SAE AS 81714 5-1998 TERMINAL JUNCTION SYSTEM RACK ASSEMBLY TRACK FEEDBACK TYPE SERIES I《I FSC 5940系列跟踪反馈型框架装配终端连接系统》.pdf

1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, RACK ASSEMBLY, TRACK FEEDBACK TYPE, SERIES I AS81714/5Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, p

2、hotocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-07REAFFIRMED 2012-

3、01THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/5SHEET 1 OF 6 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and sui

4、tability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE va

5、lues your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/5 RATIONALE AS81714/5 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-T-81714/

6、5F AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/5F. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNC

7、HANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTI

8、ONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODU

9、CTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REPORT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without

10、license from IHS-,-,-AEROSPACE STANDARD AS81714/5SHEET 2 OF 6 TERMINAL JUNCTION SYSTEM, RACK ASSEMBLY, TRACK FEEDBACK TYPE, SERIES I THE COMPLETE REQUIREMENTS FOR ACQUIRING THE RACK DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-81714.Copyright SAE Intern

11、ational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81714/5SHEET 3 OF 6 TERMINAL JUNCTION SYSTEM, RACK ASSEMBLY, TRACK FEEDBACK TYPE, SERIES I Copyright SAE International Provided by IHS under license w

12、ith SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81714/5SHEET 4 OF 6 TERMINAL JUNCTION SYSTEM, RACK ASSEMBLY, TRACK FEEDBACK TYPE, SERIES I TABLE ICopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduc

13、tion or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81714/5SHEET 5 OF 6 TERMINAL JUNCTION SYSTEM, RACK ASSEMBLY, TRACK FEEDBACK TYPE, SERIES I REQUIREMENTS:1. MATERIALS:RACK AND LOCKING CLAMP; ALUMINUM ALLOY 6063, TEMPER T5 IN ACCORDANCE WITH QQ-A-200/9 OR STAINLESS STEEL

14、IN ACCORDANCE WITH QQ-S-766.2. FINISH: ALUMINUM PARTS SHALL BE ANODIC COATED IN ACCORDANCE WITH MIL-A-8625, TYPE II, CLASS 2, BLACK. STAINLESS STEEL PARTS SHALL BE PASSIVATED IN ACCORDANCE WITH QQ-P-35.3. THE RACK SHALL BE DESIGNED FOR INSTALLATION OF MIL-T-81714/1 THRU /4 AND /17 THRU /20 AND /25 B

15、LOCKS.4. ZONE NUMBERS AND ZONE LINES SHALL BE WHITE.5. RACK TO BE FREE OF ALL BURRS AND SHARP EDGES .015R MAX.6. LOCKING CLAMP SHALL BE DESIGNED TO BE PERMANENTLY RETAINED IN RACK. THE LOCKING CLAMP SCREW SHALL BE CROSS RECESSED IN ACCORDANCE WITH MS9006, 8-32UNC-2A X .500, CORROSION-RESISTANT STEEL

16、, PASSIVATED, SELF-LOCKING.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81714/5SHEET 6 OF 6 TERMINAL JUNCTION SYSTEM, RACK ASSEMBLY, TRACK FEEDBACK TYPE, SERIES I NOTES:1. UNL

17、ESS OTHERWISE SPECIFIED, DIMENSIONS IN INCHES, TOLERANCES: DECIMALS .005.2. STOP DESIGN OPTIONAL. SEE DETAILS A AND B.3. THE PART NUMBER CONSISTS OF THE LETTER M, SPECIFICATION SHEET NUMBER, AND A DASH NUMBER FROM TABLE I. WHEN PARTS ARE MADE FROM ALUMINUM, ADD NO LETTER AFTER THE DASH NUMBER. WHEN

18、PARTS ARE MADE FROM STAINLESS STEEL, ADD AN S AFTER THE DASH NUMBER.PART NUMBER EXAMPLE:M81714/5-1FEEDBACK TYPE RACK ASSEMBLY DASH NUMBER.4. METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL IINFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM.5. INTERNATIONAL INTEREST, SEE SPECIFICA

19、TION MIL-T-81714.6. LOCKING CLAMP SHALL BE DESIGNED TO BE PERMANENTLY RETAINED IN RACK. THE LOCKING CLAMP SCREW SHALL BE CROSS-RECESSED IN ACCORDANCE WITH MS9006, 8-32UNC-2A X .500, CORROSION-RESISTANT STEEL, PASSIVATED, SELF-LOCKING OR EQUIVALENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-