SAE AS 6458A-2015 FITTING ASSEMBLY TEE AXIALLY SWAGED TO FEMALE FLARELESS ON THE RUN FEMALE FLARELESS ON THE SIDE HYDRAULIC UP TO 1500 PSI.pdf

1、 AEROSPACE STANDARD FITTING ASSEMBLY, TEE, AXIALLY SWAGED TO FEMALEFLARELESS ON THE RUN, FEMALE FLARELESS ON THESIDE, HYDRAULIC, UP TO 1500 PSI AS6458Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in a

2、ny form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS

3、: http:/www.sae.org ISSUED 2011-07REVISED 2015-06THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730AS6458 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: /4/ AS6116SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technical

4、andengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevise

5、d,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6458A RATIONALE ADDED STANDARD CONFIGURATION 242424. FIGURE 1 - TEE, AXIALLY SWAGED TO FEMAL

6、E FLARELESS ON THE RUN, FEMALE FLARELESS ON THE SIDE AEROSPACE STANDARD AS6458 SHEET 2 OF 4 REV. A FITTING ASSEMBLY, TEE, AXIALLY SWAGED TO FEMALE FLARELESS ON THE RUN, FEMALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI TABLE 1A - DIMENSIONS A THROUGH F BASIC NO. AS6458 /16/ SIZE CODE NOMINAL T

7、UBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 A .015 B MAX B1 MAX C .015 E MAX F MIN 040404 .250 .250 .250 .874 1.112 .959 .874 .435 .253 050505 .3125 .3125 .3125 .949 1.258 1.110 .949 .503 .3155 060606 .375 .375 .375 1.047 1.464 1.237 1.047 .580 .378 080808 .500 .500 .500 1.230 1.7

8、65 1.505 1.230 .755 .503 101010 .625 .625 .625 1.434 1.843 1.603 1.434 .929 .629 121212 .750 .750 .750 1.598 2.103 1.823 1.598 1.150 .754 161612 1.000 1.000 .750 1.864 2.618 2.238 1.760 1.474 1.004 161616 1.000 1.000 1.000 1.864 2.618 2.238 1.864 1.474 1.004 202020 1.250 1.250 1.250 2.093 3.069 2.65

9、4 2.093 1.768 1.255 242424 1.500 1.500 1.500 2.437 3.600 3.105 2.437 2.070 1.505 TABLE 1B - DIMENSIONS G THROUGH J BASIC NO. AS6458 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 G .015 ( H ) ( H1 ) J /13/ TUBE DEDUCTION 040404 .250 .250 .250 .438 .562 .562 .4

10、19 +.150/-.180 050505 .3125 .3125 .3125 .465 .625 .625 .435 +.150/-.180 060606 .375 .375 .375 .563 .688 .688 .492 +.150/-.195 080808 .500 .500 .500 .750 .875 .875 .590 +.150/-.210 101010 .625 .625 .625 .875 1.000 1.000 .663 +.150/-.200 121212 .750 .750 .750 1.063 1.250 1.250 .783 +.150/-.245 161612

11、1.000 1.000 .750 1.304 1.500 1.250 .928 +.150/-.330 161616 1.000 1.000 1.000 1.304 1.500 1.500 .928 +.150/-.330 202020 1.250 1.250 1.250 1.618 1.812 1.812 1.104 +.150/-.375 242424 1.500 1.500 1.500 1.806 2.125 2.125 1.275 +.150/-.425 TABLE 1C - DIMENSIONS K THROUGH T1 BASIC NO. AS6458 /16/ SIZE CODE

12、 NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZEEND 3 K MAXK1 MAXN GAGEN1 GAGE( T ) THREAD PER AS8879 ( T1 ) THREAD PER AS8879 040404 .250 .250 .250 .248 .248 .2930 .2930 .4375-20 UNJF-3B .4375-20 UNJF-3B050505 .3125 .3125 .3125 .331 .331 .3500 .3500 .5000-20 UNJF-3B .5000-20 UNJF-

13、3B060606 .375 .375 .375 .302 .302 .4120 .4120 .5625-18 UNJF-3B .5625-18 UNJF-3B080808 .500 .500 .500 .316 .316 .5600 .5600 .7500-16 UNJF-3B .7500-16 UNJF-3B101010 .625 .625 .625 .424 .424 .6730 .6730 .8750-14 UNJF-3B .8750-14 UNJF-3B121212 .750 .750 .750 .388 .388 .8100 .8100 1.0625-12 UNJ-3B 1.0625

14、-12 UNJ-3B 161612 1.000 1.000 .750 .454 .388 1.0620 .8100 1.3125-12 UNJ-3B 1.0625-12 UNJ-3B 161616 1.000 1.000 1.000 .454 .454 1.0620 1.0620 1.3125-12 UNJ-3B 1.3125-12 UNJ-3B 202020 1.250 1.250 1.250 .465 .465 1.3160 1.3160 1.6250-12 UNJ-3B 1.6250-12 UNJ-3B 242424 1.500 1.500 1.500 .460 .460 1.5650

15、1.5650 1.8750-12 UNJ-3B 1.8750-12 UNJ-3B TABLE 1D - DIMENSIONS W THROUGH W4 AND WEIGHTS BASIC NO. AS6458 /16/ SIZE CODE NOMINAL TUBE SIZE END 1 NOMINAL TUBE SIZE END 2 NOMINAL TUBE SIZE END 3 W MIN W1 MAX W2 .002 W3 MAX W4 MAX WEIGHT APPROX LB/EA 040404 .250 .250 .250 .185 .604 .320 .020 .020 .040 0

16、50505 .3125 .3125 .3125 .180 .724 .371 .020 .020 .050 060606 .375 .375 .375 .195 .883 .463 .020 .020 .060 080808 .500 .500 .500 .210 1.076 .595 .020 .020 .115 101010 .625 .625 .625 .225 1.076 .758 .020 .020 .175 121212 .750 .750 .750 .235 1.201 .903 .025 .025 .290 161612 1.000 1.000 .750 .260 1.566

17、1.196 .035 .035 .430 161616 1.000 1.000 1.000 .260 1.566 1.196 .035 .035 .450 202020 1.250 1.250 1.250 .285 1.829 1.460 .035 .035 .755 242424 1.500 1.500 1.500 .310 2.178 1.704 .035 .035 1.090 AEROSPACE STANDARD AS6458 SHEET 3 OF 4 REV. A FITTING ASSEMBLY, TEE, AXIALLY SWAGED TO FEMALE FLARELESS ON

18、THE RUN, FEMALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI NOTES: /1/ MATERIALS: CODE LETTER “D“ BODY - TYPE 6061-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/8. RING - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. NUT - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. WIRE - TYPE 302 OR

19、305, CONDITION A CORROSION RESISTANT STEEL WIRE PER ASTM A580 (SIZES -04 AND 05). - TYPE 2024-T4 OR 2024-T351 ALUMINUM ALLOY WIRE PER AMS-QQ-A-225/6 (SIZES -06 AND LARGER). 2. FINISH: BODY - CHEMICAL CONVERSION COAT PER MIL-DTL-5541 TYPE I CLASS 3. RING - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DY

20、ED GREEN, SIMILAR TO NO. 14187, 14193, OR 14223 OF FED-STD-595 AND SHALL BE DUPLEX SEALED. NUT - ANODIZE PER MIL-A-8625 TYPE II, CLASS 2, DYED BROWN SIMILAR TO NO. 10080, OF FED-STD-595 AND SHALL BE DUPLEX SEALED. WIRE - PASSIVATION PER AMS2700 (SIZES -04 AND -05). - ANODIZE PER MIL-A-8625 TYPE II,

21、CLASS 2, DYED YELLOW, WITH DUPLEX SEAL (SIZES -06 AND LARGER). /3/ COATINGS/LUBRICANTS: BODY a. DRY FILM LUBRICANT PER AS5272 TYPE I SHALL BE APPLIED TO THE OD OF THE AXIALLY SWAGED FITTING END. ADDITIONAL LUBRICANT APPLIED SHALL BE SPECIFIED BY MANUFACTURER. THE LUBRICANTS SHALL NOT BE IN CONTACT W

22、ITH THE SYSTEM FLUID. b. POLYTETRAFLUOROETHYLENE (PTFE) COAT, LIGHT GREEN, SHALL BE APPLIED TO PORTIONS OF ID (BORE) UP TO THE FIRST GROOVE. OVERSPRAY IN GROOVE IS NOT PERMITTED. c. A MINIMUM OF TWO GROOVES (END SIZE -05 AND LARGER) SHALL BE FILLED WITH ELASTOMERIC DIMETHYL SILOXANE COMPOUND. FOR SM

23、ALLER SIZE ENDS, A MINIMUM OF ONE GROOVE SHALL BE FILLED WITH THE COMPOUND. WIRE - SOLID FILM LUBRICANT PER AS5272, TYPE I. /4/ PROCUREMENT SPECIFICATION: AS6116 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN

24、 THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS6116 FOR THIS STANDARD. SEE www.eAuditN FOR THE CURRENT QPL ON-LINE. 5. DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENS

25、URE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION. /6/ IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS6116 AND SHALL BE IDENTIFIED ON THE RING IN THE AREA SHOWN. FOR SIZE -05 AND LARGER, THE RING OD SHALL HAVE TWO GROOVES INDICATING DUAL SEALING BACK UP FEATURE. 7. FITTINGS SHALL BE INSTALLED IN ACCOR

26、DANCE WITH AS6124. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, THE MAXIMUM MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. 9. BREAK ALL EDGES .003 TO .010 INCHES UNLESS OTHERWISE SPECIFIED. 10. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.

27、11. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .015, ANGULAR DIMENSIONS 030. AEROSPACE STANDARD AS6458 SHEET 4 OF 4 REV. A FITTING ASSEMBLY, TEE, AXIALLY SWAGED TO FEMALE FLARELESS ON THE RUN, FEMALE FLARELESS ON THE SIDE, HYDRAULIC, UP TO 1500 PSI /12/ FITTINGS

28、SHALL MATE WITH AS5863-(SIZE) OR AS5864-(SIZE). STANDARD COUPLING NUT SHALL BE DIMENSIONALLY AND FUNCTIONALLY EQUIVALENT TO AS4370DXXXX. /13/ DIMENSION “J” IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN. /14/ DIMENSION “B” IS THE FITTING ASSEMBLY LENGTH PRIOR TO SWAGE AND “B1” IS THE

29、 AFTER SWAGE ASSEMBLY LENGTH MEASURED FROM THE SWAGED RING. /15/ PARTS FOR OXYGEN SYSTEMS SHALL BE IDENTIFIED IN THE PART NUMBER AS SUFFIX CODE “A” AND SHALL BE FURNISHED CLEANED, PACKAGED, AND LABELED IN ACCORDANCE WITH ARP1176 CATEGORY 1A. /16/ EXAMPLE OF PART NUMBER: AS6458 D 12 12 12 A OPTIONAL

30、OXYGEN CLEANING /15/ BASIC PART NUMBER END 3 - SIZE CODE IN .062 INCH INCREMENTS(12 = .750 INCH) MATERIAL CODE LETTER /1/ END 2 - SIZE CODE IN .062 INCH INCREMENTS (12 = .750 INCH) END 1 - SIZE CODE IN .062 INCH INCREMENTS (12 = .750 INCH) 17. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE C

31、ONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.