SAE AS 81511 15-2014 ACCESSORY SEALING CONTACT PLUG CONNECTOR ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING (SERIES 1 OR 2).pdf

1、AEROSPACE STANDARD ACCESSORY, SEALING CONTACT, PLUG, CONNECTOR, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING (SERIES 1 OR 2)AS81511/15Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or tr

2、ansmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org

3、SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935 AS81511/15SHEET 1 OF 2PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineer

4、ing sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirme

5、d, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/15RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO PERMIT THE CANCELLATION AND SUPERSESSIO

6、N OF MIL-C-81511/15 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - SEALING CONTACT PLUG AEROSPACE STANDARD AS81511/15SHEET 2 OF 2ACCESSORY, SEALING CONTACT, PLUG, CONNECTOR, EL

7、ECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING (SERIES 1 OR 2)TABLE 1 PART NUMBER AND CHARACTERISTICS PARTNUMBER CONTACT SIZE(REFERENCE)ADIAMETER COLOR APPROX. WEIGHT (LB) M81511/15-22 23-22 .050/.045 (1.27/1.14) WHITE .000046 M81511/15-20 20-20 .070/.065 (1.78/1.65) RED .

8、000093 M81511/15-16 16-16 .095/.090 (2.41/2.29) BLUE .000174 M81511/15-12 12-12 .145/.140 (3.68/3.56) YELLOW .000556 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: SEALING CONTACT PLUGS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE

9、 1. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. THESE PLUGS ARE USED WITH UNWIRED CONTACTS IN CONNECTORS CONFORMING TO AS81511. 2. MATERIAL: CONT

10、ACT SEALING PLUG MATERIAL SHALL BE POLYTETRAFLUORETHYLENE (PTFE) IN ACCORDANCE WITH ASTM D1710. PLASTIC ROD, MOLDED AND EXTRUDED - TEMPERATURE LIMIT 200 C MINIMUM. THE MATERIAL USED TO FABRICATE SEALING PLUGS SHALL BE POLYTETRAFLUOROETHYLENE (PTFE) IN ACCORDANCE WITH ASTM D1710, OR FLUORINATED ETHYL

11、ENE PROPYLENE (FEP) IN ACCORDANCE WITH ASTM D2116, OR PERFLUOROALKOXY (PFA) IN ACCORDANCE WITH ASTM D3307, OR POLYPHENYLSULFONE (PPSU) IN ACCORDANCE WITH ASTM D6394. 3. COLOR: COLOR OF ITEMS SHALL BE IN ACCORDANCE WITH EIA-359. 4. RESISTIVITY: MATERIAL RESISTIVITY SHALL BE NOT LESS THAN 100 MEGOHMS

12、WHEN TESTED IN ACCORDANCE WITH ASTM D257. 5. INSTALLATION: THE SEALING PLUG IS DESIGNED FOR USE WITH AN UNWIRED CONTACT INSTALLED IN CONNECTOR APPLICATIONS. THE SEALING PLUG SHALL BE PUSHED INTO THE GROMMET UNTIL THE HEAD IS POSITIONED AGAINST THE END OF THE UNWIRED CONTACT. 6. WORKMANSHIP: THE ITEM

13、 SHALL BE FREE FROM FLASH AND BURRS. THE LENGTH OF DIAMETER A SHALL BE FREE OF ALL MOLDING MARKS, PROTRUSIONS, AND BLEMISHES. MOLDING MARKS, PROTRUSIONS, AND BLEMISHES FROM GATE CUTOFFS ARE PERMISSIBLE BUT ONLY ON THE PLUG ENDS AND SHALL NOT BE GREATER THAN .005 INCH IN HEIGHT. APPLICATION NOTES: 1.

14、 AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.