SAE AS 81790A-2011 Connectors Receptacle External Electric Power Aircraft General Specification for《飞机的连接器 插座 外部电源的一般规格说明》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2011 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS81790AAEROSPACESTANDARDAS81790 REV. A Issued 2002-03 Reaffirmed 2008-04 Revised 2011-07Connec

5、tors, Receptacle, External Electric Power, Aircraft General Specification for FSC 5935 RATIONALELimit scope revision required to incorporate AS81790-A3. This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope This specification covers t

6、he requirements for aircraft external electric power receptacles. 1.2 Part Numbers Receptacles, covers and shields shall be identified by the MS part numbers shown on the applicable military standard. 2. APPLICABLE DOCUMENTS 2.1 SAE Publications Available from SAE International, 400 Commonwealth Dri

7、ve, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS-QQ-A-250 Aluminum and Aluminum Alloy, Plate and Sheet, General Specification for J452 General Information Chemical Compositions, Mechanical and Physical Properties of SAE Aluminum

8、Casting Alloys AMS4290 Aluminum Alloy, Die Castings, 9.5Si 0.50Mg (360.0-F) As Cast AMS4291 Aluminum Alloy, Die Castings, 8.5Si 3.5Cu (A380.0-F) As Cast AS7974 Cable Assemblies and Attachable Plugs, External Electrical Power, Aircraft, General Specification For AS17845 Shield for Use with MS90362 Ex

9、ternal Power Receptacles AS25018 Connector, Receptacle, External Electric Power, Aircraft, 28 Volt DC, Jet Starting AS35051 Cover for Use with MS90362 External Power Receptacle AS35061 Connector, Receptacle External Electric Power, Aircraft, 28 Volt DC Operating Power SAE AS81790A Page 2 of 19AS9036

10、2 Connector, receptacle, External Electric Power, Aircraft, 115/200 Volt, 400 Hertz 2.2 U.S. Government Publications Available from the Document Automation and Production Service (DAPS), Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Tel: 215-697-6257, http:/assist.daps.dla.mil/quick

11、search/.2.2.1 Specifications and Standards: The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications a

12、nd Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONSFederalTT-P-1757 Primer Coating, Zinc Chromate, Low-Moisture Sensitivity MilitaryMIL-DTL-5541 Detail Specification: Chemical Conversion Coatings on Aluminum and Aluminum Alloys MIL-S-7742 Screw Threads, Standard,

13、Optimum Selected Series, General Specification for MIL-A-8625 Anodic Coatings, for Aluminum and Aluminum Alloys MIL-PRF-85582 Performance Specification: Primer Coatings: Epoxy, Waterborne STANDARDSMilitaryMIL-STD-129 Marking for Shipment and Storage MIL-STD-130 Identification Marking of U.S. Militar

14、y Property MIL-STD-202 Test Methods for Electronic and Electrical Component Parts MIL-STD-889 Dissimilar Metals MIL-STD-1285 Marking of Electrical and Electronic Parts MIL-STD-2073-1 Standard Practice for Military Packaging MS35335 Washer, Lock, Flat-External Tooth 2.2.2 Other Government Documents,

15、Drawings and Publications: The following other Government documents, drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. SAE AS81790A Page 3 of 192.3 Non-Government Publications: The follow

16、ing document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODI

17、SS are the issues of the documents cited in the solicitation (see 6.2). 2.3.1 AIA Publications Available from Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209-3928, Tel: 703-358-1000, www.aia-aerospace.org.NASM961 Washer, Flat, Electrical NASM35650 Nut, Plain,

18、 Hexagon, Machine Screw, UNF-2B 2.3.2 ANSI Publications Available from American National Standards Institute, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org.ANSI/ISO 10012-1 Quality Assurance Requirements for Measuring Equipment 2.3.3 ASQ Publications Available from Am

19、erican Society for Quality, 600 North Plankinton Avenue, Milwaukee, WI 53203, Tel: 800-248-1946 (United States or Canada) or +1-414-272-8575 (International), www.asq.org.ASQC Z1.4 Sampling Procedures and Tables for Inspection by Attributes 2.3.4 ASTM Publications Available from ASTM International, 1

20、00 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM B26 Standard Specification for Aluminum Alloy Sand Castings ASTM B85 Standard Specification for Aluminum Alloy Die Castings ASTM B108 Standard Specification for Aluminum Alloy Permanent Mold C

21、astings ASTM B193 Resistivity of Electrical Conductor Materials ASTM B209 Standard Specification for Aluminum-Alloy Sheet and Plate ASTM B700 Standard Specification for Electrodeposited Coatings of Silver for Engineering Use ASTM D5948 Standard Specification for Molding Compounds, Thermosetting 2.3.

22、5 NCSL Publications National Conference of Standards Laboratories, 2995 Wilderness Place, Suite 107, Boulder, CO 80301-5404, Tel: 303-440-3339, www.nclsi.org.NCSL Z540-1 General Requirements for Calibration Laboratories and Measuring and Test EquipmentSAE AS81790A Page 4 of 192.4 Order of Precedence

23、 In the event of a conflict between the text of this specification and the references cited herein (except for associate detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applica

24、ble laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification Sheets The individual item requirements shall be as specified herein and in accordance with the applicable specification sheet. In the event of any conflict between requirements of this specific

25、ation and the specification sheet, the latter shall govern. 3.2 Qualification Power receptacles furnished under this specification shall be products which are authorized by the qualifying activity for listing on the applicable Qualified Products List (QPL) at the time of award of contract (see 4.4 a

26、nd 6.7). 3.3 Materials Materials shall conform to the applicable specification as specified and shall be suitable for the performance required herein. Unless suitably protected against electrolytic corrosion, dissimilar metals shall not be employed in intimate contact with each other. Dissimilar met

27、als are defined in MIL-STD-889. Materials used in the construction of connectors, bases, covers and shields shall be fungus inert in accordance with requirement 4 of MIL-STD-454. All materials shall be certified as specified in 4.6.9. 3.3.1 Bases: Bases shall be fabricated using a fiber filled, impa

28、ct resistant, polyethylene terephthalate material conforming to MIL-M-14 type SDI-30, an impact resistant fiber filled polyester material, or an impact resistant fiber filled epoxy material. Alternate materials may be used if approved by the qualifying activity (see 6.7). Such materials must be equi

29、valent or superior to type SDI-30 material. 3.3.2 Shields: Cast shields shall be 356-T6 aluminum alloy in accordance with QQ-A-596 or shall be die cast aluminum alloy A380 in accordance with QQ-A-591. Shields made from sheet stock shall be 5052 aluminum alloy in accordance with QQ-A-250/8; minimum t

30、hickness .060 inch. Shields shall be anodized in accordance with MIL-A-8625 Types I or II, or chemically surface-treated in accordance with MIL-C-5541, Class 2. Coat with one coat of zinc chromate primer according to TT-P-1757 or with water borne epoxy primer according to MIL-P-85582. 3.3.3 Contacts

31、: The small pin contacts shall be tellurium copper, leaded copper, or brass, with a minimum of 0.0002 inch of silver plate. The large pin contacts shall be tellurium copper, or leaded copper or equivalent materials approved by the qualifying activity with a minimum of 0.0002 inch of silver plate. Wh

32、en tested in accordance with 4.6.11, the conductivity of the material used to make the large gage contacts shall be a minimum of 90% of the International Annealed Copper Standard (IACS). 3.3.4 Covers: Covers used for protecting the rear of receptacles shall be of a shatterproof synthetic rubber or p

33、henolic compound of 85 to 95 shore hardness and suitable to meet the performance specified herein. 3.4 Design and Construction Receptacle assemblies and covers shall be designed and constructed in accordance with the applicable military standards and as specified herein. 3.4.1 Contacts: Unless appro

34、ved by the qualifying activity, the contact shall be designed from a one piece alloy material. Contacts must conform to the physical dimensions of this specification and related military standards (see 4.6.2). 3.4.1.1 Identification: Contact identification shall be permanently and legibly marked on

35、the front and rear of the base. 3.4.1.2 Method of attachment: A positive means shall be provided to anchor contacts in the base. SAE AS81790A Page 5 of 193.4.1.3 Cross-sectional area: The cross-sectional area throughout each contact shall be no less than the root area of the thread at any point. 3.4

36、.1.4 Terminal pads: Each terminal shall include an integral or force-fitted pad. 3.4.1.5 Threads on terminals: Threads on terminals shall conform to MIL-S-7742. Each large terminal shall be threaded to within 0.125 inch of its pad and each small terminal shall be threaded to within 0.062 inch of its

37、 pad. 3.4.1.6 Terminal hardware: Each base shall be provided with one nut MS35650-3385T, one lockwasher MS35335-91, and one flat washer AN961-616 for each large terminal; one nut MS35650-305T, one lockwasher MS35335-88, and one flat washer AN961-10 for each small terminal. 3.4.1.7 Hardness of contac

38、ts: The hardness at all points on the sides of each pin shall be at least 86 to 100 Brinell or Rockwell B 40-56 (see 4.6.16). 3.4.2 Shields: Each shield, including all rivets and welds, shall be contained within the maximum dimensions shown on the standard. The inside of each shield shall be smooth

39、and free from protrusions and sharp edges. 3.4.3 Dimensions (see 3.1): The dimensions of the receptacle assemblies and associated parts shall be in accordance with the applicable MS sheet. 3.4.4 Weight: When tested as specified in 4.6.3, the weight of each item shall not exceed the value specified o

40、n the applicable Military Standard. 3.5 Performance Each item shall perform satisfactorily when subjected to the following conditions applicable to that item. 3.5.1 Impact: There shall be no fractures or cracks of the receptacle assembly and no loosening of shields or contacts when items are subject

41、ed to impact tests after exposure to -55 C in accordance with 4.6.4. 3.5.2 Terminal torque strength: Receptacle assemblies shall be capable of withstanding torque in accordance with 4.6.5. As a result of the application of torque there shall be no cracking, delamination or chipping of the base. The

42、contacts shall not shear, crack or rotate. 3.5.3 Flexural strength, receptacle base: Receptacle bases, less center contacts, shields, and other accessories, shall not break when subjected to a minimum force of 1300 pounds for three-pin receptacles, and a minimum 3500 pounds for six-pin receptacles w

43、hen tested in accordance with 4.6.6. 3.5.4 Pin static bending strength: Receptacle assemblies shall be capable of withstanding forces applied to the pins in accordance with 4.6.7. The pins shall not take a permanent set of more than .01 inch at the mating end. There shall be no cracking, delaminatio

44、n or chipping of the base and the contacts shall not come loose in the base. 3.5.5 Shield and attachment static strength: Shields shall be capable of withstanding forces applied to the shield in accordance with 4.6.8. The sides of the shield shall not be displaced greater than the amount specified w

45、hile the forces are applied. After the forces are removed, the shield shall conform to the dimensions shown on the applicable standard. There shall be no cracking, delamination or chipping of the base and the shield shall not come loose from the base. 3.6 Environmental 3.6.1 Thermal shock: Receptacl

46、e assemblies and covers shall not crack, fracture, or delaminate when subjected to temperature extremes in accordance with 4.6.12. 3.6.2 Salt spray: The receptacle assemblies, shields and covers shall show no evidence of corrosion when tested in accordance with 4.6.14. SAE AS81790A Page 6 of 193.6.3

47、 Humidity: Receptacle assembly and cover as appropriate shall withstand the humidity exposure as described in 4.6.13 followed by a dielectric withstanding voltage test defined in 4.6.15. 3.6.4 Dielectric withstanding: The voltage shall be 60 Hz 2500 100 volt rms with a current leakage of less than 1

48、.0 milliamperes when tested in accordance with 4.6.15. 3.7 Identification of Product Each item shall be marked as follows for identification in accordance with MIL-STD-130: Specification Part Number Manufacturers Part Number Manufacturers Name or Trademark Date Indicator which defines manufacturing

49、dates for periods 3 months or less 3.7.1 Location of markings: Identification markings shall be located as follows: a. Three-pin receptacles. Identification markings shall be located on the shield. b. Six-pin receptacles. Identification markings shall be located on the pin side of the base a minimum of 5/8” from the perimeter. c. Shield, six-pin receptacles. Identification markings shall be located on the shield. d. Cover, six-pi