SAE AS 81659 33B-2017 CONNECTORS ELECTRICAL RECTANGULAR PLUG CRIMP CONTACTS (DUAL INSERT TYPE II CLASS 1 (-65 TO +125 SERIES 2 SHELL DESIGNATOR A).pdf

1、 AEROSPACE STANDARD CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS, (DUAL INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) AS81659/33Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system

2、or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae

3、.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2004-05REVISED2017-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.BFEDERAL SUPPLY CLASS 5935 AS81659/33 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS81659 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the sta

4、te oftechnicaland engineering sciences.The use ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaff

5、irmed,stabilized,orcancelled.SAEinvitesyourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81659/33B RATIONALE REVISION IS REQUIRED TO UPDATE THE CONNECTOR INSERT AND INSTALLING/REMOVAL TOOL REFERENCES. INCHES

6、 MM INCHES MM INCHES MM INCHES MM INCHES MM .006 .047 .060 .093 .115 .117 .118 .122 .15 1.19 1.52 2.36 2.92 2.97 3.00 3.10 .125 .133 .178 .198 .225 .235 .281 .297 3.18 3.38 4.52 5.03 5.72 5.97 7.14 7.54 .521 .541 .7185 .885 .897 .927 .947 1.367 13.23 13.74 18.25 22.48 22.78 23.55 24.05 34.72 1.387 1

7、.3915 1.427 1.437 1.447 1.541 1.720 1.730 35.23 35.34 36.25 36.50 36.75 39.14 43.69 43.94 1.985 2.015 2.320 2.440 2.450 2.783 3.095 3.125 50.42 51.18 58.93 61.98 62.23 70.69 78.61 79.38 FIGURE 1 CONNECTOR SUGGESTED PANEL CUTOUT/RECOMMENDED MATED POSITION AEROSPACE STANDARD AS81659/33 SHEET 2 OF 3 RE

8、V. B CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS, (DUAL INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 CONNECTOR CONFIGURATIONS AND DIMENSIONS AEROSPACE STANDARD AS81659/33 SHEET 3 OF 3 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACT

9、S, (DUAL INSERT, TYPE II, CLASS 1, (-65 C TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 CONNECTOR CONFIGURATIONS AND DIMENSIONS (CONTINUED) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81659. 1. DESIGN: CONNECTOR ACCESSORIES SHALL BE DESIGNED IN ACCORD

10、ANCE WITH FIGURES 1 AND 2. DIMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. NORMAL (01) POLARIZATION POSITION SHOWN, FOR ALTERNATE POSITIONS SEE AS81659. FOR LOCATION OF DATUMS G AND H, REFER TO AS81659 F

11、IGURE 6. 2. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH AS31571. 3. CONTACTS SHALL BE IN ACCORDANCE WITH AS39029/11 OR AS39029/12 AS APPLICABLE. 4. INSTALLING AND REMOVAL TOOLS SHALL BE IN ACCORDANCE WITH AS81969/1 OR AS81969/14. SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (l) LOCATE

12、D IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.