SAE AS 7106 1-1995 National Aerospace and Defense Contractors Accreditation Program Requirements for the Control of Deliverable Production Software《国家航空航天和国防部承包商认可计划(NADCAP) 可交付使用的.pdf

1、The Engineering Society For Advancing Mobility Land Sea Air and SpaceI N T E R N A T I O N A L400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACESTANDARDCopyright 1995 Society of Automotive Engineers, Inc.All rights reserved.Printed in U.S.ASAE Technical Standards Board Rules provide that: “T

2、his report is published by SAE to advance the state of technical andengineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use ,including any patent infringement arising therefrom, is the sole responsibility of the user.”SAE revie

3、ws each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invit esyour written comments and suggestions.Submitted for recognition as an American National StandardIssued1995-03AS7106/1NATIONAL AEROSPACE AND DEFENSECONTRACTORS ACCREDITATION PROGR

4、AMREQUIREMENTS FOR THE CONTROL OF DELIVERABLE PRODUCTION SOFTWARE1. SCOPE1.1 This Aerospace Standard (AS) is to be used as a supplement to either SAE AS7106 or SAE AS7107 for suppliers who have software (to include firmware) that comprises all or part of a product that will be delivered to the custo

5、mer. This type of software is defined as Class I software in the core documents. All suppliers seeking NADCAP General Quality Systems accreditation who have Class I software shall conform to the requirements of this Standard.2. APPLICABLE DOCUMENTSThe following publications form a part of this speci

6、fication to the extent specified herein. The latest issue of SAE and PRI publications shall apply.2.1 SAE Publications:Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15086-0001.AS7106 National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Quality Program Requirements

7、AS7107 National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Inspection Systems RequirementsCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-SAEAS7106/1- 2 -2.2 PRI Publications:Av

8、ailable from Performance Review Institute, 163 Thornhill Road, Warrendale, PA 15086-7527.AC7106 National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Quality Program Audit CriteriaAC7107 National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Inspection Syst

9、em Audit Criteria3. REQUIREMENTS3.1 The software item shall be prepared with computer programs retrieved from a Software Configuration Management (SCM) controlled library.3.2 Procedures shall be documented to retrieve, build, verify, and install software.3.3 There shall be procedures for verifying t

10、hat the software designated for production matches the software released from the SCM library.3.4 There shall be procedures for handling and storing media used to prepare production software items.3.5 Software records shall be maintained. Software backups shall be securely stored in a remote locatio

11、n for disaster recovery in accordance with customer(s) data retention requirements. Storage and retention requirements shall be documented.3.6 There shall be procedures for verifying the transfer of software from memory devices into the production end item.3.7 There shall be procedures to detect cor

12、ruption of software during installation.3.8 Records shall be maintained for each software installation that is performed.3.9 Procedures shall be in place for part numbering and identification of software configurations for the production end item.3.10 All production versions of the software shall be

13、 uniquely identified.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-SAE AS7106/1- 3 -3.11 There shall be procedures in place to identify pre-programmed memory devices within a production end item, indicating its programmed status.3.12 The softwares product service history shall be maintained to provide assessments of software errors.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-