SAE AS 8013A-1996 Minimum Performance Standard for Direction Instrument Magnetic (Gyroscopically Stabilized)《磁性方向仪(陀螺固定)的最低性能要求》.pdf

1、AEROSPACESTANDARDAS8013Issued 1983-06Revised 1996-09REV.AMINIMUM PERFORMANCE STANDARDFORDIRECTION INSTRUMENT, MAGNETIC (GYROSCOPICALLY STABILIZED)FOREWORDChanges in the revision are format/editorial only.1. SCOPE:This SAE Aerospace Standard (AS) establishes the minimum requirements for design and qu

2、alification of equipment identified as Gyroscopically Stabilized Magnetic Direction Instruments.1.1 Purpose:This document defines minimum performance requirements under standard and environmental conditions for Gyroscopically Stabilized Magnetic Direction Instruments for use in aircraft.2. APPLICABL

3、E DOCUMENTS:The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text o

4、f this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.SAE Technical Standards Board Rules provide that: “This report is published by SAE to a

5、dvance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least

6、 every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2008 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mean

7、s, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Reaff

8、irmed 2008-02SAE AS8013 Revision A- 2 -2.1 RTCA Publications:Available from RTCA Inc., 1140 Connecticut Avenue, NW, Suite 1020, Washington, DC 20036.RTCA Document No. DO-160A, “Environmental Conditions and Test Procedures for Airborne Equipment” dated January 19802.2 FAR Publications:Available from

9、Federal Aviation Administration, 800 Independence Avenue, SW, Washington, DC 20591.Federal Aviation Regulation 25.13593. GENERAL REQUIREMENTS:3.1 Operation of Controls:The operation of controls intended for use during flight, if any, in all possible position combinations and sequences shall not resu

10、lt in a condition whose presence or continuation would be detrimental to the continued performance of the equipment.3.2 Accessibility of Controls:Controls which are not normally adjusted in flight shall not be readily accessible to flight personnel, when the equipment is installed in accordance with

11、 the manufacturers instructions.3.3 Compatibility of Components:If the equipment components require matching for proper operation, they shall be identified in a manner that will provide for proper matching. The instructions furnished by the manufacturer must contain data detailing these limitations.

12、3.4 Fire Resistance:Except for small parts (such as knobs, fasteners, seals, grommets, and small electrical parts) that would not contribute significantly to the propagation of a fire, all materials must be self-extinguishing when tested in accordance with the requirements of Federal Aviation Regula

13、tion 25.1359 (d) and Appendix F thereto, with paragraph (b) of Appendix F or may be configured as used.3.5 Interchangeability:Instruments and components which are identified with the same manufacturers part number shall be interchangeable.SAE AS8013 Revision A- 3 -3.6 Malfunction Indication:Integral

14、 means shall be provided to indicate failures and/or the existence of the following conditions:a. System in fast alignment mode, required of electrical instruments except manually caged indicators with automatic release.b. Gyro operating at speed below the minimum designated by the manufacturer for

15、the instrument to meet the performance requirements herein. The requirement applies to electrical and remotely operated instruments.Additionally, the indicator or display of the repeating or remote indicating type of gyroscopically stabilized instrument shall be provided with means to indicate the f

16、ollowing failures:c. Loss of synchro excitationd. A mechanical obstruction in the indicator dial drive mechanisme. Primary power loss to the indicator or displayf. Servo Amplifier power lossg. Electrical failure in the servo drive motorThe indicating means shall indicate the failure or malfunction i

17、n an unambiguous manner. The indicating means may be a single indication of any or all of the preceding conditions or failures.3.7 Instrument Cover Glass Reflectance:The total reflectance of the instrument cover glass including the integral lighting wedge, if applicable, shall not exceed 10 percent

18、of the incident light. This reflectance applies over the visible light spectrum from 450 nanometers to 600 nanometers, and over an incident solid angle of 60 degrees perpendicular to the viewing plane.3.8 Indicating Method:One of the following methods of indication shall be employed:Method I Rotatin

19、g dial display with fixed lubber line. The dial shall rotate counterclockwise for right turns.Method II Horizontal scale display with fixed lubber line. The graduations shall move to the left for right turns.Method III Rotating pointer with fixed graduated dial. Pointer shall rotate clockwise for ri

20、ght turns. Dialposition may be settable.SAE AS8013 Revision A- 4 -3.9 Operating Limits:The instrument shall indicate heading throughout the 360 degree scale range. During dives, climbs, and banks of up to at least 55 degree displacement from level attitude, the instrument shall remain functional; ho

21、wever, the heading error involved through the gimbal system need not be corrected. The system may be provided with means to permit deactivating the slaving means during maneuvers.3.10 Dial Markings:3.10.1 Graduations: The indicators shall be provided with degree graduations at intervals not to excee

22、d 5 degrees, with major graduations every 10 degrees and with numerals at intervals not greater than 30 degrees, except that the 0, 90, 180, and 270 degrees positions may be marked N, E, S, and W, respectively.3.10.2 Visibility: Index and dial markings shall be visible from any point within the uppe

23、r half of a frustum of a cone, the side of which makes an angle of at least 30 degrees with the perpendicular to the dial and the small diameter of which is the aperture of the instrument case. At least two numerals shall be visible simultaneously.3.11 Caging Provisions:Unless the gyro assembly has

24、unrestricted freedom of operation in the pitch and roll axes, a means shall be provided for caging and/or releveling the gyro. A means shall be provided to indicate when the gyro is caged, except when it is not possible to leave the gyro in the caged condition.3.12 Compensation:Means shall, if neces

25、sary, be provided for compensating for single cycle (hard iron) error. Change in deviation shall be smooth and continuous.3.13 Synchronization Provision:Automatic or manual means shall be provided to bring the indicated heading into alignment with the magnetic heading. An indication of alignment and

26、/or failure to align shall be provided.3.14 Self-Test Capability:If the equipment contains integral arrangements to permit preflight and/or inflight self-test checks on the operation of the equipment and/or in combination with other aircraft subsystems, a means shall be provided to permit deactivati

27、ng a using subsystem which might be adversely affected during the self-test cycle. In flight self-test activating controls shall provide a means to warn the pilot of this mode of operation.SAE AS8013 Revision A- 5 -3.15 Identification:The following information shall be legibly and permanently marked

28、 on the instrument or nameplate attached thereto:a. Name of instrumentb. Manufacturers name or trademark and part numberc. Manufacturers serial number or date of manufactured. Environmental categoriese. SAE AS8013A or equivalent approval identification3.16 Case Grounding:Metallic or other conductive

29、 instrument cases shall be connected to aircraft ground through a connector pin.4. MINIMUM PERFORMANCE REQUIREMENTS UNDER STANDARD TEST CONDITIONS:4.1 Starting:Rated instrument performance rotor speed shall be achieved within 3 minutes after normal power is applied for both air and electric operated

30、 instruments. If the instrument incorporates a gyro speed monitoring device which provides a positive indication when the gyro speed is below that necessary to meet instrument performance, the starting time may exceed 3 minutes, but shall not be greater than 5 minutes.4.2 Scale Error:When the magnet

31、ic-sensitive unit is placed on magnetic headings at 30 degree intervals, starting from north, each indication shall correspond to the actual magnetic heading within 2 degrees.4.3 Compensation:With the instrument on a north heading and the magnetic compensator adjusted for minimum effect, the scale e

32、rror with the compensator shall not differ from the scale error without the compensator by more than 2 degrees. The test shall be repeated with the instrument on an east heading.SAE AS8013 Revision A- 6 -4.4 Turn Error:Two minutes after resumption of straight and level flight the scale error resulti

33、ng from a coordinated turn of 180 degrees in 1 minute at a true airspeed of 180 miles per hour (289 km/h) shall be within 2 degrees. The error shall have been obtained from a turn which was begun from an easterly heading.An optional test procedure to demonstrate the effects of turn error is as follo

34、ws:With the system synchronized on an east heading, set the magnetic heading sensor to a south heading, and allow the system to operate for 1 minute. Set the magnetic heading sensor to an east heading and allow the system to operate for 2 minutes. The resultant heading shall duplicate the initial sy

35、nchronized reading within 2 degrees.4.5 Heeling:When the gyroscope is tilted 10 degrees about the roll or pitch axis and rotated 360 degrees in azimuth in 30-degree increments, the indicated headings shall not differ from the indicated headings with the gyroscope in its normal level position by more

36、 than 4 degrees. The instrument shall remain at each heading for 5 minutes before reading.4.6 Field Strength Variation Effect:With the transmitter at a total field of 0.57 .02 gauss (.057 .002 mT) at a dip angle of 72 1 degrees and the compass at a null, the null shall not vary more than 2 degrees w

37、hen the dip angle is changed to 80 1 degrees.5. MINIMUM PERFORMANCE REQUIREMENTS UNDER ENVIRONMENTAL CONDITIONS:Unless otherwise specified herein, the procedures applicable to a determination of the performance of directional instruments under environmental conditions are set forth in Radio Technica

38、l Commission for Aeronautics (RTCA) Document No. DO-160A, entitled “Environmental Conditions and Test Procedures for Airborne Equipment” dated January 1980. Performance tests specified after subjection to test environments may be made after exposure to several environmental conditions. The order of

39、tests shall be in accordance with paragraph 3.2, page 4, of DO-160A. The test procedures specified or referenced are satisfactory for use in determining the performance of directional instruments under standard and extreme environmental conditions. Alternate approved test procedures that provide equ

40、ivalent results may be used. As many instruments as deemed necessary to demonstrate that all instruments will comply with the requirements of this paragraph, shall be tested in accordance with the manufacturers recommendations.SAE AS8013 Revision A- 7 -5.1 Performance Standard for Use During Environ

41、mental Tests:The following performance standard shall be used when performance testing during an environmental test is required:a. There shall be no more than 2 degrees of scale error (indicated heading-vs-actual magnetic heading).5.2 Temperature - Altitude - Humidity:a. Low-Temperature - The instru

42、ment shall be subjected to the tests of DO-160A, paragraph 4.4. When specified the instrument shall operate electrically and mechanically and the requirements of paragraph 5.1 of this Standard shall be met. Following the test, the requirement of paragraph 4.1 through 4.3 of this Standard shall be me

43、t at standard conditions.b. High Temperature - The instrument shall be subjected to the tests of DO-160A, paragraph 4.5. There shall be no evidence of materials such as potting and sealing compounds exuding or dripping from the instrument. When specified, the instrument shall operate electrically an

44、d mechanically and the requirements of paragraph 5.1 of this Standard shall be met. Following the test, the requirements of paragraph 4.1 through 4.3 of this Standard shall be met.c. Altitude - The instrument shall be subjected to the tests of DO-160A, paragraphs 4.6.1, 4.6.2, and 4.6.3. When specif

45、ied the instrument shall operate electrically and mechanically and the requirements of paragraph 5.1 of this Standard shall be met. After being subjected to the tests of paragraph 4.6.2, the requirements of paragraph 4.1 through 4.3 of this Standard shall be met and after being subjected to the test

46、s of paragraph 4.6.3 the requirements of paragraphs 4.1 through 4.3 of this Standard shall be met.d. Humidity - The instrument shall be subjected to the tests of DO-160A, paragraph 6. After the instrument is subjected to the appropriate tests of paragraph 6, it shall meet the requirements of paragra

47、ph 4.1 through 4.3 of this Standard.5.3 Shock:The instrument shall be subjected to the tests of DO-160A, paragraphs 7.1 and 7.2.a. After the instrument is subjected to the tests of paragraph 7.1, it shall meet the requirements of paragraph 4.1 through 4.3 of this Standard under standard conditions.b

48、. Following the tests of paragraph 7.2, the instrument or dummy load shall have remained in its mounting and no parts of the instrument or its mounting base shall have become detached and free of the shock tested equipment.SAE AS8013 Revision A- 8 -5.4 Vibration:The instrument shall be subjected to

49、the tests of DO-160A, paragraph 8.3. When specified the instrument shall operate electrically and mechanically and the requirements of paragraph 5.1 shall be met. Following the test, the requirements of paragraph 4.1 through 4.3 of this Standard shall be met at standard conditions.5.5 Power Input:a. Normal Electrical Input Variation:(1) The instrument shall be subjected to the tests of DO-160A, paragraph 16.3.1. When specified, it shall meet the requirements of paragraph 5.1 of this Standard. Also the gyro rotor shall start and continue to rotate at the low volta