SAE AS 6323-2015 FITTING ASSEMBLY EXTENDED UNION AXIALLY SWAGED HYDRAULIC UP TO 1500 PSI.pdf

1、 AEROSPACE STANDARD FITTING ASSEMBLY, EXTENDED UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI AS6323 Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical

2、, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2015-02THIRD ANGLE PR

3、OJECTION CUSTODIAN: G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS6323 SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS6116 /4/ SAE Technical 6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLQHHULQJVFLHQFes. The useof this report is entirely voluntary, and its applicability

4、 andsuitability for any particularuse, includingany patenWLQIULQJHPHQWDULVLQJWKHUHIURPLVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. SAE va

5、lues your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS6323 RATIONALE NEW STANDARD FOR OPERATING PRESSURES UP TO AND INCLUDING 1500 PSI. FIGURE 1 FITTING ASSEMBLY, EXTENDED UNION AEROSPACE STANDARD AS6323 SHEET 2 OF 3 FITTING ASSEMBLY, EXT

6、ENDED UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI TABLE 1A - DIMENSIONS A THROUGH J BASIC NO. AS6323 /15/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 A MAX A1 MAX A MAX A1 MAX C MAX E MAX EA MAX F MIN FA MIN J /12/ ALLOWABLE TUBE GAP STANDARD LENGTH /16/ J /12/ ALLOWABLE TUBE GAP

7、EXTENDED LENGTH /16/ STANDARD LENGTH /16/ EXTENDED LENGTH /16/ 0404 .250 .250 2.156 1.830 3.536 3.210 .406 .435 .435 .253 .253 0 1.000 0 2.380 0505 .3125 .3125 2.416 2.106 4.066 3.756 .471 .503 .503 .3155 .3155 0 1.000 0 2.650 0606 .375 .375 2.714 2.244 4.504 4.034 .563 .580 .580 .378 .378 0 1.000 0

8、 2.790 0808 .500 .500 3.120 2.592 5.250 4.722 .695 .755 .755 .503 .503 0 1.000 0 3.130 1010 .625 .625 3.130 2.626 5.310 4.806 .857 .929 .929 .629 .629 0 1.000 0 3.180 1212 .750 .750 3.410 2.830 5.790 5.210 1.002 1.150 1.150 .754 .754 0 1.000 0 3.380 1616 1.000 1.000 4.150 3.378 7.525 6.753 1.324 1.4

9、74 1.474 1.004 1.004 0 1.000 0 4.375 2020 1.250 1.250 4.700 3.836 8.540 7.676 1.588 1.768 1.768 1.255 1.255 0 1.000 0 4.840 2424 1.500 1.500 5.420 4.404 9.820 8.804 1.832 2.070 2.070 1.505 1.505 0 1.000 0 5.400 TABLE 1B - DIMENSIONS W THROUGH W4A AND WEIGHTS BASIC NO. AS6323 /15/ SIZE CODE NOMINAL T

10、UBE SIZE END 1 NOMINAL TUBE SIZE END 2 W MIN WA MIN W1 MAX W1A MAX W2 .002 W2A .002 RW3 MAX RW3A MAX RW4 MAX RW4A MAX WEIGHT APPROX LB/EA STANDARD LENGTH WEIGHT APPROX LB/EA EXTENDED LENGTH 0404 .250 .250 .185 .185 .604 .604 .320 .320 .020 .020 .020 .020 .015 .025 0505 .3125 .3125 .180 .180 .724 .72

11、4 .371 .371 .020 .020 .020 .020 .020 .035 0606 .375 .375 .195 .195 .883 .883 .463 .463 .020 .020 .020 .020 .030 .050 0808 .500 .500 .210 .210 1.076 1.076 .595 .595 .020 .020 .020 .020 .055 .085 1010 .625 .625 .225 .225 1.076 1.076 .758 .758 .020 .020 .020 .020 .080 .130 1212 .750 .750 .235 .235 1.20

12、1 1.201 .903 .903 .025 .025 .025 .025 .130 .205 1616 1.000 1.000 .260 .260 1.566 1.566 1.196 1.196 .035 .035 .035 .035 .255 .440 2020 1.250 1.250 .285 .285 1.829 1.829 1.460 1.460 .035 .035 .035 .035 .395 .665 2424 1.500 1.500 .310 .310 2.178 2.178 1.704 1.704 .035 .035 .035 .035 .595 .950 NOTES: /1

13、/ MATERIALS: CODE LETTER “D“ BODY - TYPE 6061-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/8 OR AMS4117. RING - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. 2. FINISH: BODY - CHEMICAL CONVERSION COATED PER MIL-DTL-5541 TYPE I CLASS 3. RINGS - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYED GREEN, S

14、IMILAR TO NO. 14187, 14193, OR 14223 OF FED-STD-595 AND SHALL BE DUPLEX SEALED. /3/ COATINGS/LUBRICANTS: BODY a. DRY FILM LUBRICANT PER AS5272 TYPE I SHALL BE APPLIED TO THE OD OF THE AXIALLY SWAGED FITTING END. ADDITIONAL LUBRICANT APPLIED SHALL BE SPECIFIED BY MANUFACTURER. THE LUBRICANTS SHALL NO

15、T BE IN CONTACT WITH THE SYSTEM FLUID. b. POLYTETRAFLUOROETHYLENE (PTFE) COAT, LIGHT GREEN, SHALL BE APPLIED TO PORTIONS OF ID (BORE) UP TO THE FIRST GROOVE. OVERSPRAY IN GROOVE IS NOT PERMITTED. c. A MINIMUM OF TWO GROOVES (END SIZE -05 AND LARGER) SHALL BE FILLED WITH ELASTOMERIC DIMETHYL SILOXANE

16、 COMPOUND. FOR SMALLER SIZE ENDS, A MINIMUM OF ONE GROOVE SHALL BE FILLED WITH THE COMPOUND. AEROSPACE STANDARD AS6323 SHEET 3 OF 3 FITTING ASSEMBLY, EXTENDED UNION, AXIALLY SWAGED, HYDRAULIC, UP TO 1500 PSI /4/ PROCUREMENT SPECIFICATION: AS6116 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED

17、 TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS6116 FOR THIS STANDARD. SEE www.eAuditN FOR THE CURRENT QPL ON-LINE. 5. DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE

18、SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/ IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS6116 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN. FOR SIZE -05 AND LARGER, THE RING O.D. SHALL HAVE TWO

19、 GROOVES INDICATING DUAL SEALING BACK UP FEATURE. 7. FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS6124. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. 9. BREAK ALL EDGES .003 TO .01

20、0 INCHES UNLESS OTHERWISE SPECIFIED. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 11. DIMENSIONS IN INCHES UNLESS OTHERWISE SPECIFIED. TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 0q 30. /12/ ,0(16,21-,S THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /13/ ,0(16,21$ IS

21、THE FITTING ASSEMBLY LENGTH PRIOR TO SWAGE AN$,67+($)7(5 SWAGE ASSEMBLY LENGTH MEASURED FROM THE SWAGED RINGS. /14/ PARTS FOR OXYGEN SYSTEMS SHALL BE IDENTIFIED IN THE PART NUM%(5$668),;&2($16+$/%()851 ISHED CLEANED, PACKAGED, AND LABELED IN ACCORDANCE WITH ARP1176-1-50. /15/ EXAMPLE OF PART NUMBER:

22、 /16/ THIS PART IS INTENDED AS A REPAIR FITTING. STANDARD LENGTH FITTINGS MAY BE USED TO REPAIR TUBING WITH UP TO ONE INCH OF DAMAGE. EXTENDED LENGTH FITTINGS MAY BE USED TO REPAIR A CUTOU7$681,21 17. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER

23、IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.