SAE AS 81511 51-2014 CONNECTOR RECEPTACLE FLANGE MOUNT ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A F AND.pdf

1、AEROSPACE STANDARD CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL,CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMPTYPE CONTACTS (CLASS A, F, AND W - SERIES 4)AS81511/51Copyright 2014 SAE International All rights reserved. No part of this publication may be

2、reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fa

3、x: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5935AS81511/51SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide that: “This report ispublishedby S

4、AE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five

5、years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/51RATIONALE THIS DETAIL SPECIFICATION SHEET IS WRITT

6、EN TO PERMIT THE CANCELLATION AND SUPERSESSION OF MIL-C-81511/51 WITH THIS DOCUMENT. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR RECEPTACLE, FLANGE MOUNT (SERIES 4) AEROSPACE STANDARD

7、 AS81511/51SHEET 2 OF 3CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4)FIGURE 1 - CONNECTOR RECEPTACLE, FLANGE MOUNT (SERIES 4) (CONTINUED) TABLE 1 - FIGURE 1 METRI

8、C EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.08 .035 0.89 .116 2.95 .775 19.69 .005 0.13 .065 1.65 .125 3.18 1.167 29.64.006 0.15 .073 1.85 .126 3.20 1.187 30.15 .010 0.25 .075 1.91 .200 5.08 .015 0.38 .090 2.29 .230 5.84 .016 0.41 .094 2.39 .765 1

9、9.43 TABLE 2 - FIGURE 1 DIMENSIONS SHELLSIZEBDFTHREAD G H PARBSCBRBSCCR BSCDR BSCFF RADIUS EE BSC POSITION 1234568.553(14.05) .547(13.89) .430(10.92) .424(10.77) 1/2-28UNEF-2A .820(20.83) .804(20.42) .599(15.21) .589(14.96).640(16.26).630(16.00) 128 - - - .120 (3.05) .100 (2.54) 40 40 40 40 40 4010.

10、678(17.22) .672(17.07) .555(14.10) .549(13.94) 5/8-28UN-2A .945(24.00) .929(23.60) .724(18.39) .714(18.14).765(19.43) .755(19.18)105 140 215 265 .120 (3.05) .100 (2.54) 60 46 46 60 89 6014.928(23.57) .922(23.42) .805(20.45) .799(20.29) 7/8-28UN-2A 1.133(28.78) 1.117(28.37) .911(23.14) .901(22.89)1.0

11、15(25.78) 1.005(25.53)105 140 215 265 .120 (3.05) .100 (2.54) 60 46 46 60 89 60161.054(26.77) 1.048(26.62) .930(23.63) .924(23.47) 1-28UN-2A 1.258(31.95) 1.242(31.55) .974(24.74) .964(24.49)1.140(28.96) 1.130(28.70)105 140 215 265 .150 (3.81) .130 (3.30) 50 50 50 50 50 50181.178(29.92) 1.172(29.77)

12、1.055(26.80) 1.049(26.64) 1 1/8-28UN-2A 1.351(34.32) 1.335(33.91) 1.067(27.10) 1.057(26.85)1.265(32.13) 1.255(31.88)105 140 215 265 .150 (3.81) .130 (3.30) 50 50 50 50 50 50AEROSPACE STANDARD AS81511/51SHEET 3 OF 3CONNECTOR, RECEPTACLE, FLANGE MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONN

13、ECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4)REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INCHES A

14、ND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511, FIGURE 8. COLOR BANDS SHALL BE BL

15、UE IN COLOR, .125 MAX. WIDTH AND SHALL BE VISIBLE WHEN MOUNTED. INSERT PROTRUSION FOR INSERTS CONTAINING SIZE 12 CONTACTS SHALL BE .070/.020. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. 3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF THE LETTER M, THE BASIC SPECIFICATION NUMBER/AP

16、PLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/51FD01P1. M81511/51 F D 01 P 1 BASIC PART NUMBERCLASSSHELL SIZE INSERT ARRANGEMENT CONTACT DESIGNATOR KEY POSITIONS 4. SHELL POLAR

17、IZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS81969/16 INSERTION/REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES DIRECTLY WITH AS81511/6 AND /56 PLUGS. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT RECOMMENDED FOR NEW DESIGN. 2. FOR SHELL SIZES 20,

18、22, AND 24, USE AS81511/21 OR /41. SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOC

19、ATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.