ImageVerifierCode 换一换
格式:PDF , 页数:29 ,大小:2.44MB ,
资源ID:1025118      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1025118.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SAE AS 6171 6-2016 Techniques for Suspect Counterfeit EEE Parts Detection by Acoustic Microscopy (AM) Test Methods.pdf)为本站会员(ownview251)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SAE AS 6171 6-2016 Techniques for Suspect Counterfeit EEE Parts Detection by Acoustic Microscopy (AM) Test Methods.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments andsuggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this public

3、ation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outs

4、ide USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on thisTechnical Report, please visithttp:/standards.sae.org/AS6171/6AEROSPACESTANDARDAS6171/6Issued 2016-10Techniques for Suspect/Counterfeit EEE Parts Detection by Aco

5、ustic Microscopy (AM) Test MethodsRATIONALEThis document provides guidance and requirements on the Acoustic Microscopy (AM) test procedures to be employed by the Test Laboratory (Lab) for the non-destructive AM testing of parts for suspect counterfeit (SC) part detection. The level of testing shall

6、be derived by the User Organization working in conjunction with the Test Lab, taking into consideration the risk level as defined in the SC part detection flow specified herein. It shall be the responsibility of the Test Lab to conduct the AM test following the sequence of inspections for a given ri

7、sk level specified herein. The creation of this document is a step in addressing the ever-increasing global problem of electronic parts counterfeiting.INTRODUCTIONBecause many methods of counterfeiting of electronics involve a change of material from the original part, AM can provide a method of ins

8、pection of parts and detecting differences in their material composition. The method has been used extensively to detect non-conforming parts in electronics and in many other product areas. The implementation of Restriction of Hazardous Substances (RoHS) requirements of the European Union and simila

9、r laws in other countries, resulted in wide spread use of AM techniques to confirm that electronic parts are not damaged while subjected to a surface mount to a PCB process. This document provides techniques based on those practices to detect Suspect counterfeit parts.The part photographs contained

10、herein are provided to illustrate the application of detection methods identified in the document, and are by no means intended to imply that a manufacturer identified in a photograph is involved with the suspect product.TABLE OF CONTENTS1. SCOPE . 31.1 Purpose 32. REFERENCES . 32.1 Applicable Docum

11、ents . 32.1.1 SAE Publications 32.2 Related Publications 32.3 Terms and Definitions 42.4 Acronyms . 43. DESCRIPTION OF METHODOLOGY/PROCEDURE . 43.1 Material Control/ESD Handling 43.2 Additional Considerations 43.2.1 Microfocus Radiology versus AM . 43.2.2 Infrared versus AM . 43.3 General Considerat

12、ions . 43.3.1 How AM Works 4SAE INTERNATIONAL AS6171/6 Page 2 of 293.4 AM Procedure for PEMS and BGAs 73.4.1 General Considerations . 73.4.2 Exterior AM Inspection (Near Surface AM Imaging) 73.4.3 Interior AM Inspections 93.4.4 Percentage Delamination Calculations (Figure 3) . 104. TEST EQUIPMENT AN

13、D CALIBRATION 114.1 Controls and Calibration . 115. REQUIREMENT . 115.1 Sampling 115.2 Categories of Testing/Risk Levels . 115.3 Testing Requirements and Minimum Risk Level . 115.4 Counterfeit Detection Test Sequence 115.5 Test Plan 125.6 Analysis and Interpretation of Results . 125.7 Test Report 12

14、5.8 Certification and Training . 135.8.1 Personnel . 135.8.2 Laboratory/Test Facility 155.8.3 Proficiency 155.9 Data Retention Requirements 165.9.1 Report Retention 166. NOTES . 166.1 Revision Indicator . 16APPENDIX A ACOUSTIC MICROSCOPY IMAGES 17FIGURE 1 DIAGRAM OF REFLECTIVE MODE ACOUSTIC MICROSCO

15、PY 5FIGURE 2 DIAGRAM OF TRANSMISSION MODE ACOUSTIC MICROSCOPY 5FIGURE 3 EXAMPLE OF PERCENTAGE DELAMINATION CALCULATIONS . 10TABLE 1 AM TEST REQUIREMENTS BASED ON RISK LEVEL 11SAE INTERNATIONAL AS6171/6 Page 3 of 291. SCOPEThrough the use of ultra-high frequency ultrasound, typically above 10 MHz, Ac

16、oustic Microscopy (AM) non-destructively finds and characterizes physical features and latent defects (visualization of interior features in a layer by layer process) -such as material continuity and discontinuities, sub-surface flaws, cracks, voids, delaminations and porosity. AM observed features

17、and defects can be indicators that the components were improperly handled, stored, altered or previously used.If AS6171/6 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.1.1 Purpose The purpose of this document is to provide recommended techniques and guid

18、elines for the use of Acoustic Microscopy for detection of counterfeit electronic components.2. REFERENCES2.1 Applicable DocumentsThe following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other pu

19、blications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specif

20、ic exemption has been obtained.2.1.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.AS6171 Test Methods Standard; General Requirements, Suspect/Counterfeit, E

21、lectrical, Electronic, and Electromechanical Parts2.2 Related PublicationsThe following publications are provided for information purposes only and are not a required part of this SAE Aerospace Technical Report.MIL-STD-883, Method 2030 Ultrasonic Inspection of Die AttachNASA PEM-INST-001 Instruction

22、s for Plastic Encapsulated Microcircuit (PEM) Selection, Screening, and QualificationJ-STD-020 Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount DevicesJ-STD-035 Acoustic Microscopy for Nonhermetic Encapsulated Electronic ComponentsMIL-STD-1580 Destructive Physical

23、 Analysis for Electronic, Electromagnetic, and Electromechanical PartsESA/SCC No. 25200 Application of Scanning Acoustic Microscopy to Plastic Encapsulated DevicesGEIA-STD-006 Requirements for Using Solder Dip to Replace the Finish on Electronic Piece PartsSAE INTERNATIONAL AS6171/6 Page 4 of 292.3

24、Terms and DefinitionsSee section 2.2 of AS6171 General Requirements.2.4 AcronymsSee section 2.3 of AS6171 General Requirements.3. DESCRIPTION OF METHODOLOGY/PROCEDURE3.1 Material Control/ESD Handling3.1.1 Parts subjected to handling during AM testing can be damaged by ESD. Therefore, the ESD control

25、 requirementsof section 3.9.5 of AS6171 General Requirements shall be followed.3.2 Additional Considerations3.2.1 Microfocus Radiology versus AMAM and microfocus radiology are complementary techniques that are frequently found in the same laboratories and they can reveal different features. Radiolog

26、y relies on differential attenuation of the X-ray energy. AM relies on material change. The practical result is that AM is orders of magnitude more sensitive for detecting air space type defects such as voids, delaminations and cracks.3.2.2 Infrared versus AM Infrared is an inspection technique that

27、 is based on how the infrared energy transmits through a material. Since air space type defects do not transmit the infrared energy as well as continuous material, this technique is sometimes used to inspect for voids and delaminations. Although this technique can produce a picture very quickly, it

28、is highly limited by the materials under inspection and the details achievable. AM on the other hand, takes a little longer to generate an image but the practical result is that the images are of much higher detail. Plus, AM is not limited by the materials under inspection.3.3 General Considerations

29、3.3.1 How AM Works3.3.1.1 Reflection Mode (Figure 1) - As per J-STD-035Acoustic Microscopy for Nonhermetic Encapsulated Electronic Components, AM has the ability to create images by generating a pulse of ultrasound, which is focused to a pinpoint spot. The pulse is directed into a sample and reflect

30、ed at interfaces. The frequency of the pulses and design of the lens are chosen to optimize spot size (resolution) and depth penetration for each application. In the reflection mode of operation, the same transducer is used to send and receive the ultrasonic pulse. Return echoes arrive at different

31、times based upon the depth of the reflecting feature and the velocity of sound in the materials. The operator positions an electronic gate to capture the depth of interest. The amount of ultrasound reflected at the interface is based on differences in the acoustic impedances of the materials at the

32、interface. Greater differences in the acoustic impedances of the materials at the interface produce higher amplitudes of reflected ultrasound. The order of the acoustic impedances, going from one material to the other, will change the polarity/phase of the reflected ultrasound, too. In general, goin

33、g from a lower to higher acoustic impedance will have a stronger positive reflection and going from a higher to lower will have a stronger negative reflection. In addition, changes in the reflectedsignal can provide evidence of changes in material properties. This data is often the key to determinin

34、g variations in materials used and manufacturing processes.SAE INTERNATIONAL AS6171/6 Page 5 of 29Figure 1 - Diagram of reflective mode acoustic microscopy3.3.1.2 Transmission Mode (Figure 2) - As per J-STD-035Acoustic Microscopy for Nonhermetic Encapsulated Electronic Components, AM also has the ab

35、ility to create images based on how the ultrasound transmits through the entire sample thickness. Since air space defects such as voids, delaminations, cracks and porosity cannot transmit ultrasound, the loss of transmitted signal indicates the presence of these types of defects. In addition, change

36、s in the transmitted signal can provide evidence of changes in material properties. This data is often the key to determining variations in materials used and manufacturing processes.Figure 2 - Diagram of transmission mode acoustic microscopySAE INTERNATIONAL AS6171/6 Page 6 of 293.3.1.3 AM Microele

37、ctronic Product Applications Relative to Counterfeit Detection1. Plastic Encapsulated Microcircuits (PEMs)2. Plastic Ball Grid Arrays (BGAs)3. Ceramic Chip Capacitors4. Die Attach5. Chip Scale Packages (CSPs)6. Flip Chips7. Stacked Dies8. Ceramic Ball Grid Arrays (CBGAs)9. Tape Automated Bond (TAB)1

38、0. Hybrids, MCMs, SIPs11. Flex Circuits12. Printed Circuit Boards (PCBs)13. Smart Cards14. Bonded Wafers15. Thermo Electric Coolers (TECs)16. Power Modules3.3.1.4 Materials AM Technology is Effective for Relative to Counterfeit Detection1. Glass2. Ceramics3. Plastics4. Adhesives5. Metals6. Fiberglas

39、s7. Polymers8. Graphite9. Metal Matrix10. CompositesSAE INTERNATIONAL AS6171/6 Page 7 of 293.4 AM Procedure for PEMS and BGAs3.4.1 General ConsiderationsThe following shall be considered prior to and after obtaining the AM image; refer to the equipment manufacturersinstructions for optimum equipment

40、 settings.1. Transducer selectiona. Frequency (MHz)b. Focal Length (FL) in water c. F# (FL/Diameter of Piezoelectric Element)d. Reflection and/or Transmission Mode imaginge. Parallelism of transducer scan plane and surface of part being scanned2. Focal Depth(s) desired within the sample3. Are there

41、any AM “Reference“ images of known good parts available from the manufacturer or other reliable source?4. Examine image for anomalies (refer to 3.4.2 and 3.4.3)5. Calculate percentage of defects per critical interfaces (refer to 3.4.4)6. Record all information required in the Test Report (refer to 5

42、.7)3.4.2 Exterior AM Inspection (Near Surface AM Imaging) 3.4.2.1 Metal Lead Frame Based PackagesThis section defines the potential exterior defects which may indicate that a device is counterfeit. These defects do not necessarily mean the devices are counterfeit and should be used with other availa

43、ble data to determine whether a device is counterfeit. In some cases, additional visual or other testing (electrical, DDPA, etc.) may need to be done to conclusively determine if a device is a counterfeit.There are several indicators that a device may be counterfeit. These indicators are listed in 3

44、.4.2.1.1 through 3.4.2.1.8.For each of these indicators, the evidence which could be obtained from an acoustic image is identified. Wherever possible, a visual example of this type of defect using AM is referenced in Appendix A. 3.4.2.1.1 Evidence of Mishandling1. Voids2. Pits (see Appendix A, Figur

45、e A11)3. Scratches (see Appendix A, Figure A12)4. Pry Marks3.4.2.1.2 Evidence of Ghost Marking (see Appendix A, Figure A13)SAE INTERNATIONAL AS6171/6 Page 8 of 293.4.2.1.3 Evidence of Sanding 1. Sanding marks seen through blacktop layer (see Appendix A, Figure A1)2. Inconsistent edge shape distortio

46、ns seen at a corner(s) (see Appendix A, Figure A2)3. Partial removal of Pin-One dimple3.4.2.1.4 Evidence of Blacktop Coating1. Uneven blotchy surface image (see Appendix A, Figure A14)2. Overspray in Pin-One cavity (see Appendix A, Figure A15)3. Significant, measurable contrast (gray scale gain) bet

47、ween front and back component scans (see Appendix A, Figure A16)4. Foreign particles encapsulated within the coating3.4.2.1.5 Evidence of Microblasting1. Polished glass beads exposed in surface image2. Significant color/gray scale contrast between front and back component scans3.4.2.1.6 Evidence of

48、Chemical Etch1. Polished glass beads exposed in surface image2. Significant color/gray scale contrast between front and back component scans3. Signs of chemical reaction/indications of fluid ingression or gaps where leads enter package3.4.2.1.7 Evidence of Original Marking 1. Original paint markings

49、 seen through blacktop layer (see Appendix A, Figure A13)2. Partial etch marking (ghost image) left after removal by sanding (see Appendix A, Figure A3)3.4.2.1.8 Acoustic Impedance Measurement (AIM)NOTE: Can be performed on suspect counterfeit part itself, front versus back surface, or in comparison to known good part.1. AIM value compared to known authentic AIM of same component 2. AIM front surface value compared to back surface value

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1