SAE AS 6305-2017 DIMENSIONS AND GAGING MORTORQ SPIRAL DRIVE INTERNAL RECESS.pdf

1、AEROSPACE STANDARDDIMENSIONS AND GAGINGMORTORQ SPIRAL DRIVEINTERNAL RECESSAS6305Copyright 2017 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recordin

2、g, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2017-01THIRD ANGLE PROJECTIONCUSTODIAN: E-25FEDE

3、RAL SUPPLY CLASS5305AS6305SHEET 1 OF 6PROCUREMENT SPECIFICATION: NONESAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis entirely voluntary, and its applicability and suitability forany particula

4、ruse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written comments and suggestions.SAE values your input. To provi

5、de feedback on thisTechnical Report, please visit http:/standards.sae.org/AS6305RATIONALETHE STANDARD SETS FORTH THE DIMENSIONS AND GAGING SYSTEM FOR THE SPIRAL DRIVE (MORTORQ)SYSTEM AND IS SUPPLEMENTAL TO FASTENER STANDARDS DEVELOPED THAT INCORPORATE THIS DRIVE FEATURE.P RECESS PENETRATION PER PART

6、 STANDARDFIGURE 1 - RECESS CONFIGURATION ABP2322AEROSPACE STANDARD AS6305SHEET 2 OF 6DIMENSIONS AND GAGINGMORTORQ SPIRAL DRIVEINTERNAL RECESSFIGURE 2 - GO/NO GO GAGE CNO-GOELEMENT DGO ELEMENTNO-GO ELEMENTGO ELEMENTHANDLEFASTENER RECESSTO BE INSPECTEDCOLOR COATED REDFOR “NO GO” ELEMENTCOLOR COATED GR

7、EENFOR “GO” ELEMENTAEROSPACE STANDARD AS6305SHEET 3 OF 6DIMENSIONS AND GAGINGMORTORQ SPIRAL DRIVEINTERNAL RECESSFIGURE 3 PENETRATION GAGESTANDARD DIAL GAGEWITH NUMERALS READINGCOUNTER-CLOCKWISESET SCREWGAGE BODYGAGE PINFASTENER TOBE INSPECTEDAEROSPACE STANDARD AS6305SHEET 4 OF 6DIMENSIONS AND GAGING

8、MORTORQ SPIRAL DRIVEINTERNAL RECESSFIGURE 4 - GAGE PINTABLE 1 BASIC RECESS CONFIGURATION DIMENSIONSDRIVE SIZE A (MAX) B (NOM)000 .0750 .035500 .1230 .05850 .1724 .08211 .2425 .11412 .3100 .14603 .3557 .16764 .4305 .20305 .5083 .23996 .5958 .28117 .8023 .3787“F”L“M”HGE“K”AEROSPACE STANDARD AS6305SHEE

9、T 5 OF 6DIMENSIONS AND GAGINGMORTORQ SPIRAL DRIVEINTERNAL RECESSTABLE 2 GO/NO GO GAGE DIMENSIONSTABLE 3 PENETRATION GAGE PIN DIMENSIONSDRIVE SIZEEFREFG HKREFLMREF+0-.005+.0005-.0005+.015-.015+.0000-.0003000 .250 1.000 .0745 .110 .390 .0696 .06300 .250 1.000 .1200 .110 .390 .1160 .0630 .250 1.000 .16

10、90 .110 .390 .1650 .0631 .500 1.000 .2380 .115 .385 .2340 .0632 .500 1.000 .3060 .115 .385 .3000 .0633 .500 1.000 .3530 .200 .300 .3440 .0634 .500 1.000 .4280 .200 .300 .4170 .0635 .625 1.000 .5040 .200 .300 .4930 .0636 .650 1.000 .5890 .200 .300 .5780 .0637 .875 1.250 .8120 .200 .300 .7843 .063DRIV

11、E SIZEC NO-GO D GO+.0002/-0 +0/-.0002000 .0750 .070800 .1230 .11880 .1724 .16821 .2425 .23832 .3100 .30583 .3557 .35154 .4305 .42635 .5083 .50416 .5958 .59167 .8023 .7981AEROSPACE STANDARD AS6305SHEET 6 OF 6DIMENSIONS AND GAGINGMORTORQ SPIRAL DRIVEINTERNAL RECESSNOTESNOTICETHIS DOCUMENT REFERENCES A

12、 DESIGN WHICH IS COVERED BY UNITED STATES AND INTERNATIONAL PATENTS. THE PATENT OWNER HAS FILED A STATEMENT WITH SAE ASSURING THAT LICENSES FOR THE USE OF THE PATENT SHALL BE GRANTED UNDER REASONABLE AND NON-DISCRIMANATORY TERMS.1. THE WRENCHING ELEMENT DESIGNATION SHALL BE AS SHOWN IN THE FOLLOWING

13、 EXAMPLE:AS6305-XXXDRIVE SIZEDASH NO. PER TABLE 12. DIMENSIONS ARE IN INCHES.3. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.4. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THISDOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.