SAE AS 81582 4A-2012 CONNECTOR ADAPTER RFI SHIELDED CABLE TO ELECTRIC CONNECTOR《电缆至电气连接器的射频干扰屏蔽连接器转接座》.pdf

1、 AEROSPACE STANDARD CONNECTOR ADAPTER, RFI SHIELDED, CABLE TO ELECTRIC CONNECTOR AS81582/4 Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyi

2、ng, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-04REVISED 2012-02REAFFIRMED

3、2017-03THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935 AS81582/4 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS81582 SAE Technical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis re

4、portis entirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.” SAE reviews eachtechnical reportatleastevery five years at whichtime it may berevised, reaffirmed, stabilized, or cancelle

5、d. SAEinvites your written comments and suggestions. SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81582/4A RATIONALE AS81582/4A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR PROCURING THE

6、 PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS81582. FIGURE 1 ADAPTER CONFIGURATIONS INCHES MM INCHES MM INCHES MM INCHES MM INCHES MM .002 .008 .010 .014 .015 .017 .018 .020 .022 .025 .030 .035 .036 .040 .050 .070 .075 .080 .05 .20 .25 .36 .38 .43

7、 .46 .51 .56 .64 .76 .89 .91 1.02 1.27 1.78 1.91 2.03 .085 .100 .115 .135 .145 .170 .180 .190 .240 .260 .400 .430 .440 .464 .470 .490 .495 .500 2.16 2.54 2.92 3.43 3.68 4.32 4.57 4.83 6.10 6.60 10.16 10.92 11.18 11.79 11.94 12.45 12.57 12.70 .510 .585 .595 .671 .675 .683 .713 .723 .750 .760 .795 .80

8、0 .803 .805 .813 .820 1.015 1.025 12.95 14.86 15.11 17.04 17.15 17.35 18.11 18.36 19.05 19.30 20.19 20.32 20.40 20.45 20.65 20.83 25.78 26.04 1.062 1.065 1.067 1.085 1.115 1.118 1.122 1.131 1.134 1.153 1.155 1.163 1.166 1.168 1.172 1.194 1.198 1.245 26.97 27.05 27.10 27.56 28.32 28.40 28.50 28.73 28

9、.80 29.29 29.34 29.54 29.62 29.67 29.77 30.33 30.43 31.62 1.250 1.255 1.261 1.264 1.450 1.454 1.800 1.810 1.910 1.930 2.068 2.098 2.290 2.310 2.465 2.485 2.845 2.865 31.75 31.88 32.03 32.11 36.83 36.93 45.72 45.97 48.51 49.02 52.53 53.29 58.17 58.67 62.61 63.12 72.26 72.77 AEROSPACE STANDARD AS81582

10、/4 SHEET 2 OF 3 REV. A CONNECTOR ADAPTER, RFI SHIELDED, CABLE TO ELECTRIC CONNECTOR FIGURE 1 - ADAPTER CONFIGURATIONS (CONTINUED) FIGURE 2 TYPE A TERMINATION FIGURE 3 TYPE B TERMINATION TABLE 1 TERMINATION CONFIGURATIONS/DIMENSIONS DASH NUMBER CONFIGURATION TERMINATION TYPE X DIMENSION WEIGHT (LBS)

11、-1 STRAIGHT A 2.865/2.845 0.12 MAX. -2 STRAIGHT B 2.485/2.465 0.12 MAX. -3 105 DEGREES A 2.310/2.290 0.18 MAX. -4 105 DEGREES B 1.930/1.910 0.18 MAX. AEROSPACE STANDARD AS81582/4 SHEET 3 OF 3 REV. A CONNECTOR ADAPTER, RFI SHIELDED, CABLE TO ELECTRIC CONNECTOR FIGURE 4 RETAINING RING CONFIGURATION RE

12、QUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS81582. 1. DESIGN: ALL DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE PROVIDED FOR INFORMATION PURPOSED ONLY AND ARE BASED ON 1 INCH = 25.4 MILLIMETERS. THE .015/.017 RADIUS ALSO APPLI

13、ES TO THE REMOVABLE RETAINER RING DIAMETER OVER THE RETAINING RING WHICH IS 1.198/1.194. 2. PART NUMBER: EXAMPLE OF PART NUMBER M81582/04 -A 105 _ CONFIGURATION ANGLE (LEAVE BLANK FOR STRAIGHT CONFIGURATION) BASIC PART NUMBER TERMINATION TYPE NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTA

14、INS CADMIUM AS A PLATING MATERIAL AS REQUIRED BY THE BASE SPECIFICATION. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. SPECIFICATION NOTES: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORI

15、AL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPLICATION NOTES: 1. FOR USE WITH AS81582/2 CONNECTORS.