .469 .469 .516 .485 .562 .578 .656 - TABLE 3 - HOL

13、E DEPTH Z /9/ /11/ SIZE OF PORT #2 SIZE OF PORT #1 02 03 04 05 06 08 10 12 14 16 20 24 32 02 - 1.016 1.062 1.078 1.156 1.250 1.391 1.500 1.477 1.438 1.375 1.297 1.438 03 - - 1.047 1.078 1.141 1.250 1.391 1.500 1.471 1.422 1.375 1.297 1.422 04 - - - 1.094 1.172 1.281 1.406 1.516 1.494 1.453 1.391 1.3

14、12 1.453 05 - - - - 1.172 1.281 1.422 1.531 1.500 1.453 1.391 1.328 1.453 06 - - - - - 1.297 1.438 1.547 1.523 1.391 1.422 1.344 1.484 08 - - - - - - 1.453 1.562 1.533 1.484 1.438 1.359 1.391 10 - - - - - - - 1.562 1.537 1.500 1.438 1.359 1.500 12 - - - - - - - - 1.574 1.531 1.468 1.406 1.531 14 - -

15、 - - - - - - - 1.566 1.503 1.430 1.559 16 - - - - - - - - - - 1.516 1.453 1.562 20 - - - - - - - - - - - 1.468 1.594 24 - - - - - - - - - - - - - 32 - - - - - - - - - - - - - TABLE 4 - TUBE SIZE AND CORRESPONDING THREAD PORT SIZE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3A 02 .125 .3125-24 UNJF

16、 03 .188 .3750-24 UNJF 04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF 08 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ 14 .875 1.1875-12 UNJ 16 1.000 1.3125-12 UNJ 20 1.250 1.6250-12 UNJ 24 1.500 1.8750-12 UNJ 32 2.000 2.5000-12 UNJ AEROSPACE STANDARD AS6047 SHEET

17、 3 OF 4 REV. C FITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS, PRECISION TYPE TABLE 5 - HEX DIMENSION AND WEIGHTS /9/ /10/ BASIC NO. AS6047 /21/ LARGEST PORT SIZE CODE B .010 H LB/EA APPROX REF ALUM LB/EA APPROX REF STEEL LB/EA APPROX REF TI 02 .542 .552- .565 .00990 .0279 .0153 03 .605 .

18、615- .628 .0162 .0432 .0243 04 .668 .678- .691 .0207 .0558 .0315 05 .730 .740- .753 .0261 .0702 .0405 06 .792 .802- .815 .0315 .0855 .0486 08 .980 .990-1.003 .0576 .158 .0900 10 1.103 1.113-1.128 .0810 .210 .126 12 1.353 1.363-1.380 .120 .325 .187 14 1.478 1.488-1.505 - - - 16 1.603 1.613-1.630 .182

19、 .437 .286 20 1.853 1.863-1.880 .224 .610 .332 24 2.099 2.109-2.225 .266 .733 .422 32 2.724 2.734-2.760 - - - NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER

20、 T TYPE 6Al-4V TITANIUM ALLOY PER PROCUREMENT SPECIFICATION b. CODE LETTER V TYPE 15-5PH CORROSION RESISTANT STEEL PER PROCUREMENT SPECIFICATION c. CODE LETTER W TYPE 7075-T73 OR 7075-T7351 ALUMINUM ALLOY BAR PER PROCUREMENT SPECIFICATION 2. HEAT TREATMENT: a. MATERIAL CODE LETTER T ANNEALED PER PRO

21、CUREMENT SPECIFICATION b. MATERIAL CODE LETTER V AGE TO CONDITION H1075 PER PROCUREMENT SPECIFICATION c. MATERIAL CODE LETTER W ELECTRICAL CONDUCTIVITY AND HARDNESS PER PROCUREMENT SPECIFICATION /3/ FINISH: a. MATERIAL CODE LETTER T ANODIZE OR FLUORIDE PHOSPHATE CONVERSION COAT PER PROCUREMENT SPECI

22、FICATION b. MATERIAL CODE LETTER V: (1) V CODE PARTS TO BE PASSIVATED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: PASSIVATE PER PROCUREMENT SPECIFICATION. (2) V CODE PARTS TO BE CADMIUM PLATED ONLY SHALL HAVE THE FINISH CODE LETTER “P” AFTER THE S

23、IZE CODE IN THE PART NUMBER. THE FINISH WILL BE: CADMIUM PLATE PER PROCUREMENT SPECIFICATION. c. MATERIAL CODE LETTER W (1) W CODE PARTS TO BE ANODIZED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE ANODIZE PER PROCUREMENT SPECIFICATION. (2) W CODE PA

24、RTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE CODE IN THE PART NUMBER. SEE PROCUREMENT SPECIFICATION FOR REQUIREMENTS. AEROSPACE STANDARD AS6047 SHEET 4 OF 4 REV. C FITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS, PRECISION TYPE /4/ OXY

25、GEN SYSTEM AND COMPONENT CLEANING, SUFFIX LETTER A /21/: a. MATERIAL CODE LETTER V CLEAN AND PACKAGE PER ARP1176 CATEGORY 1C b. MATERIAL CODE LETTER W CLEAN AND PACKAGE PER ARP1176 CATEGORY 2 /5/ PROCUREMENT SPECIFICATION: AS18280, UNLESS OTHERWISE SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THI

26、S SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS18280 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNECTION SYSTEMS WITH

27、NOMINAL OPERATING PRESSURES AS SPECIFIED IN AS18280. ADDITIONAL CRITERIA - FOR REDUCER CONFIGURATIONS THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 7. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 8. THE HEX CORNERS MAY BE ROUNDED PER ARP1942. /9/ THE DIMENSIONS IN THE TABLES 1 THRO

28、UGH 5 ARE FOR FINAL MACHINED PARTS. THE BAR SIZE IS DETERMINED AS THE SIZE NECESSARY TO MAKE THE LARGEST FITTING END. /10/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER FITTINGS WILL HAVE LOWER WEIGHTS. /11/ REDUCER FITTINGS WHICH FALL IN THE SHADED AREA OF TABLES 1, 2, AND 3 SHOULD BE AVOIDED. IF THEY

29、 MUST BE USED, SPECIAL ATTENTION SHOULD BE GIVEN TO CLAMPING OR OTHER MEANS TO PROTECT THE SMALLER PORT OR TUBE. 12. FITTING IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS18280. /13/ FINISH CODE LETTER P SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE V PARTS THAT ARE TO BE CADMIUM PLATED. SU

30、FFIX CODE LETTER A SHALL NOT BE COMBINED WITH FINISH CODE LETTER P. FINISH CODE LETTER V SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE W PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUM TO PROVIDE LOW ELECTRICAL CONTACT RESISTANCE. SUFFIX CODE LETTER A MAY BE COMBINED WITH FINISH CODE

31、 LETTER V AND SHALL BE SPECIFIED AS VA. 14. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE D

32、OCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 15. INTERPRETATION OF DRAWING PER AS4296. 16. FLUID PASSAGE, HOLE CONTOUR PER AS4266. 17. INVEN

33、TORIED PARTS CONFORMING TO THE PREVIOUS ISSUE MAY BE USED TO DEPLETION. 18. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. SURFACES OF HEX FLATS MAY BE 250 MICROINCHES Ra. 19. DIMENSIONING AND TOLERANCIN

34、G: ASME Y14.5M-1994. 20. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 030. /21/ EXAMPLES OF PART NUMBERS: AS6047 W 08 08 V A BASIC PART NUMBER MATERIAL CODE LETTER /1/ SIZE CODE FOR PORT 1 IN .062 INCREMENTS SIZE CODE FOR PORT 2 IN .062 INCREMENTS SUFFIX CODE LETTER /4/ FINISH CODE LETTER /3/ /13/