SAE AS 81582 1A-2011 CONNECTORS ELECTRIC BAYONET COUPLING UMBILICAL RECEPTACLE JAM NUT MOUNTING RFI SHIELDED CRIMP CONTACT CLASS E《E类压接接触件射频干扰屏蔽式的锁紧螺母中央插座连接用电气卡口连接器》.pdf

1、 AEROSPACE STANDARD CONNECTORS, ELECTRIC, BAYONET, COUPLING, UMBILICAL RECEPTACLE, JAM NUT MOUNTING, RFI SHIELDED, CRIMP CONTACT, CLASS E AS81582/1 Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any

2、 form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS:

3、http:/www.sae.org ISSUED2004-04REVISED 2011-11REAFFIRMED 2017-03THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS81582/1 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: AS81582 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thes

4、tateoftechnical andengineering sciences. The useofthis reportisentirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichti

5、me it may berevised, reaffirmed, stabilized, or cancelled. SAEinvites your written comments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81582/1A RATIONALE AS81582/1A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR

6、REVIEW POLICY. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS81582. FIGURE 1 CONNECTOR CONFIGURATION AND DIMENSIONS AEROSPACE STANDARD AS81582/1 SHEET 2 OF 4 REV. A CONNECTORS, ELECTRIC, BAYONET, COUPLING, U

7、MBILICAL RECEPTACLE, JAM NUT MOUNTING, RFI SHIELDED, CRIMP CONTACT, CLASS E FIGURE 1 CONNECTOR CONFIGURATION AND DIMENSIONS (CONTINUED) FIGURE 1 CONNECTOR CONFIGURATION AND DIMENSIONS (CONTINUED) AEROSPACE STANDARD AS81582/1 SHEET 3 OF 4 REV. A CONNECTORS, ELECTRIC, BAYONET, COUPLING, UMBILICAL RECE

8、PTACLE, JAM NUT MOUNTING, RFI SHIELDED, CRIMP CONTACT, CLASS E TABLE 1 METRIC EQUIVALENT EXAMPLES INCHES MM INCHES MM INCHES MM INCHES MM INCHES MM .003 .004 .005 .006 .010 .015 .019 .022 .024 .026 .029 .062 .066 .072 .08 .10 .13 .15 .25 .38 .48 .56 .61 .66 .74 1.57 1.68 1.83 .074 .079 .090 .093 .09

9、9 .107 .122 .125 .128 .129 .140 .156 .233 .257 1.88 2.01 2.29 2.36 2.51 2.72 3.10 3.18 3.25 3.28 3.56 3.96 5.92 6.53 .306 .342 .367 .400 .416 .572 .616 .624 .625 .626 .635 .640 .650 7.77 8.70 9.32 10.16 10.57 14.53 15.65 15.85 15.88 15.90 16.13 16.26 16.51 .745 .790 .800 .989 .993 1.042 1.062 1.1875

10、 1.279 1.284 1.322 1.332 1.376 1.381 18.92 20.07 20.32 25.12 25.22 26.47 26.97 30.16 32.49 32.61 33.58 33.83 34.95 35.08 1.452 1.464 1.470 1.480 1.500 1.505 1.515 1.682 1.710 1.712 1.949 1.960 2.030 2.045 36.88 37.19 37.34 37.59 38.10 38.23 38.48 42.72 43.43 43.48 49.50 49.78 51.56 51.94 FIGURE 2 -

11、KEYWAY POSITIONS - RECEPTACLE TYPE SHELL SHELL SIZE 22 - FRONT FACE VIEW TABLE 2 KEYWAY POSITIONS KEY AND KEYWAY POSITION NUMBER ARq, APq BASIC BRq, BPq BASIC CRq, CPq BASIC DRq, DPq BASIC A (NORMAL) 105 140 215 265 B 18 149 192 259 C 92 152 222 342 D 84 152 204 334 E 24 135 199 240 F 98 152 268 330

12、 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS81582. 1. DESIGN DIMENSIONS ARE IN INCHES. METRIC EQUIVALENTS IN TABLE 1 ARE GIVEN FOR INFORMATION PURPOSES ONLY. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .010 FOR DECIMALS AND .5 DEGREES FOR ANGLES. DIME

13、NSIONS SHOWN APPLY AFTER PLATING. NORMAL MATING KEYWAY LOCATION SHOWN. THE .572 MAX. DIMENSION IN DETAIL B-B IS THE DISTANCE FROM THE FRONT OF THE SHELL TO THE POINT AT WHICH A GAGE PIN, HAVING THE SAME BASIC DIAMETER AS THE MATING CONTACT WITH A SQUARE END, ENGAGES THE SOCKET CONTACT SPRING. THIS C

14、ONNECTOR IS SHELL SIZE 22. INSERT ARRANGEMENTS: SHALL BE AS SPECIFIED IN MIL-STD-1672. SERVICE RATING: I. SOCKET CONTACTS: SOCKET CONTACTS SHALL CONFORM TO AS39029/32. AEROSPACE STANDARD AS81582/1 SHEET 4 OF 4 REV. A CONNECTORS, ELECTRIC, BAYONET, COUPLING, UMBILICAL RECEPTACLE, JAM NUT MOUNTING, RF

15、I SHIELDED, CRIMP CONTACT, CLASS E PIN CONTACTS: PIN CONTACTS SHALL CONFORM TO AS39029/31. WEIGHT: THE WEIGHT, INCLUDING CONTACTS, MOUNTING NUT AND O-RINGS, SHALL NOT EXCEED 0.31 POUND. CONNECTORS: ALL REQUIREMENTS OF AS81582 FOR CONNECTORS SHALL APPLY, EXCEPT AS FOLLOWS: SHELL MATERIAL: SHALL BE CO

16、RROSION RESISTING STEEL PER ASTM A484/ASTM A582, TYPE 303 SE. FINISH: THE SHELL FINISH SHALL BE CADMIUM PLATE PER QQ-P-416, TYPE II, CLASS 3. THE RESULTANT FINISH SHALL BE CLEAR TO LIGHT IRIDESCENT. A PRELIMINARY PLATING OF SILVER SHALL NOT BE USED. DIELECTRIC MATERIAL: RIGID DIELECTRIC MATERIAL SHA

17、LL BE GLASS FILLED MOLDABLE EPOXY ON SOCKET CONTACT CONNECTORS. CONTACT RETENTION: THE CONTACT RETENTION TEST SHALL BE DONE WITHOUT REAR ACCESSORIES, AND MINIMUM AXIAL LOADS SHALL BE 20 POUNDS FOR SIZE 20 CONTACTS AND 30 POUNDS FOR SIZE 12 CONTACTS. FLUID IMMERSION TEST: DURING QUALIFICATION TESTING

18、, THE FRONT INSERT OF SAMPLE NUMBER FOUR CONNECTORS ONLY SHALL BE SUBJECTED TO THE FLUID IMMERSION TEST USING JP-5 FUEL IN ACCORDANCE WITH MIL-DTL-5624. MATING CONNECTOR: SEE AS81582/2. INSERTION AND EXTRACTION TOOLS: SEE AS81969/17 AND /19. GROMMET SEALING PLUGS: SEE MS27488. CABLE SUPPORT: SEE MS2

19、7291. CLOSED RIGHT ANGLE CABLE SUPPORT: SEE MS27558-7. RIGHT ANGLE CABLE SUPPORT: SEE MS27559-7. PART NUMBER M81582/1E03SA IS THE SAME AS M81582/1E3-SA1 OF PREVIOUS REVISIONS. M81582/1 E 03 S A BASIC PART NUMBER CLASS INSERT ARRANGEMENT CONTACT DESIGNATOR (P-PIN, S-SOCKET) POLARIZATION (SEE TABLE 2)

20、 SPECIFICATION NOTES NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS,

21、 NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.