SAE AS 7514-2017 SLEEVE THREADLESS - FLEXIBLE FIXED CAVITY CURRENT CARRYING SELF BONDING.pdf

1、 AEROSPACE STANDARD SLEEVE, THREADLESS - FLEXIBLE, FIXED CAVITY, CURRENT CARRYING, SELF BONDING AS7514Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,

2、 photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2017-09THIRD ANGLE PRO

3、JECTION CUSTODIAN: G-3/G-3A FEDERAL SUPPLY CLASS 4730 AS7514 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS7510 /4/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report is entirely voluntary, and

4、its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comm

5、ents and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS7514 RATIONALE NEW PART STANDARD AS PART OF AS7510 TO SUPERSEDE AS5834. FIGURE 1 - SLEEVE TABLE 1 - DIMENSIONS AND WEIGHTS /6/ BASIC NO AS7514 /13/ SIZE CODE NOM TUBE SIZE

6、 REF A .002 B .005 C .002 D .002 LB/EA NOM REF ALUM 08 .500 .703 .627 .775 .755 .004 10 .625 .828 .627 .900 .880 .005 12 .750 1.009 .731 1.081 1.061 .007 16 1.000 1.290 .811 1.362 1.342 .010 20 1.250 1.537 .811 1.609 1.589 .011 24 1.500 1.807 .811 1.879 1.859 .013 28 1.750 2.059 .811 2.131 2.111 .01

7、5 32 2.000 2.332 .855 2.404 2.384 .018 36 2.250 2.582 .855 2.654 2.634 .020 40 2.500 2.832 .855 2.908 2.888 .024 48 3.000 3.332 .855 3.412 3.392 .030 56 3.500 3.848 .945 3.934 3.914 .042 64 4.000 4.354 .975 4.446 4.426 .053 AEROSPACE STANDARD AS7514 SHEET 2 OF 2 SLEEVE, THREADLESS - FLEXIBLE, FIXED

8、CAVITY, CURRENT CARRYING, SELF BONDING NOTES /1/ MATERIAL: MATERIAL CODE LETTER A TYPE 2024-T351, T851, T8510, OR T8511 ALUMINUM ALLOY PER AMS-QQ-A-225/6, AMS4120, AMS4339, AMS-QQ-A-200/3, AMS-WW-T-700/3, OR ASTM B211. 2. HEAT TREATMENT: MATERIAL CODE LETTER A IF THE RAW MATERIAL IS PROCURED IN THE

9、SOLUTION TREATED CONDITION, AGE TO T851 OR T8511 PER AMS2770 OR AMS2772. /3/ FINISH: MATERIAL CODE LETTER A ANODIZE PER AMS2472, OR MIL-A-8625, TYPE II, CLASS 2, DYE GREY, SIMILAR IN COLOR TO AMS-STD-595 NO. 16251, DUPLEX SEALED, EXCEPT NOTED CENTER GROOVE OD AREA TO BE CHEMICAL CONVERSION COATED PE

10、R MIL-DTL-5541, CLASS 3. /4/ SLEEVES SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS7510. THE QPL IS AVAILABLE AT www.eAuditN. /5/ IDENTIFICATION: MARK PER AS478-15A OR AS478-30

11、 USING .062 OR LARGER CHARACTERS. MARK AS A MINIMUM THE MANUFACTURERS NAME AND/OR CAGE CODE, COMPLETE “AS” NUMBER, AND DATE OF MANUFACTURE IN ACCORDANCE WITH MIL-STD-130. SIZES 20 AND SMALLER MAY BE INDIVIDUALLY BAGGED WITH A TAG PER AS478-35D CONTAINING THE PREVIOUS INFORMATION. /6/ OTHER DIMENSION

12、S AND TOLERANCES NOT SPECIFIED ARE CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPATIBILITY WITH THE ASSEMBLY AND COMPLIANCE WITH THE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION. 8. INTERPRETATION OF DRAWING PER AS4296. 9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; R

13、EQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACE TO BE 125 MICROINCHES Ra. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. DIMENSION AND TOLERANCE PER ASME Y14.5-2009. 12. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, A

14、NGULAR DIMENSIONS 030. /13/ EXAMPLE OF PART NUMBER: AS7514 A 32 BASIC PART NUMBER MATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZE IN .062 INCH INCREMENTS (SEE TABLE 1) EXAMPLE OF PART NUMBER: AS7514A32. 14. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE U

15、SER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.