SAE AS 6075-2011 FITTING BOLT FLARED 37 PHERICAL《37球面螺栓扩口接头》.pdf

1、AEROSPACE STANDARD FITTING, BOLT, FLARED, 37 SPHERICAL AS6075Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, w

2、ithout the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2011-05THIRD ANGLE PROJECTION CUSTODIAN: SAE G3/G3B FEDERAL SU

3、PPLY CLASS 4730 AS6075SHEET 1 OF 4PROCUREMENT SPECIFICATION: /4/ AS6076SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany part

4、icular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feed

5、backon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6075RATIONALE THIS SAE AEROSPACE STANDARD (AS) ESTABLISHES THE REQUIREMENTS FOR THE BOLT FITTING WITH 37 DEGREE SPHERICAL FLARED TUBE. FIGURE 1 - FITTING, BOLT AEROSPACE STANDARD AS6075SHEET 2 OF 4FITTING, BOLT, FLARE

6、D, 37 SPHERICAL TABLE 1A - DIMENSIONS BASIC NO. AS6075/13/SIZE CODE (NOMINAL TUBE SIZE)T THREAD PER AS8879 CLASS 3A A B.010 C D E.010 F.002 04 .250 .4375-20 UNJF 1.922 .668 .438 1.188 .781 .433 05 .312 .5000-20 UNJF 1.922 .730 .438 1.188 .781 .496 06 .375 .5625-18 UNJF 2.125 .792 .469 1.344 .875 .55

7、8 08 .500 .7500-16 UNJF 2.594 .980 .562 1.688 1.094 .746 10 .625 .8750-14 UNJF 3.000 1.103 .594 1.969 1.250 .871 12 .750 1.0625-12 UNJ 3.484 1.352 .656 2.312 1.468 1.058 16 1.000 1.3125-12 UNJ 4.094 1.603 .656 2.812 1.687 1.308 TABLE 1B - DIMENSIONS AND WEIGHTS BASIC NO. AS6075/13/SIZE CODE H J.005

8、L M N LB/EAAPPROX. REF ALLB/EAAPPROX. REF STEELLB/EAAPPROX.REF TI04 .678- .691 .474 .344 .188 .168-.175 .0287 .0825 .0455 05 .740- .753 .536 .406 .219 .230-.237 .0343 .0985 .0543 06 .802- .815 .599 .469 .250 .293-.301 .0448 .129 .0710 08 .990-1.003 .786 .625 .312 .387-.395 .0937 .269 .148 10 1.113-1

9、.128 .911 .750 .375 .480-.488 .138 .397 .219 12 1.363-1.380 1.099 .938 .438 .604-.614 .230 .662 .365 16 1.613-1.630 1.349 1.188 .625 .839-.851 .359 1.03 .569 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT OFFICIALS IF YOU HAVE QUESTIONS CONCERNING

10、 CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER F - TYPE 4130 PER AMS6370 OR TYPE 4140 PER AMS6382. /2/ b. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5639. c. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5648. d. CODE LETTER R - TYPE 32

11、1 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5645. e. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928. f. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124. AEROSPACE STANDARD AS6075SHEET 3 OF 4FITTING, BOLT, FL

12、ARED, 37 SPHERICAL /2/ HEAT TREATMENT: a. MATERIAL CODE LETTER F - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTER W SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. c. OTHER MATERIAL CODE LETTERS - NONE. 3. FINISH: a. MATERIAL CODE

13、LETTER F - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS J, K, AND R - PASSIVATE PER AMS2700, TYPE 6 OR 7. c. MATERIAL CODE LETTER T - ANODIZE PER AMS2488 OR FLUORIDE PHOSPHATE CONVERSION COAT PER

14、 AMS2486 WITH COLOR PER PROCUREMENT SPECIFICATION. d. MATERIAL CODE LETTER W: 1. ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE

15、CODE IN THE PART NUMBER. HIGH PURITY ALUMINUM COAT PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: AS6076 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRA

16、CTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT ./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” A

17、ND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. SIZES 04 THROUGH 12 IN ALUMINUM ALLOY AND SIZES 04 THR

18、OUGH 16 IN STEEL AND TITANIUM ALLOY AT 3000 psi. b. SIZES 04 THROUGH 16 IN ALUMINUM ALLOY AT 1500 psi. /7/ THE HEX CORNERS MAY BE ROUNDED PER ARP1942. 8. INTERPRETATION OF DRAWING PER ARP4296. 9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACH

19、INED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 12. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 3

20、0. AEROSPACE STANDARD AS6075SHEET 4 OF 4FITTING, BOLT, FLARED, 37 SPHERICAL /13/ EXAMPLE OF PART NUMBER: THE FINISH CODE LETTER “V” WILL BE PLACED HERE ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUMAS6075 W 08 VBASIC PART NUMBER SIZE CODE, TUBE SIZE IN .062 INCREMENTSMATERIAL CODE LETTER /1/