SAE AS 81714 24-2001 TERMINAL JUNCTION SYSTEM TERMINAL JUNCTION BLOCKS SECTIONAL ELECTRONIC IN-LINE JUNCTIONS DOUBLE INTEGRAL DIODE(S) SERIES I《I FSC 5940系列整体二极管双线电子内嵌连接截面终端连接块终端连.pdf

1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, ELECTRONIC, IN-LINE JUNCTIONS, DOUBLE, INTEGRAL DIODE(S), SERIES IAS81714/24Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmit

2、ted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WE

3、B ADDRESS: http:/www.sae.org ISSUED 2001-07REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/24SHEET 1 OF 5 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthi

4、s report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcance

5、lled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/24 RATIONALE AS81714/24 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEE

6、N TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-T-81714/24B AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/24B. ANY P

7、ART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AN

8、D STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES

9、, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.AEROSPACE STANDARD AS81714/24SHEET 2 OF 5 TERMINAL JUNCTION

10、 SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, ELECTRONIC, IN-LINE JUNCTIONS, DOUBLE, INTEGRAL DIODE(S), SERIES I THE COMPLETE REQUIREMENTS FOR ACQUIRING THE ELECTRONIC IN-LINE JUNCTION DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-81714.FIGURE 1. STYLE 1

11、, SINGLE DIODE IN-LINE JUNCTION (REF TABLE I).TABLE I. STYLE 1, PART NUMBERS.AEROSPACE STANDARD AS81714/24SHEET 3 OF 5 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, ELECTRONIC, IN-LINE JUNCTIONS, DOUBLE, INTEGRAL DIODE(S), SERIES I FIGURE 2. STYLE 2, TWO DIODE IN-LINE JUNCTION (REF

12、TABLE II).TABLE II. STYLE 2, PART NUMBERS.AEROSPACE STANDARD AS81714/24SHEET 4 OF 5 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, ELECTRONIC, IN-LINE JUNCTIONS, DOUBLE, INTEGRAL DIODE(S), SERIES I FIGURE 3. STYLE 3, TWO DIODES IN-LINE JUNCTION (ZENER & LOW POWER RECT).TABLE III. PAR

13、T NUMBERS FOR STYLE 3.REQUIREMENTS:1. MATERIALS:a. CURRENT CARRYING MEMBERS OF THE IN-LINE JUNCTION SHALL BE IN ACCORDANCE WITH THE IN-LINE JUNCTION SPECIFICATION.b. HOUSING SHALL BE COVERED BY SHRINK TUBING AND/OR SHROUDED WITH GROMMET MATERIAL.AEROSPACE STANDARD AS81714/24SHEET 5 OF 5 TERMINAL JUN

14、CTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, ELECTRONIC, IN-LINE JUNCTIONS, DOUBLE, INTEGRAL DIODE(S), SERIES I NOTES:1. DIMENSIONS ARE IN INCHES.2. MIL-T-81714 REQUIREMENTS APPLY TO BASIC IN-LINE JUNCTION ONLY. FOR RATING AND CHARACTERISTICS OF ELECTRONIC COMPONENT(S), CONSULT COMPONENT SPECI

15、FICATION.3. TOOL FOR CONTACT INSERTING/REMOVAL IS M81969/14-02 OR M81969/8-04 OR M81969/8-06 AND SHALL BE ORDERED SEPARATELY.4. METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM.5. INTERNATIONAL INTEREST, SEE SPECIFICATION MIL-T-817

16、14.6. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, MODULE CLASS D, STYLE NUMBER (SEE FIGURES), AND ELECTRONIC COMPONENT/CIRCUIT DASH NUMBER (SEE TABLES).PART NUMBER EXAMPLE:M81714/24-1D001DIODE IN-LINE JUNCTION, SIZE 22, STYLE 1, WITH 001 CIRCUIT (ONE JAN 1N5618 DIODE).7. CLASSES A, B AND C ARE COMPONENTS INACTIVE FOR NEW DESIGN. ONLY CLASS D COMPONENTS SHALL BE USED FOR DIRECT GOVERNMENT ACQUISITION.