SAE AS 81511 26-2014 CONNECTOR PLUG ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING CRIMP TYPE CONTACTS (CLASS A F AND E - SERIES 1).pdf

1、AEROSPACE STANDARD CONNECTOR, PLUG, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS (CLASS A, F AND E - SERIES 1)AS81511/26Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval syste

2、m or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServices

3、ae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935AS81511/26SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalanden

4、gineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,rea

5、ffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/26RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITTEN TO PERMIT THE CANCELLATION AND SUPER

6、SESSION OF MIL-C-81511/26 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR PLUG AEROSPACE STANDARD AS81511/26SHEET 2 OF 3CONNECTOR, PLUG, ELECTRICAL, CIRCULAR, HIGH DEN

7、SITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS (CLASS A, F AND E - SERIES 1)TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .005 0.13 .233 5.92 1.445 36.70 .015 0.38 .400 10.16 1.460 37.08.228 5.79 1.380 35.05 1.525 38.74 TABLE 2 - F

8、IGURE 1 DIMENSIONS/CONFIGURATION SHELLSIZEADEFTHREADKAPBSCBPBSCCP BSCDP BSCJJ 8.4015(10.20) .3955(10.05) .430(10.92) .424(10.77) .422(10.72) .407(10.34)1/2-28UNEF-2A.850(21.59) .830(21.08)105 140 215 265 .382(9.70).373(9.47) 10.5265(13.37) .5205(13.22) .555(14.10) .549(13.94) .548(13.92) .533(13.54)

9、5/8-28UN-2A .975(24.77) .955(24.26)95 141 208 236 .507(12.88) .498(12.65)14.7765(19.72) .7705(19.57) .805(20.45) .799(20.29) .798(20.27) .783(19.89)7/8-28UN-2A 1.225(31.12) 1.205(30.61)95 141 208 236 .757(19.23) .746(18.95)16.9025(22.92) .8965(22.77) .930(23.63) .924(23.47) .924(23.47) .909(23.09)1-

10、28UN-2A 1.350(34.29) 1.330(33.78)80 142 196 293 .883(22.43) .872(22.15)181.0265(26.07) 1.0205(25.92) 1.055(26.80) 1.049(26.64) 1.048(26.62) 1.033(26.24)1 1/8-28UN-2A1.475(37.47) 1.455(36.96)80 142 196 293 1.007(25.58) .996(25.30)201.1515(29.25) 1.1455(29.10) 1.180(29.97) 1.174(29.82) 1.173(29.79) 1.

11、158(29.41)1 1/4-28UN-2A1.624(41.25) 1.604(40.74)80 142 196 293 1.132(28.75) 1.121(28.47)221.2765(32.42) 1.2705(32.27) 1.305(33.15) 1.299(32.99) 1.298(32.97) 1.283(32.59)1 3/8-28UN-2A1.749(44.42) 1.729(43.92)80 142 196 293 1.257(31.93) 1.246(31.65) 241.4015(35.60) 1.3955(35.45) 1.430(36.32) 1.408(35.

12、76) 1.423(36.14) 1.408(35.76)1 1/2-28UN-2A1.874(47.60) 1.854(47.09)80 142 196 293 1.382(35.10) 1.371(34.82)REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 1. DIMENSIONS ARE IN

13、 INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511, FIGURE 8. THE .400 MAX.

14、DIMENSION IN FIGURE 1 IS THE DISTANCE FROM THE FRONT OF THE SHELL TO THE POINT AT WHICH A GAGE RING, HAVING THE SAME BASIC DIAMETER AS THE RECEPTACLE SHELL, ENGAGES THE SPRING MEMBER. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. AEROSPACE STANDARD AS81511/26SHEET 3 OF 3CONNECTOR, PLUG, ELECT

15、RICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, CRIMP TYPE CONTACTS (CLASS A, F AND E - SERIES 1)3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS

16、ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/26ED01P1. M81511/26 E D 01 P 1 BASIC PART NUMBERCLASSSHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR KEY POSITIONS 4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS81969

17、/2 INSERTION TOOL, AS81969/3 REMOVAL TOOL. 6. MATING CONNECTOR: THIS PLUG MATES DIRECTLY WITH AS81511/21, /23, AND /25 RECEPTACLES. 7. CONNECTOR WEIGHT: THE CONNECTOR REFERENCE WEIGHTS ARE LISTED IN TABLE 3. TABLE 3 - CONNECTOR WEIGHT SHELL SIZE WEIGHT (REFERENCE - POUNDS) 1/ 24 (CODE J) .140 22 (CO

18、DE H) .122 20 (CODE G) .108 18 (CODE F) .089 16 (CODE E) .071 14 (CODE D) .062 10 (CODE B) .040 8 (CODE A) .031 1/ REMOVABLE CRIMP CONTACTS NOT INCLUDED IN WEIGHT. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. SPECIFICATION NOTES: NOTICE THIS DOCUMENT R

19、EFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.