SAE AS 81659 69B-2017 CONNECTORS ELECTRICAL RECTANGULAR PLUG CRIMP CONTACTS (DUAL INSERT TYPE IV CLASS 1 (-65 TO +125 SERIES 2 SHELL DESIGNATOR A).pdf

1、 AEROSPACE STANDARD CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS, (DUAL INSERT, TYPE IV, CLASS 1, (-65 TO +125 C), SERIES 2, SHELL DESIGNATOR A) $6Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmi

2、tted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE W

3、EB ADDRESS: http:/www.sae.org ISSUED2004-05REVISED2017-09THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.B FEDERAL SUPPLY CLASS 5935 $6 SHEET 1 OF 4 REV. B PROCUREMENT SPECIFICATION: AS81659 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneeri

4、ng sciences. The useof this report is entirely voluntary, and its applicability andsuitabilityIRUDQSDUWLFXODUXVHLQFOXGLQJDQSDWHQWLQIULQJHPHQWDULVLQJWKHUHIURPLVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized,

5、or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit HTTP:/STANDARDS.SAE.ORG/AS81659/69B RATIONALE REVISION IS REQUIRED TO UPDATE THE CONNECTOR INSERT AND INSTALLING/REMOVAL TOOL REFERENCES. FIGURE 1 - CONNE

6、CTOR SUGGESTED PANEL CUTOUT/RECOMMENDED MATED POSITION INCH MM INCH MM INCHES MM INCHES MM INCHES MM .006 .047 .060 .093 .115 .117 .118 .122 0.15 1.19 1.52 2.36 2.92 2.97 3.00 3.10 .125 .133 .178 .198 .225 .235 .281 .297 3.18 3.38 4.52 5.03 5.72 5.97 7.14 7.54 .521 .541 .7185 .885 .897 .927 .947 1.2

7、15 13.23 13.74 18.25 22.48 22.78 23.55 24.05 30.86 1.367 1.387 1.3915 1.427 1.437 1.447 1.720 1.730 34.72 35.23 35.34 36.25 36.50 36.75 43.69 43.94 1.985 2.015 2.145 2.440 2.450 2.783 3.095 3.125 50.42 51.18 54.48 61.98 62.23 70.64 78.61 79.38 AEROSPACE STANDARD $6 SHEET 2 OF 4 REV. B CONNECTORS, EL

8、ECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS, (DUAL INSERT, TYPE IV, CLASS 1, (-65 TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 - CONNECTOR CONFIGURATIONS AND DIMENSIONS AEROSPACE STANDARD $6 SHEET 3 OF 4 REV. B CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS, (DUAL INSERT, TYPE IV, C

9、LASS 1, (-65 TO +125 C), SERIES 2, SHELL DESIGNATOR A) FIGURE 2 - CONNECTOR CONFIGURATIONS AND DIMENSIONS(CONTINUED) REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81659. 1. DESIGN: CONNECTOR ACCESSORIES SHALL BE DESIGNED IN ACCORDANCE WITH FIGURES 1 AND 2. D

10、IMENSIONS ARE IN INCHES AND APPLY AFTER PLATING. TOLERANCES: DECIMALS .010 UNLESS OTHERWISE SPECIFIED. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM. NORMAL (01) POLARIZATION POSITION SHOWN, FOR ALTERNATE POSITIONS SEE AS81659. FOR LOCATION OF DATUMS G

11、 AND H, REFER TO AS81659, FIGURE 6. 2. INSERT ARRANGEMENTS SHALL BE IN ACCORDANCE WITH AS31571. 3. CONTACTS SHALL BE IN ACCORDANCE WITH AS39029/11 OR AS39029/12 AS APPLICABLE. 4. INSTALLING AND REMOVAL TOOLS SHALL BE IN ACCORDANCE WITH AS81969/1 OR AS81969/14. AEROSPACE STANDARD $6 SHEET 4 OF 4 REV.

12、 B CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, CRIMP CONTACTS, (DUAL INSERT, TYPE IV, CLASS 1, (-65 TO +125 C), SERIES 2, SHELL DESIGNATOR A) SPECIFICATION NOTES 1. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REV

13、ISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.