SAE AS 6315-2017 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD.pdf

1、 AEROSPACE STANDARD WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD AS6315Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyin

2、g, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2017-11THIRD ANGLE PROJECTION CUST

3、ODIAN: E-25 FEDERAL SUPPLY CLASS 5970 AS6315 SHEET 1 OF 8 PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report is entirely voluntary, and its applicability ands

4、uitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.

5、SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS6315 RATIONALE THIS DESIGN STANDARD SETS FORTH THE DIMENSIONS AND GAGING SYSTEM FOR THE EXTERNAL MORTORQ SUPER BOLT HEAD SPIRAL DRIVE SYSTEM AND IS SUPPLEMENTAL TO FASTENER STANDARDS DEVELOPED

6、 THAT INCORPORATE THIS DRIVE FEATURE. FIGURE 1 - WRENCHING CONFIGURATION AEROSPACE STANDARD AS6315 SHEET 2 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD FIGURE 2 - GO/NO GO GAGE GO RING GAGE: USING LIGHT FINGER PRESSURE ONLY, PLACE THE BOLT HEAD INTO THE GO GAGE UNTIL RESISTAN

7、CE IS FELT. FAILURE TO BOTTOM THE BOLT HEAD INTO THE GAGE SHALL BE CAUSE FOR REJECTION. NO-GO RING GAGE: USING LIGHT FINGER PRESSURE ONLY, PLACE TWO OPPOSING ROOTS OF THE BOLT HEAD INTO THE NO-GO GAGE UNTIL RESISTANCE IS FELT. ROTATE THE BOLT HEAD AND CHECK ALL THREE OPPOSING ROOTS FOR FIT. GAGE ENT

8、RY BEYOND THE ACCEPTABLE EXTERNAL FALLAWAY LIMIT AT THE HEAD SURFACE OF ANY OPPOSING ROOTS ORIENTATION IS CAUSE FOR REJECTION. AEROSPACE STANDARD AS6315 SHEET 3 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD FIGURE 3 - FALL AWAY GAGE FALLAWAY ROOT STEP GO-GAGE: USING LIGHT FING

9、ER PRESSURE ONLY, PLACE TWO OPPOSING ROOTS OF THE BOLT HEAD INTO THE FALLAWAY ROOT STEP GO-GAGE. ROTATE THE BOLT HEAD AND CHECK ALL THREE OPPOSING ROOTS FOR FIT. FAILURE TO BOTTOM THE BOLT HEAD IN THE GAGE IN ANY OPPOSING ROOTS ORIENTATION IS CAUSE FOR REJECTION. FAILURE OF THE BOLT HEAD TO EXTEND B

10、EYOND THE FIRST STEP (“K“ HEIGHT) OF THE GAGE IS ALSO CAUSE FOR REJECTION. FALLAWAY CYLINDRICAL GO-GAGE: USING LIGHT FINGER PRESSURE ONLY, PLACE THE BOLT HEAD INTO THE APPROPRIATE CYLINDRICAL GO-GAGE. FAILURE TO BOTTOM THE BOLT HEAD IN THIS GAGE IS CAUSE FOR REJECTION. FALLAWAY CYLINDRICAL STEP GAGE

11、: USING LIGHT FINGER PRESSURE ONLY, PLACE THE BOLT HEAD THROUGH THE BOTTOM OF THE FALLAWAY CYLINDRICAL STEP GAGE. THE TOP OF THE BOLT HEAD EXTENDING BEYOND THE TOP SURFACE OF THE GAGE IS CAUSE FOR REJECTION. AEROSPACE STANDARD AS6315 SHEET 4 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL

12、 BOLT HEAD TABLE 1 - BASIC WRENCHING CONFIGURATION DIMENSIONS AS6315 DASH NO. DRIVE SIZE A B E RAD REF F RAD REF 01 MTS-X1 .0910 .0890 .0700 .0680 .0031 .0035 02 MTS-X2 .1190 .1170 .0915 .0895 .0041 .0045 04 MTS-X4 .1470 .1440 .1131 .1101 .0051 .0056 05 MTS-X5 .1820 .1790 .1400 .1370 .0063 .0069 06

13、MTS-X6 .2200 .2160 .1692 .1652 .0076 .0084 07 MTS-X7 .2380 .2340 .1831 .1791 .0082 .0091 08 MTS-X8 .2890 .2850 .2223 .2183 .0099 .0110 10 MTS-X10 .3640 .3600 .2800 .2760 .0124 .0139 11 MTS-X11 .3900 .3860 .3000 .2960 .0134 .0149 12 MTS-X12 .4260 .4220 .3277 .3237 .0147 .0200 14 MTS-X14 .5010 .4970 .

14、3854 .3814 .0172 .0191 16 MTS-X16 .5730 .5690 .4408 .4368 .0197 .0218 18 MTS-X18 .6480 .6420 .4985 .4925 .0223 .0247 20 MTS-X20 .7180 .7120 .5523 .5463 .0247 .0274 22 MTS-X22 .7900 .7840 .6077 .6017 .0272 .0301 24 MTS-X24 .8630 .8570 .6639 .6579 .0297 .0329 26 MTS-X26 .9320 .9260 .7169 .7109 .0321 .

15、0355 28 MTS-X28 1.0030 .9970 .7716 .7656 .0345 .0382 29 MTS-X29 1.0236 1.0176 .7874 .7814 .0352 .0390 30 MTS-X30 1.0710 1.0650 .8239 .8179 .0369 .0408 32 MTS-X32 1.1410 1.1350 .8777 .8717 .0393 .0435 34 MTS-X34 1.2100 1.2040 .9308 .9248 .0416 .0461 36 MTS-X36 1.2830 1.2770 .9869 .9809 .0442 .0489 38

16、 MTS-X38 1.3560 1.3500 1.0431 1.0371 .0467 .0517 40 MTS-X40 1.4230 1.4170 1.0946 1.0886 .0490 .0542 42 MTS-X42 1.4950 1.4890 1.1500 1.1440 .0515 .0570 44 MTS-X44 1.5650 1.5590 1.2039 1.1979 .0539 .0596 AEROSPACE STANDARD AS6315 SHEET 5 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT

17、HEAD TABLE 2 - GO/NO GO GAGE DIMENSIONS DRIVE SIZE +.0003 -.0000 R +.0003 -.0000 S +.0000 -.0003 C +.000 -.005 T .015 P .015 G REF H REF J +.005 -.000 I.D. K REF L +.010 -.000 M +.030 -.000 N MTS-X1 .0911 .0701 .0680 .500 1.000 2.000 .500 .875 .505 .563 .100 .300 MTS-X2 .1191 .0916 .0895 .500 1.000

18、2.000 .500 .875 .505 .563 .131 .300 MTS-X4 .1471 .1132 .1101 .500 1.000 2.000 .500 .875 .505 .563 .162 .300 MTS-X5 .1821 .1401 .1370 .500 1.000 2.000 .500 .875 .505 .563 .200 .300 MTS-X6 .2201 .1693 .1652 .500 1.000 2.000 .500 .875 .505 .563 .242 .300 MTS-X7 .2381 .1832 .1791 .500 1.000 2.000 .500 .

19、875 .505 .563 .262 .300 MTS-X8 .2891 .2224 .2183 .500 1.000 2.000 .500 .875 .505 .563 .318 .300 MTS-X10 .3641 .2801 .2760 .750 1.125 2.000 .563 .875 .755 .563 .401 .550 MTS-X11 .3901 .3001 .2960 .750 1.125 2.000 .563 .875 .755 .563 .429 .550 MTS-X12 .4261 .3278 .3237 .750 1.125 2.000 .563 .875 .755

20、.563 .476 .550 MTS-X14 .5011 .3855 .3814 .750 1.125 2.000 .563 .875 .755 .563 .551 .550 MTS-X16 .5731 .4409 .4368 1.000 2.000 3.500 1.000 1.750 1.005 .875 .630 .750 MTS-X18 .6481 .4986 .4925 1.000 2.000 3.500 1.000 1.750 1.005 .875 .713 .750 MTS-X20 .7181 .5524 .5463 1.000 2.000 3.500 1.000 1.750 1.

21、005 .875 .790 .750 MTS-X22 .7901 .6078 .6017 1.250 2.000 3.500 1.000 1.750 1.255 .875 .869 1.000 MTS-X24 .8631 .6640 .6579 1.250 2.000 3.500 1.000 1.750 1.255 .875 .949 1.000 MTS-X26 .9321 .7170 .7109 1.250 2.000 3.500 1.000 1.750 1.255 .875 1.025 1.000 MTS-X28 1.0031 .7717 .7656 1.500 2.000 3.500 1

22、.000 1.750 1.505 .875 1.103 1.100 MTS-X29 1.0237 .7875 .7814 1.500 2.000 3.500 1.000 1.750 1.505 .875 1.125 1.100 MTS-X30 1.0711 .8240 .8179 1.500 2.000 3.500 1.000 1.750 1.505 .875 1.178 1.100 MTS-X32 1.1411 .8778 .8717 1.500 2.000 3.500 1.000 1.750 1.505 .875 1.255 1.200 MTS-X34 1.2101 .9309 .9248

23、 1.500 2.000 3.500 1.000 1.750 1.505 .875 1.331 1.250 MTS-X36 1.2831 .9870 .9809 2.000 3.000 5.000 1.500 2.500 2.005 1.250 1.411 1.400 MTS-X38 1.3561 1.0432 1.0371 2.000 3.000 5.000 1.500 2.500 2.005 1.250 1.492 1.400 MTS-X40 1.4231 1.0947 1.0886 2.000 3.000 5.000 1.500 2.500 2.005 1.250 1.565 1.500

24、 MTS-X42 1.4951 1.1501 1.1440 2.000 3.000 5.00 1.500 2.500 2.005 1.250 1.645 1.500 MTS-X44 1.5651 1.2040 1.1979 2.000 3.000 5.000 1.500 2.500 2.005 1.250 1.722 1.600 AEROSPACE STANDARD AS6315 SHEET 6 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD TABLE 3 - FALLAWAY GAGE DIMENSI

25、ONS TABLE 3A - FALLAWAY GAGE DIMENSIONS A-H DRIVE SIZE A +.0004 -.0000 A2 +.0004 -.0000 B +.0005 -.0000 C +.010 -.000 E +.010 -.010 F +.010 -.010 G +.010 -.010 H +.015 -.015 MTS-X1 .0920 .0846 .0710 .093 .175 .750 .250 .125 MTS-X2 .1200 .1107 .0925 .093 .195 .935 .312 .125 MTS-X4 .1480 .1367 .1141 .

26、093 .225 1.125 .375 .125 MTS-X5 .1830 .1693 .1410 .109 .275 1.220 .400 .125 MTS-X6 .2210 .2046 .1702 .156 .365 1.165 .437 .125 MTS-X7 .2390 .2213 .1841 .171 .375 1.240 .500 .250 MTS-X8 .2900 .2688 .2233 .187 .455 1.400 .562 .250 MTS-X10 .3650 .3385 .2810 .250 .620 1.615 .718 .250 MTS-X11 .3910 .3627

27、 .3010 .265 .650 1.750 .750 .250 MTS-X12 .4270 .3962 .3287 .281 .680 1.915 .860 .250 MTS-X14 .5020 .4659 .3864 .312 .760 2.180 1.000 .375 MTS-X16 .5740 .5329 .4418 .345 .855 2.425 1.125 .375 MTS-X18 .6490 .6026 .4995 .375 .950 2.600 1.190 .375 MTS-X20 .7190 .6677 .5533 .435 1.065 2.745 1.250 .375 MT

28、S-X22 .7910 .7347 .6087 .500 1.135 2.830 1.250 .375 MTS-X24 .8640 .8026 .6649 .560 1.340 3.000 1.375 .375 MTS-X26 .9330 .8668 .7179 .560 1.385 3.105 1.390 .500 MTS-X28 1.0040 .9328 .7726 .625 1.525 3.300 1.438 .500 MTS-X29 1.0246 .9519 .7884 .630 1.555 3.340 1.500 .500 MTS-X30 1.0720 .9960 .8249 .63

29、5 1.580 3.380 1.535 .500 MTS-X32 1.1420 1.0611 .8787 .685 1.675 3.525 1.550 .500 MTS-X34 1.2110 1.1253 .9318 .710 1.775 3.640 1.680 .750 MTS-X36 1.2840 1.1932 .9879 .750 1.860 3.750 1.565 .750 MTS-X38 1.3570 1.2611 1.0441 .785 1.975 3.900 1.825 .750 MTS-X40 1.4240 1.3234 1.0956 .875 2.100 3.980 1.62

30、5 .750 MTS-X42 1.4960 1.3904 1.1510 .875 2.165 4.145 1.960 .750 MTS-X44 1.5660 1.4555 1.2049 .875 2.225 4.210 1.750 .750 AEROSPACE STANDARD AS6315 SHEET 7 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD TABLE 3B - FALLAWAY GAGE DIMENSIONS J-W DRIVE SIZE J +.010 .000 K +.005 -.00

31、0 L +.015 -.015 M +.015 -.015 R RAD +.000 -.001 T +.000 -.001 W +.015 -.015 MTS-X1 .420 .021 1.225 .070 .005 .018 .750 MTS-X2 .430 .027 1.445 .070 .007 .024 .750 MTS-X4 .470 .034 1.675 .070 .008 .029 .750 MTS-X5 .470 .042 1.835 .070 .010 .036 .750 MTS-X6 .480 .051 1.890 .100 .012 .044 .750 MTS-X7 .4

32、90 .055 1.985 .100 .013 .048 .750 MTS-X8 .635 .066 2.250 .120 .015 .058 1.000 MTS-X10 .675 .084 2.665 .155 .019 .073 1.000 MTS-X11 .750 .090 2.980 .165 .020 .078 1.125 MTS-X12 .800 .100 3.190 .l80 .022 .087 1.125 MTS-X14 .985 .115 3.570 .205 .026 .100 1.500 MTS-X16 1.140 .132 3.940 .220 .030 .115 1.

33、750 MTS-X18 1.300 .149 4.250 .240 .033 .130 2.000 MTS-X20 1.400 .165 4.550 .290 .037 .144 2.125 MTS-X22 1.490 .182 4.740 .370 .040 .158 2.250 MTS-X24 1.530 .198 5.160 .375 .045 .173 2.250 MTS-X26 1.570 .214 5.390 .375 .049 .186 2.500 MTS-X28 1.720 .231 5.830 .410 .052 .201 2.500 MTS-X29 1.725 .235 5

34、.875 .420 .054 .205 2.500 MTS-X30 1.730 .246 5.910 .430 .055 .214 2.500 MTS-X32 1.900 .262 6.270 .460 .060 .228 2.750 MTS-X34 1.950 .278 6.420 .465 .062 .242 3.000 MTS-X36 2.090 .295 6.750 .500 .066 .257 3.000 MTS-X38 2.150 .312 6.925 .545 .069 .271 3.250 MTS-X40 2.280 .327 7.540 .600 .073 .285 3.25

35、0 MTS-X42 2.300 .344 7.390 .600 .077 .299 3.250 MTS-X44 2.350 .360 7.970 .565 .082 .313 3.250 AEROSPACE STANDARD AS6315 SHEET 8 OF 8 WRENCHING CONFIGURATION EXTERNAL MORTORQ SUPER SPIRAL BOLT HEAD NOTES: NOTICE THIS DOCUMENT REFERENCES A DESIGN WHICH IS COVERED BY UNITED STATES AND INTERNATIONAL PAT

36、ENTS. THE PATENT OWNER HAS FILED A STATEMENT WITH SAE ASSURING THAT LICENSES FOR THE USE OF THE PATENT SHALL BE GRANTED UNDER REASONABLE AND NON-DISCRIMATORY TERMS. 1. THE WRENCHING ELEMENT DESIGNATION SHALL BE AS SHOWN IN THE FOLLOWING EXAMPLE: AS6315-XX WRENCHING ELEMENT DASH NO. PER TABLE 1 2. DI

37、MENSIONS ARE IN INCHES. 3. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. THIS REPORT IS PUBLISHED BY SAE TO ADVANCE THE STATE OF TECHNICAL AND ENGINEERING SCIENCES. THE USE OF THIS TECHNICAL REPORT IS ENTIRELY VOLUNTARY, AND ITS APPLICABILITY AND SUITABILITY FOR ANY PARTICULAR USE, INCLUDING ANY PATENT INFRINGEMENT ARISING THEREFROM, IS THE SOLE RESPONSIBILITY OF THE USER.